TT-02 Dogbone

Moderators: scr8p, klavy69

Post Reply

2 posts • Page 1 of 1

bats: Approved Member; Posts: 63; Joined: Wed Dec 31, 2014 12:11 pm

TT-02 Dogbone

Quote

Post by bats » Thu May 28, 2015 2:07 pm

Does anyone have the measurements for the end(ball portion) of the doggone for a TT-02?

SFC K: Approved Member; Posts: 1336; Joined: Tue Nov 30, 2010 9:24 pm; Location: Oakdale, MN; Has thanked: 47 times; Been thanked: 9 times

Re: TT-02 Dogbone

Quote

Post by SFC K » Thu May 28, 2015 5:34 pm

I found a length on the internet at 31mm. Not sure if that is accurate or not. It was on Asia-t's website for aftermarket dog bones.

I sent you a pm too...

Jeff

Post Reply

2 posts • Page 1 of 1

Create an account or sign in to join the discussion

You need to be a member in order to post a reply

Create an account

Not a member? register to join our community
Members can start their own topics & subscribe to topics
It’s free and only takes a minute

Sign in

Similar Topics

Replies

Views

Last post

DS dogbone ASC8867 replacement HPI86002 sprint dogbone

Last post by LoboNYC « Sat May 14, 2022 5:11 pm
Posted in Temple's RC10 Tech Forum
Replies: 1
by JosephS » Fri May 13, 2022 11:08 pm » in Temple's RC10 Tech Forum

First post

The rc10 dogbone ASC8867 can be replaced by HPI part #86002 - DRIVE SHAFT 6x42mm (DOGBONE x2/SPRINT)

The dog bone ball at 6mm and pins fit Associated outdrives.

I don't have an original part to know if this is a 100% replacement....

Last post

That's good to know.

PM sent

1 Replies

524 Views

Last post by LoboNYC
Sat May 14, 2022 5:11 pm
Help with Dogbone, please

Last post by suby56 « Wed Oct 27, 2010 7:37 am
Posted in RC10 Buggy Forum
Replies: 4
by suby56 » Tue Oct 26, 2010 11:18 pm » in RC10 Buggy Forum

First post

Hello,

My name is Clay, and I am trying to fix up my RC10. One of the dogbones is bent, so I ordered this from Tower to replace it,

SO, I got it in the mail today, it is the correct part number, 6370, but it also says Dogbone b2/b3 underneath and...

Last post

If money isn't tight I would order a Mip CVD kit from Tower. No more lost dogbones.

Money Is no Object! At least until my wife finds out.

So, it sounds like I ordered the right thing, just an odd problem. I will send it back and try again.

4 Replies

656 Views

Last post by suby56
Wed Oct 27, 2010 7:37 am
T4 dogbone source?

Last post by RC10th « Thu Dec 24, 2020 10:09 pm
Posted in RC10 Truck Forum
Replies: 6
by Tk8398 » Tue Dec 22, 2020 10:41 am » in RC10 Truck Forum

First post

I have 2 T4 RTRs, and it seems that the inner ball stud on the rear camber link will loosen up over time and if I don't check them often enough snap off and send the dogbone flying somewhere. The last time it happned I could not find it, and it...

Last post

We used to use long Yokomo ball studs where you could put a nut on the undeside of the brace.

6 Replies

893 Views

Last post by RC10th
Thu Dec 24, 2020 10:09 pm
Dogbone lengths...

Last post by n20capri « Sun Feb 15, 2015 5:25 pm
Posted in Temple's RC10 Tech Forum
Replies: 7
by n20capri » Fri Feb 06, 2015 9:41 am » in Temple's RC10 Tech Forum

First post

Building a mid motor oin RC10 and trying to figure out what dogbones I'll need. Mounting things a bit differently (trans in a slightly different spot/longer arms etc) so it's not as easy as swapping to a B4 bone for example (or maybe it is idk their...

Last post

Anyone have a chance to measure anything? Specifically the B4 dogbone?
Thanks

7 Replies

1920 Views

Last post by n20capri
Sun Feb 15, 2015 5:25 pm
replacement dogbone springs?

Last post by filzemail « Thu Jul 07, 2011 2:38 pm
Posted in Temple's RC10 Tech Forum
Replies: 5
by nfair » Thu May 19, 2011 8:57 am » in Temple's RC10 Tech Forum

First post

I recently got back into RC and have got my A stamped gold pan RC10 running again. I let my younger son drive it the other day while his truck was broken and he ended up crashing it, snapping the screws holding the rear A arms to the pan. That...

Last post

The spring type is not critical. You can use the spring out of a ball point pen, just cut it in half and make sure it is not too long so it does not force the dogbone out of the stub axel. In fact I cut two pieces of spring and set it up so the...

5 Replies

983 Views

Last post by filzemail
Thu Jul 07, 2011 2:38 pm
Raider dogbone question

Last post by ron « Thu May 30, 2013 11:38 pm
Posted in Kyosho Forum
Replies: 4
by mikecel79 » Sun May 19, 2013 8:24 pm » in Kyosho Forum

First post

Hi All,

First post here. I recently pulled out an old Kyosho Raider Pro that I had when I was younger and now I am looking to restore it back to working condition. It's in surprisingly good shape but I am missing dogbones for it. I have 2 pairs of...

Last post

check out this old post on the drive shafts for rocky, raider

the shaft should be 62.5mm from dogbone pin to UV joint. The plastic ones are plastic in the middle but have metal dogbone ends. Must have been done to save cost :roll: If you want the...

4 Replies

1380 Views

Last post by ron
Thu May 30, 2013 11:38 pm
Dogbone and CVD measurements

Last post by jeepy2013 « Tue Mar 07, 2023 7:51 am
Posted in Temple's RC10 Tech Forum
Replies: 5
by Frankentruck » Thu Jan 20, 2022 10:27 pm » in Temple's RC10 Tech Forum

First post

I was thinking there should be a place to get easy reference to know the measurements of buggy and truck dogbones and CVDs. I've got RC10 and B4; RC10T, T2, T3, and T4; Custom Works short and schmedium. This seems like a good starting point. I'm not...

Last post

This will be the initial group getting measured. Most are used, but still straight. Measurements 1 through 9 refer to the graphic in the first post.
.
CVDs and bones group 1.jpg
.
CVDs and bones-1.jpg

That's a lot of great info, thanks for doing...

5 Replies

1683 Views

Last post by jeepy2013
Tue Mar 07, 2023 7:51 am
Re-re-release Dogbone(?) falling out?

Last post by username « Sun Jun 06, 2021 5:16 pm
Posted in RC10 Re-Release Forum
Replies: 5
by username » Sun Jun 06, 2021 2:13 pm » in RC10 Re-Release Forum

First post

So, I've gotten a re-re-released RC10 for my son to go alongside my gold pan. However, his car is throwing the dogbone side of the drive shafts on the transmission side. I remember converting my gold pan to pure dogbones in the 80s, but sincerely...

Last post

That seems to have done the trick. The clearance isn't as much as I'd like, but the dogbone stays within the cup through an entire turn when the arm is as low as it can be. We romped on it a bit and tried to force the issue, but were unable to cause...

5 Replies

1074 Views

Last post by username
Sun Jun 06, 2021 5:16 pm

Return to “Tamiya Forum”

Who is online

Users browsing this forum: Bing [Bot] and 4 guests

TT-02 Dogbone

TT-02 Dogbone

Re: TT-02 Dogbone

Create an account or sign in to join the discussion

Create an account

Sign in

Who is online

Login Register