RPM front knuckles - Bearing sizes - RC10Talk - The Net's Largest Vintage R/C Community

RPM front knuckles - Bearing sizes

Moderators: scr8p, klavy69

3 posts • Page 1 of 1

zzzubbb: Regular Member; Posts: 22; Joined: Thu May 26, 2016 12:06 pm; Location: Perth, Scotland, UK; Has thanked: 2 times; Been thanked: 1 time

RPM front knuckles - Bearing sizes

Quote

Post by zzzubbb » Fri Jun 10, 2016 2:04 am

Can anyone tell me the bearing sizes required to install RPM knuckles.

I recently aquired a set but the standard bearings were too big to fit.

Thanks,

Z

rccars4sal: Approved Member; Posts: 1001; Joined: Thu Aug 22, 2013 1:05 pm; Location: USA; Been thanked: 1 time

Re: RPM front knuckles - Bearing sizes

Quote

Post by rccars4sal » Fri Jun 10, 2016 9:04 pm

Should be 5x10, as those were sold for Kyosho cars also.

GoMachV: Approved Member; Posts: 11203; Joined: Sun Apr 29, 2012 10:31 pm; Location: Twin Falls, ID; Has thanked: 768 times; Been thanked: 2218 times

Re: RPM front knuckles - Bearing sizes

Quote

Post by GoMachV » Fri Jun 10, 2016 9:41 pm

5x10 flanged from memory

It's time to stand up to the bully. Support the companies that support the industry, not the ones that tear it down. Say no to Traxxas
Factory Works website

Post Reply

3 posts • Page 1 of 1

Create an account or sign in to join the discussion

You need to be a member in order to post a reply

Create an account

Not a member? register to join our community
Members can start their own topics & subscribe to topics
It’s free and only takes a minute

Sign in

Similar Topics

Replies

Views

Last post

jrx2 Bearing sizes

Last post by zuki250 « Fri Dec 27, 2013 2:03 pm
Posted in Losi Forum
Replies: 5
by zuki250 » Fri Dec 27, 2013 9:49 am » in Losi Forum

First post

Hey guys,

So i am pretty much done rebuilding my Jrx2...but i have a nice crunchy sound from the bearings on the rear end...I want to grab some avid's but i don't know the complete size...Avid asks for 3 dimensions... I know they are 8mm x 14mm,...

Last post

Thanks Dan...i actually have some that i used on my optima...so i will just swap those in..i should have waited to put the whole thing back together before i did it...hahah

5 Replies

1132 Views

Last post by zuki250
Fri Dec 27, 2013 2:03 pm
Junior t Transmission bearing sizes

Last post by hudson hornet ! « Wed Aug 03, 2016 3:00 pm
Posted in Losi Forum
Replies: 5
by hudson hornet ! » Tue Aug 02, 2016 9:05 pm » in Losi Forum

First post

I am trying to resurrect an old junior t. I have no manuals and would like to know what size bearings would go in the transmission. I would like to replace all bushings with bearings. If anyone can be of assistance I would appreciate it.

Thanks!

Last post

Thank you all. I am proud to be a member on this forum even though I do not post much.

5 Replies

1089 Views

Last post by hudson hornet !
Wed Aug 03, 2016 3:00 pm
stealth tranny bearing sizes ?

Last post by raserx08 « Tue Jan 29, 2013 9:20 pm
Posted in Temple's RC10 Tech Forum
Replies: 8
by Jason Pelletier » Thu Mar 05, 2009 5:23 pm » in Temple's RC10 Tech Forum

First post

New to the forum and trying to get my old rc10 in good shape. I have read alot of stuff on here and love the builds. I think it's a 1992 rc10ce. Gold tub white plastics. I'll get pics up.

Any one have a list of the sizes ? Tranny is a white stealth.

Last post

I would rebuild it also I had a t3 that I took apart to replace the bearings I put it all back together and then 10 min after running it was just slipping like crazy because the screw and t-nut kept coming loose so I took it apart again rebuilt the...

8 Replies

1345 Views

Last post by raserx08
Tue Jan 29, 2013 9:20 pm
Bearing sizes for 6 gear tranny?

