Trans or Spur Gear problems Looking for help

General discussion, builds/restorations, etc...

Moderators: scr8p, klavy69

Post Reply
smahoney1
Regular Member
Posts: 28
Joined: Tue Jun 27, 2017 1:32 pm
Location: Wauconda IL

Trans or Spur Gear problems Looking for help

Post by smahoney1 »

I recently installed a Castle Sidewinder 3 4600kv brushless combo with a SMC 2s lipo battery. I went through about half a charge when I started having problems. I would hit the throttle and nothing, just winding up. When I checked the motor, trans, etc. there were black shavings all over the spur gear. See photos in the attachment below. I took off the spur gear and inspected around and in the trans holes that I could see without taking anything apart. Everything looks ok besides the spur gear. I wiped everything down, reinstalled, and tightened the differential spring/nut all the way. I took a few passes and all seemed ok until a part of the steering assembly broke. Should I replace the spur gear and bearings in the spur gear? Any other parts I should consider replacing? What are the black shavings, is that from the old bearings?

https://www.dropbox.com/sh/l9e26gvro6ts0h3/AABPr8r9VbszKwglz6NqbBxya?dl=0

User avatar
jwscab
Super Member
Posts: 6479
Joined: Wed Jan 28, 2009 9:42 am
Location: Chalfont, PA
Has thanked: 10 times
Been thanked: 434 times

Re: Trans or Spur Gear problems Looking for help

Post by jwscab »

That's a lot of motor on a 6 gear and the spur is melted around the diff balls. That diff was slipping quite a bit and overheated.

You'll need a new spur. Likely need diff balls and rings also.

smahoney1
Regular Member
Posts: 28
Joined: Tue Jun 27, 2017 1:32 pm
Location: Wauconda IL

Re: Trans or Spur Gear problems Looking for help

Post by smahoney1 »

Thanks for the reply. Should I search for a matching spur gear or switch to another tooth?

User avatar
jwscab
Super Member
Posts: 6479
Joined: Wed Jan 28, 2009 9:42 am
Location: Chalfont, PA
Has thanked: 10 times
Been thanked: 434 times

Re: Trans or Spur Gear problems Looking for help

Post by jwscab »

depending on the current spur pinion ratio, you might want to run some calculations and see if there is a better ratio to run. at 4600kv I think that motor is something between a 10.5 and 9.5 turn motor. So look at gearing charts, and bear in mind the 6 gear trans internal ratio is 1.86.

honestly i would be really careful with that combo. you might end up wasting diff's continuously since there is no slipper.

User avatar
Lonestar
Approved Member
Posts: 4270
Joined: Wed Dec 12, 2007 5:17 am
Location: Switzerland, yannow, in Europe (or almost)
Has thanked: 620 times
Been thanked: 165 times

Re: Trans or Spur Gear problems Looking for help

Post by Lonestar »

that's a lot of motor to run on that poor 6G trans. You need a perfectly built diff to withstand this amount of modern power (even though it's mild by modern race motor standards). It could slip due to the absence of slipper, or just because it isn't built 100.00% properly.

What's that black grease residue on the spur? What did you grease it with? It won't solve your problem to use the right silicone lube, but if you use what I think you're using ie graphite grease on the balls, you will keep slipping and toasting the spur regardless of what mill you use.

Honestly, ball diff management is like voodoo... and if there's no slipper, it becomes disastrous pretty quickly.

rebuild the diff as per instructions with new parts and get a milder mill :)
AE RC10 - Made In The Eighties, Loved By The Ladies.
Blue Was Better - now, Blue Is Bankrupt.
Facebook affiliate program manager: "They go out and find the morons for me".
Life is short. Waste it wisely.

smahoney1
Regular Member
Posts: 28
Joined: Tue Jun 27, 2017 1:32 pm
Location: Wauconda IL

Re: Trans or Spur Gear problems Looking for help

Post by smahoney1 »

Thanks for the tips. I'm not sure what grease was used when it was originally installed. I will work on replacing all of the parts with new per the instructions and go from there. What is 'milder mill'

User avatar
NomadRacer
Approved Member
Posts: 1467
Joined: Sun Apr 16, 2017 7:29 am
Location: Eastern Shore of Virginia
Has thanked: 83 times
Been thanked: 77 times

Re: Trans or Spur Gear problems Looking for help

Post by NomadRacer »

smahoney1 wrote: Thu Oct 05, 2017 11:08 am Thanks for the tips. I'm not sure what grease was used when it was originally installed. I will work on replacing all of the parts with new per the instructions and go from there. What is 'milder mill'
"milder mill" means a less powerful motor. Get you something like a brushless 17.5. The 6-gear transmission, with a properly built/set up diff. should be able to handle that (with the right spur/pinion).
Bum on Direct Deposit

User avatar
Lonestar
Approved Member
Posts: 4270
Joined: Wed Dec 12, 2007 5:17 am
Location: Switzerland, yannow, in Europe (or almost)
Has thanked: 620 times
Been thanked: 165 times

Re: Trans or Spur Gear problems Looking for help

Post by Lonestar »

Softer motor ;)
AE RC10 - Made In The Eighties, Loved By The Ladies.
Blue Was Better - now, Blue Is Bankrupt.
Facebook affiliate program manager: "They go out and find the morons for me".
Life is short. Waste it wisely.

smahoney1
Regular Member
Posts: 28
Joined: Tue Jun 27, 2017 1:32 pm
Location: Wauconda IL

Re: Trans or Spur Gear problems Looking for help

Post by smahoney1 »

Thanks again for the replies. Should I replace the spur gear with Team Associated #6634 81T and Team Associated #6626 1/8" differential balls?
Again I have a Castle Sidewinder 3 4600kv brushless combo.

User avatar
jwscab
Super Member
Posts: 6479
Joined: Wed Jan 28, 2009 9:42 am
Location: Chalfont, PA
Has thanked: 10 times
Been thanked: 434 times

Re: Trans or Spur Gear problems Looking for help

Post by jwscab »

I'd get whatever gear combo is inexpensive and readily available, and get a few sets in one shot. you might consider getting some tires that have limited traction, this way the 'slip' will be at the wheels, hopefully preventing more meltdowns. Also tune back your esc/motor combo to give you a soft start.

smahoney1
Regular Member
Posts: 28
Joined: Tue Jun 27, 2017 1:32 pm
Location: Wauconda IL

Re: Trans or Spur Gear problems Looking for help

Post by smahoney1 »

Thanks. I ordered another set of wheels/tires and will tone down my esc for a softer takeoff.

Post Reply

Create an account or sign in to join the discussion

You need to be a member in order to post a reply

Create an account

Not a member? register to join our community
Members can start their own topics & subscribe to topics
It’s free and only takes a minute

Register

Sign in

  • Similar Topics
    Replies
    Views
    Last post

Return to “RC10 Buggy Forum”

Who is online

Users browsing this forum: No registered users and 28 guests