RC10 Factory Works MIP 93' Worlds Racer Restoration

General discussion, builds/restorations, etc...

Moderators: scr8p, klavy69

Vintagemishal
Approved Member
Posts: 502
Joined: Wed Sep 23, 2009 1:51 pm
Location: Portland, OR
Been thanked: 3 times

Re: RC10 Factory Works MIP 93' Worlds Racer Restoration

Post by Vintagemishal »

Won't do much good to measure the front tires as I made them from a pair of rear Yokomo TR39's. I narrowed them and reduced the diameter. Those Pro-Lines do look like they could be correct. What diameter are the Pro-Lines?

Edit: I found the tires on Ebay and they are the wrong diameter. Eustace was pretty sure they were Yokomo tires, but it was a long time ago. I have been trying to track down Scott Montgomery, but no luck so far.

hugger19
Approved Member
Posts: 1688
Joined: Sun Oct 05, 2008 2:33 pm
Location: 33445 florida
Has thanked: 6 times
Been thanked: 99 times

Re: RC10 Factory Works MIP 93' Worlds Racer Restoration

Post by hugger19 »

does anyone know the part number for the shaft that converts the stealth trans to the 4x4 rc10 kit.

User avatar
littleVETTE
Approved Member
Posts: 1418
Joined: Mon Aug 11, 2008 4:07 pm
Location: U.S.A.
Has thanked: 6 times
Been thanked: 3 times

Re: RC10 Factory Works MIP 93' Worlds Racer Restoration

Post by littleVETTE »

the build has really turned out awesome todd. very impressive work.

i would stick with those yokomo tires you have on. i would also hold off on the decals til someone post another closer and clearer picture of the buggy. it would be a waste to cut up perfectly good decals and tires. someone has to have more pictures of the buggy somewhere. it's a matter of time.

Vintagemishal
Approved Member
Posts: 502
Joined: Wed Sep 23, 2009 1:51 pm
Location: Portland, OR
Been thanked: 3 times

Re: RC10 Factory Works MIP 93' Worlds Racer Restoration

Post by Vintagemishal »

hugger19 wrote:does anyone know the part number for the shaft that converts the stealth trans to the 4x4 rc10 kit.
I think it may be posted somewhere back in this thread? I will try to find it. I know that Aaron would know.

Vintagemishal
Approved Member
Posts: 502
Joined: Wed Sep 23, 2009 1:51 pm
Location: Portland, OR
Been thanked: 3 times

Re: RC10 Factory Works MIP 93' Worlds Racer Restoration

Post by Vintagemishal »

littleVETTE wrote:the build has really turned out awesome todd. very impressive work.

i would stick with those yokomo tires you have on. i would also hold off on the decals til someone post another closer and clearer picture of the buggy. it would be a waste to cut up perfectly good decals and tires. someone has to have more pictures of the buggy somewhere. it's a matter of time.
Thank you much Rob. I think that that is great advice!

aip47-2008
Approved Member
Posts: 1186
Joined: Sun Feb 08, 2009 9:20 pm
Location: Spokane, WA
Has thanked: 132 times
Been thanked: 23 times

Re: RC10 Factory Works MIP 93' Worlds Racer Restoration

Post by aip47-2008 »

hugger19 wrote:does anyone know the part number for the shaft that converts the stealth trans to the 4x4 rc10 kit.

http://www.rc10talk.com/viewtopic.php?f=82&t=586

THUNDERSTRIKE1
Approved Member
Posts: 2022
Joined: Sat Jan 20, 2007 4:41 pm
Location: Cape Carteret.NC
Been thanked: 22 times

Re: RC10 Factory Works MIP 93' Worlds Racer Restoration

Post by THUNDERSTRIKE1 »

the 410m1 looks great since you rewired it.glad i could help out.Did youfind the novak receiver you needed?don

Vintagemishal
Approved Member
Posts: 502
Joined: Wed Sep 23, 2009 1:51 pm
Location: Portland, OR
Been thanked: 3 times

Re: RC10 Factory Works MIP 93' Worlds Racer Restoration

Post by Vintagemishal »

Thanks Don, the 410 was much appreciated! I have a Novak NER-2S, but it is not an exact match. When time and money allows, I will keep looking for stuff I need.

Thanks,

Todd

Vintagemishal
Approved Member
Posts: 502
Joined: Wed Sep 23, 2009 1:51 pm
Location: Portland, OR
Been thanked: 3 times

Re: RC10 Factory Works MIP 93' Worlds Racer Restoration

Post by Vintagemishal »

Found my receiver and will be on it's way!

