Page 1 of 1
Repro Protech 4 body (wide problem)
Posted: Sat Dec 31, 2016 8:46 am
by prp
Hi guys
I remember a post on, but I can't find the post , on some trouble with the wide of the undertray TBG
and the chassis wide on the 870c...
Thanks for help Pierre PRP
Re: Repro Protech 4 body (wide problem)
Posted: Sat Dec 31, 2016 8:54 am
by scr8p
I had a problem with mrlexan's 870c undertray that seemed to be just a tad bit narrow for the chassis. His was a reproduction of an original. I'm pretty sure TBG's is a reproduction or mrlexan's reproduction so I'm sure it worse.
Re: Repro Protech 4 body (wide problem)
Posted: Sat Dec 31, 2016 10:52 am
by Peakey
Try Steve (Penguin bodies) on eBay he's made a new mold and they seem to fit better than the TBG ones
Re: Repro Protech 4 body (wide problem)
Posted: Wed Jan 04, 2017 10:32 am
by tamiyadan
.
Re: Repro Protech 4 body (wide problem)
Posted: Fri Jan 06, 2017 6:23 am
by Peakey
tamiyadan wrote:FYI all the reproductions are narrow. mr lexan, Penguin that other one that starts with a W or M i can't remember are all not great, TBG are the worst versions.
TBG they are warped and really narrow, like he pulled them off the molds way too early before the lexan cooled.
the others are better however if you really want it to fit well you will have to narrow your chassis about 2-3mm, especially by the front elbow.
otherwise it will fit so tight and narrow that the paint will just come off the first time you push it on the chassis.
When did you last try a Penguin one? I ask cus he's made a new mold recently and said he's added some to it to make it fit properly, I've got one but as yet haven't tried it yet but it's not destiny for a 870 anyway
Re: Repro Protech 4 body (wide problem)
Posted: Fri Jan 06, 2017 11:05 am
by tamiyadan
.
Re: Repro Protech 4 body (wide problem)
Posted: Fri Jan 06, 2017 12:39 pm
by Peakey
The one that he's selling on eBay now is the latest one and I think he said he added about 3mm to the mold. He's been telling me about the molds used and he thinks that TBG must use fibreglass as they shrink with the heat.
Re: Repro Protech 4 body (wide problem)
Posted: Fri Jan 06, 2017 1:01 pm
by tamiyadan
.
Re: Repro Protech 4 body (wide problem)
Posted: Fri Jan 06, 2017 4:16 pm
by prp
The Mr Lexan mold is the original of the Protech IV body ?
I'm a little lost...
Re: Repro Protech 4 body (wide problem)
Posted: Fri Jan 06, 2017 6:21 pm
by scr8p
Mrlexan made a mold from an original under tray. Oldrc.com bought his molds and they can be bought on their site.
Re: Repro Protech 4 body (wide problem)
Posted: Fri Jan 06, 2017 6:27 pm
by RC10th
I know a guy who 3D printed a 1/10 truck cab mold for a commercial project and it was about $3,000 on a high resolution printer.
Re: Repro Protech 4 body (wide problem)
Posted: Sat Jan 07, 2017 1:10 am
by tamiyadan
.
Re: Repro Protech 4 body (wide problem)
Posted: Sat Jan 07, 2017 7:49 am
by mrlexan
tamiyadan wrote:mr lexan was a copy of a copy.
Tamiyadan, that is not a correct statement. Mine were not a copy of a copy. Mine were a copy of an original tray.
Re: Repro Protech 4 body (wide problem)
Posted: Sat Jan 07, 2017 2:02 pm
by Peakey
Steves mold (penguin) was made from an original body and undertray he was trying to buy mine off me but I wouldn't sell it him
Re: Repro Protech 4 body (wide problem)
Posted: Tue Jan 10, 2017 2:59 pm
by tamiyadan
.