Bosscat parts

The place for all things Schumacher.

Moderators: scr8p, klavy69

Post Reply
Bosscat
Regular Member
Posts: 3
Joined: Fri Jan 09, 2015 2:51 pm

Bosscat parts

Post by Bosscat »

I am rebuilding my old Bosscat. I need some diff. pulleys, front and rear. And the layshaft pulley.
Does anybody know where to get these items, either plastic or preferably aluminium? Perhaps something from another schumacher model?

Peter K

User avatar
DennisM
Approved Member
Posts: 2403
Joined: Sun Feb 26, 2012 7:07 am
Location: Denmark
Has thanked: 30 times
Been thanked: 64 times

Re: Bosscat parts

Post by DennisM »

Yup, all it takes is Ebay - a strong wallet and good patience :wink:
Gone fishing

Bosscat
Regular Member
Posts: 3
Joined: Fri Jan 09, 2015 2:51 pm

Re: Bosscat parts

Post by Bosscat »

Yes but is it possible to fit a diff drum from another model on to my bosscat or to by a knock off?

Peter K

Peakey
Approved Member
Posts: 578
Joined: Tue Feb 25, 2014 3:55 am
Location: Nottingham, UK
Been thanked: 3 times

Re: Bosscat parts

Post by Peakey »

Basically yes you can, the only differance with the rear drums were the 23mm Pro Bosscat diff which was wider than the others as it ran extra bearings inside and alloy outputs.

This is a 23mm Pro rear diff that I've just fitted into my Procat

Image

That has replaced this Trinity one

Image

If yours has a pro rear drumb in and you replace it with another one over rebuilding yours you will need different eccentrics, with the pro diff being wider you have shorter ones over the standed Procat ones.

Bosscat
Regular Member
Posts: 3
Joined: Fri Jan 09, 2015 2:51 pm

Re: Bosscat parts

Post by Bosscat »

I think I will be succesfull in rebuilding my pro diff. but my drive shafts are rather worn down. The U1692 set would be ideal, but is not to be found on ebay. Can I use drive shafts from another model?

Peter K

Peakey
Approved Member
Posts: 578
Joined: Tue Feb 25, 2014 3:55 am
Location: Nottingham, UK
Been thanked: 3 times

Re: Bosscat parts

Post by Peakey »

U1692 which is that? I've got some new U630 I think somewhere

Image

User avatar
Incredible_Serious
Approved Member
Posts: 3380
Joined: Tue Jan 29, 2008 12:09 am
Location: Melbourne, Victoria, Australia
Has thanked: 1332 times
Been thanked: 796 times

Re: Bosscat parts

Post by Incredible_Serious »

Bosscat wrote:I think I will be succesfull in rebuilding my pro diff. but my drive shafts are rather worn down. The U1692 set would be ideal, but is not to be found on ebay. Can I use drive shafts from another model?

Peter K
U1692 is Nitro 10 Mk3 driveshafts... they're pretty much the same parts, apart from the diff outputs, which aren't included in the U1692, but are included in the U704 (Bosscat / Nitro 10 Mk1 and 2) and U630 (ProCat 4wd rear).

Alex
Osiris is the key.

"The world looks so much better through beer goggles... except Farmer in his underwear" - Ken

Look out for Todd K. - he's a convicted serial killer!!!

Welshy40
Approved Member
Posts: 304
Joined: Tue Aug 09, 2011 1:55 am
Location: Surrey, England

Re: Bosscat parts

Post by Welshy40 »

Anyone know where i can get the alloy ujs for the Bosscat?
Designer of the Lazer ZX / ZXR Tub Chassis (now available again from Fibre-Lyte)

Sponser links below
http://www.fibre-lyte.co.uk/
http://www.kamtec.co.uk/

User avatar
klavy69
Moderator
Posts: 5136
Joined: Thu May 29, 2008 4:11 pm
Location: Fulton, IL (Land of one stop light but we DO have a windmill!)
Has thanked: 532 times
Been thanked: 253 times

Re: Bosscat parts

Post by klavy69 »

Seen some pricey ones on ebay last night. Were in a lot with a chassis and maybe some arms...

Todd
Peace and professionlism.....Kabunga signing off!!!

User avatar
LurkingCAT
Approved Member
Posts: 276
Joined: Wed Jul 04, 2012 6:11 am
Location: Norway
Has thanked: 81 times
Been thanked: 132 times

Re: Bosscat parts

Post by LurkingCAT »

Bosscat wrote:I think I will be succesfull in rebuilding my pro diff. but my drive shafts are rather worn down. The U1692 set would be ideal, but is not to be found on ebay. Can I use drive shafts from another model?

Peter K


Not alloy but for one of my runners I'm using the the diff out put yokes U1631. They're still available from Schumacher.

In combination with:

a pointer in the direction of Traxxas Slash. Wheel hubs and out drives does not fit, but the telescopic axles and the universal joints are direct fits - just cut down the length of the axles as required. Diameter and legth of the pins in the uj's are the same.

Sturdy set of axles for a runner

Best, David

Welshy40
Approved Member
Posts: 304
Joined: Tue Aug 09, 2011 1:55 am
Location: Surrey, England

Re: Bosscat parts

Post by Welshy40 »

I got a pair of alloy ujs, now to get a shell and paint it.
Designer of the Lazer ZX / ZXR Tub Chassis (now available again from Fibre-Lyte)

Sponser links below
http://www.fibre-lyte.co.uk/
http://www.kamtec.co.uk/

Post Reply

Create an account or sign in to join the discussion

You need to be a member in order to post a reply

Create an account

Not a member? register to join our community
Members can start their own topics & subscribe to topics
It’s free and only takes a minute

Register

Sign in

  • Similar Topics
    Replies
    Views
    Last post
  • Bosscat. Or?
    by Johanp » » in Schumacher Forum
    13 Replies
    481 Views
    Last post by Johanp
  • BossCat
    by ultimapro » » in Schumacher Forum
    5 Replies
    1891 Views
    Last post by DennisM
  • new to me bosscat
    by top cat mike » » in Schumacher Forum
    3 Replies
    896 Views
    Last post by Jay Dub
  • bosscat questions
    by PerKr » » in Schumacher Forum
    5 Replies
    1595 Views
    Last post by MarcosGraveyard
  • Lipos in a bosscat?
    by autoxvw » » in Schumacher Forum
    4 Replies
    1599 Views
    Last post by Danf1275
  • Found another BossCat
    by perry » » in Schumacher Forum
    12 Replies
    2049 Views
    Last post by Incredible_Serious
  • Bosscat gone XLS
    by 19RC80KS » » in Schumacher Forum
    21 Replies
    5662 Views
    Last post by 19RC80KS
  • Schumacher Bosscat
    by Mja75 » » in The Gallery
    0 Replies
    476 Views
    Last post by Mja75

Return to “Schumacher Forum”

Who is online

Users browsing this forum: No registered users and 13 guests