Image

Vintagemishal
Approved Member
Posts: 502
Joined: Wed Sep 23, 2009 1:51 pm
Location: Portland, OR
Been thanked: 3 times

Re: RC10 Factory Works MIP 93' Worlds Racer Restoration

Post by Vintagemishal »

UPDATE** I was at home sick today, so I got the Novak receiver installed with fuel tubing and antenna. Also installed Futaba mini servo and made a belt guide out of a RC10 battery cup. The chassis is very close to being finished. What do you guys think? I tried to mimic the magazine photo, but it is not quite there.

Image

Image

Image

Image

User avatar
romulus22
Approved Member
Posts: 2448
Joined: Wed May 19, 2010 7:30 pm
Location: KY
Has thanked: 594 times
Been thanked: 597 times

Re: RC10 Factory Works MIP 93' Worlds Racer Restoration

Post by romulus22 »

Looking awesome Todd. You're holding it with the wrong hand though :D

User avatar
RC10resto
Super Member
Posts: 2914
Joined: Tue Sep 09, 2008 2:26 am
Location: Los Angeles, CA
Has thanked: 999 times
Been thanked: 396 times

Re: RC10 Factory Works MIP 93' Worlds Racer Restoration

Post by RC10resto »

Should the antenna mount be screwed to the shock tower?
Looks like you have it on the bulkhead?
Not sure just asking - car looks great.

Vintagemishal
Approved Member
Posts: 502
Joined: Wed Sep 23, 2009 1:51 pm
Location: Portland, OR
Been thanked: 3 times

Re: RC10 Factory Works MIP 93' Worlds Racer Restoration

Post by Vintagemishal »

RC10resto wrote:Should the antenna mount be screwed to the shock tower?
Looks like you have it on the bulkhead?
Not sure just asking - car looks great.
The bulkhead is the original to the car and there was a glue stain on the top where I remounted the antenna base. Not sure how it could be mounted to the shock tower?

Vintagemishal
Approved Member
Posts: 502
Joined: Wed Sep 23, 2009 1:51 pm
Location: Portland, OR
Been thanked: 3 times

Re: RC10 Factory Works MIP 93' Worlds Racer Restoration

Post by Vintagemishal »

romulus22 wrote:Looking awesome Todd. You're holding it with the wrong hand though :D
I was not holding the car, I was holding the camera, but it appears you might be right! :lol:

User avatar
RC10resto
Super Member
Posts: 2914
Joined: Tue Sep 09, 2008 2:26 am
Location: Los Angeles, CA
Has thanked: 999 times
Been thanked: 396 times

Re: RC10 Factory Works MIP 93' Worlds Racer Restoration

Post by RC10resto »

Vintagemishal wrote:
RC10resto wrote:Should the antenna mount be screwed to the shock tower?
Looks like you have it on the bulkhead?
Not sure just asking - car looks great.
The bulkhead is the original to the car and there was a glue stain on the top where I remounted the antenna base. Not sure how it could be mounted to the shock tower?
looks like a shock tower cap screw is going right thru the side of the antenna mount?

Post Reply

Create an account or sign in to join the discussion

You need to be a member in order to post a reply

Create an account

Not a member? register to join our community
Members can start their own topics & subscribe to topics
It’s free and only takes a minute

Register

Sign in

  • Similar Topics
    Replies
    Views
    Last post
  • RC10 FACTORY WORKS MIP 93 WORLDS RACER
    by hugger19 » » in RC10 Buggy Forum
    45 Replies
    6512 Views
    Last post by Beatnik
  • Factory Works Composite Craft Worlds Cheater RC10T build
    by Lavigna » » in RC10 Truck Forum
    15 Replies
    3976 Views
    Last post by scr8p
  • RC10 Worlds restoration
    by oldschoolrc10 » » in RC10 Buggy Forum
    1 Replies
    433 Views
    Last post by juicedcoupe
  • Rc10 worlds racer
    by Proc1973 » » in RC10 Re-Release Forum
    1 Replies
    1304 Views
    Last post by RCveteran
  • RC10 Worlds restoration project (update 5-20-13)
    by mikea96 » » in RC10 Buggy Forum
    37 Replies
    2937 Views
    Last post by scr8p
  • RC10 Factory Works C2 "Tuber" Build
    by NomadRacer » » in RC10 Buggy Forum
    115 Replies
    19705 Views
    Last post by NomadRacer
  • Alcyon's RC10 Worlds Car modern racer build
    by alcyon » » in RC10 Re-Release Forum
    13 Replies
    3450 Views
    Last post by alcyon
  • RC10 Scratch Build - Modernized "Factory Team" Worlds (pics)
    by InceptorOne » » in RC10 Buggy Forum
    5 Replies
    1610 Views
    Last post by InceptorOne

Return to “RC10 Buggy Forum”

Who is online

Users browsing this forum: No User AvatarAmazon [Bot], No User AvatarSemrush [Bot] and 33 guests