Last post by philk « Wed Aug 05, 2009 5:05 pm
Posted in Temple's RC10 Tech Forum
Replies: 3
by philk » Wed Aug 05, 2009 4:20 pm » in Temple's RC10 Tech Forum

First post

Sorry if this was covered before....... I tried to search for this and came up with nothing. Do any of you know the sizes to replace all of the bearings in the original 6 gear tranny?
Thanks.

Last post

THANKS!

3 Replies

471 Views

Last post by philk
Wed Aug 05, 2009 5:05 pm
Losi JRX Bearing Sizes

Last post by aconsola « Sun Aug 23, 2009 9:55 am
Posted in Losi Forum
Replies: 1
by JPAE07 » Sun Aug 23, 2009 2:29 am » in Losi Forum

First post

I hope I'm not duplicating a thread here.

Can someone provide the bearing sizes for trans, rear hubs, front wheels ? Basically all for the JRX-2/T

Thanks.

Last post

8x14 x4 (outdrive gears)
5/16x1/2 x2 (differential support)
1/4x3/8 x1 (diff gear)
3/16x3/8 x10 Everything else

1 Replies

317 Views

Last post by aconsola
Sun Aug 23, 2009 9:55 am
Verify bearing sizes for 9481

Last post by civilguy « Tue Sep 01, 2009 11:36 pm
Posted in Temple's RC10 Tech Forum
Replies: 2
by civilguy » Tue Sep 01, 2009 11:08 pm » in Temple's RC10 Tech Forum

First post

A very nice man sold me 3 sets of 2.2 buggy fronts (9481). Now I just need to get bearings.... I am an old school RC10 guy and only have the flanged bearings from bitd. I think 3/16 x 3/8 x 1/8 is the right size and should go right on my original...

Last post

I thought so, but before clicking BUY IT NOW, I figured I'd ask it now. :lol:

Thanks.

2 Replies

277 Views

Last post by civilguy
Tue Sep 01, 2009 11:36 pm
Bearing sizes for a 6 gear RC10?

Last post by Brat « Mon Aug 02, 2010 6:14 am
Posted in RC10 Buggy Forum
Replies: 14
by stampede_dude » Sun Nov 29, 2009 2:08 pm » in RC10 Buggy Forum

First post

I searched the forums and internet and can't find a direct answer...What sizes and how many of each bearing do I need to outfit an original RC10 with the six gear transmission, no bellcrank steering? Boca Bearings has kits for the RC10, but the...

Last post

If you intend to run the 6 gear tranny, I'll suggest that you go on with the mod. It'll be alot smoother and you will have longer running time on the idler gears. I've done that on my 6 gear tranny and no regrets. PS: As long as you are not gearing...

14 Replies

3735 Views

Last post by Brat
Mon Aug 02, 2010 6:14 am
Ball raced steering bearing sizes

Last post by USA-1 « Fri Dec 24, 2010 10:33 pm
Posted in RC10 Truck Forum
Replies: 6
by Caine » Thu Dec 23, 2010 6:51 pm » in RC10 Truck Forum

First post

I'm buying one of these alu steering sets for my 10t:

It says it has 5x8 delrin bushes now would this mean i need 5x8x2.5 bearings to go in there as this is the only size i can find that matches on avidrc?

I can wait if needs be but need to put...

Last post

The only ones I seen is from MIP vintage stuff. I was using the stock ones on my RC10T Duratrax conversion until I seen these on Ebay.

I use an A&L steering and made a custom front adjustable bracket.
Just some of the options you can do.

6 Replies

805 Views

Last post by USA-1
Fri Dec 24, 2010 10:33 pm

Return to “Yokomo Forum”

Who is online

Users browsing this forum: Google Adsense [Bot], Trendiction [Bot] and 25 guests

RPM front knuckles - Bearing sizes

RPM front knuckles - Bearing sizes

Re: RPM front knuckles - Bearing sizes

Re: RPM front knuckles - Bearing sizes

Create an account or sign in to join the discussion

Create an account

Sign in

Who is online

Login Register