Search found 66 matches

by 66intheSky
Sun Feb 13, 2011 8:11 am
Forum: RC10 Truck Forum
Topic: RPM #7027 RC10T Rear Carrier Bearing Width?
Replies: 5
Views: 1052

Re: RPM #7027 RC10T Rear Carrier Bearing Width?

Got the 1/4 x 1/2 bearings from AVID, and they fit perfectly....
by 66intheSky
Sun Feb 13, 2011 8:08 am
Forum: RC10 Truck Forum
Topic: RC10T rebuild, but a question about RPM 8012 steering...
Replies: 6
Views: 1327

Re: RC10T rebuild, but a question about RPM 8012 steering...

Thanx guys.....yea an #3325 8-32 x 1 1/4" would do it for both sides, but is that what RPM recommends you use? Also, are the 3325's blue now? I'd rather not buy them and they be shown gold and get blue ones.... I ordered a pack of the 7/8" screws from RC Planet a few months ago, and they ...
by 66intheSky
Sat Feb 12, 2011 9:25 am
Forum: RC10 Truck Forum
Topic: RC10T rebuild, but a question about RPM 8012 steering...
Replies: 6
Views: 1327

Re: RC10T rebuild, but a question about RPM 8012 steering...

Thanx guys.....yea an #3325 8-32 x 1 1/4" would do it for both sides, but is that what RPM recommends you use? Also, are the 3325's blue now? I'd rather not buy them and they be shown gold and get blue ones....
by 66intheSky
Sat Feb 12, 2011 4:38 am
Forum: RC10 Truck Forum
Topic: RC10T rebuild, but a question about RPM 8012 steering...
Replies: 6
Views: 1327

RC10T rebuild, but a question about RPM 8012 steering...

Hey guys, Just tried to install this RPM 8012 steering kit on my 10T, but the center tubes are loose over the stock 7306 nose screws and the right side screw is too short for a nut on top. I dont have the instructions (if there were any) or packaging cause I bought em off the bay. Are you supposed t...
by 66intheSky
Sat Feb 05, 2011 6:26 pm
Forum: RC10 Truck Forum
Topic: RPM #7027 RC10T Rear Carrier Bearing Width?
Replies: 5
Views: 1052

Re: RPM #7027 RC10T Rear Carrier Bearing Width?

Sweet....thanks again guys 4 ur help.

Acon: I'm using a MIP 1/4" 10T Shiny CVD kit between the new bearings & RPM carriers so I'll be using those shims I guess...

Later dudes :D
by 66intheSky
Sat Feb 05, 2011 4:11 pm
Forum: RC10 Truck Forum
Topic: RPM #7027 RC10T Rear Carrier Bearing Width?
Replies: 5
Views: 1052

RPM #7027 RC10T Rear Carrier Bearing Width?

Hey dudes, Just wondering if anybody could tell me exactly what the width of these bearings needs to be for these carriers. The stock 10T carrier bearings are 1/8 wide, but nobody seems to make 1/4 id x 1/2 od x 1/8 wide bearings for RC applications, only 3/16 wide. Anybody who has these carriers in...
by 66intheSky
Fri Jan 28, 2011 3:42 am
Forum: Losi Forum
Topic: A&L Powerclutch question
Replies: 6
Views: 1010

Re: A&L Powerclutch question

They are 6-32, 1st line in instructions say to put the 6/23 set screw into the top shaft of the tranny. Our Power Clutch for the losi Tranny comes with a new top shaft drilled and tapped for the 6/32 set screw. Sorry I did not answer sooner have not been here in a while. You guys are more then welc...
by 66intheSky
Tue Jan 25, 2011 3:13 am
Forum: Losi Forum
Topic: Losi Slipper Spur question...
Replies: 34
Views: 3324

Re: Losi Slipper Spur question...

Where did you get your Double slipper conversion? thanks, You can convert the single slipper to a dual slipper using the A3111 XX Double Disc Slipper Conversion Kit. I believe that goes for any car using the A3120 (JRX2/T) or A3060 (XX) Slipper shafts. Someone please correct me if I am wrong about ...
by 66intheSky
Sun Jan 23, 2011 8:23 am
Forum: Losi Forum
Topic: A&L Powerclutch question
Replies: 6
Views: 1010

Re: A&L Powerclutch question

I'm under the impression LOSI A-6302 5-40 nuts will fit. Nope. Have a new package of em and tried one, no go. I thought that too and ordered some, but no go. HELP! :o Seems like the long set screw on the A&L is a different diameter or thread pitch than the Losi long set screw included with the ...
by 66intheSky
Sat Jan 22, 2011 11:01 am
Forum: Losi Forum
Topic: A&L Powerclutch question
Replies: 6
Views: 1010

A&L Powerclutch question

Anyone know the size of the nylock nut (A&L No. 289) that fits this slipper? I need some new ones...



1.jpg
A&L JRX2 Powerclutch Instructions and Parts Listing.jpg
Thanks :)
by 66intheSky
Sat Jan 22, 2011 9:50 am
Forum: Losi Forum
Topic: Losi Slipper Spur question...
Replies: 34
Views: 3324

Re: Losi Slipper Spur question...

No I'd rather go single disc because I have everything but an 82T 48P spur and a thrust bearing for it...
by 66intheSky
Sat Jan 22, 2011 2:49 am
Forum: Losi Forum
Topic: Losi Slipper Spur question...
Replies: 34
Views: 3324

Re: Losi Slipper Spur question...

Only one problem guys: I can't find those losi spurs anywhere (a3906 etc), and the thrust bearing a3125 is discontinued. Anyone know the newer p/n's for these or possible subs?

Thanks
by 66intheSky
Thu Jan 20, 2011 5:03 am
Forum: Losi Forum
Topic: Jrx2 cleanup
Replies: 23
Views: 2032

Re: Jrx2 cleanup

I have two Jrx2s that both have no-stamp motor plates, but have the usual rear tower with the holes.... only one of those cars has the aluminium spacers on the gearbox outputs.... confusing! :mrgreen: I also have one with no stamp, but holes on the R shock tower, and alum spacers on the outputs.......
by 66intheSky
Wed Jan 19, 2011 10:27 am
Forum: Losi Forum
Topic: Losi Slipper Spur question...
Replies: 34
Views: 3324

Re: Losi Slipper Spur question...

Thanks again guys awesome info...
by 66intheSky
Tue Jan 18, 2011 3:39 am
Forum: Losi Forum
Topic: Losi Slipper Spur question...
Replies: 34
Views: 3324

Losi Slipper Spur question...

Hey Guys, I'm converting my JRX2 to have a slipper (as in the A3110 Friction Slipper setup) and will soon have all the parts listed, but I need to know what Losi spur gear P/N's can I use on it, because the spur listed in the instructions (A3906) is long gone. I guess the newer double disc slipper s...

Go to advanced search