Search found 124 matches

Return

by dinglem
Wed Oct 10, 2018 8:11 pm
Jump to forum
Jump to topic

AYK Pro Radiant spares - THE MOTHERLOAD

So having built up my Pro Radiant kit a while ago now, I have been scouring the internet trying to locate a few spares to enable me to subsequently race it on the track without having to tiptoe around.... pretty impossible as spares are super scarce as it is in the USA, let alone over in the UK wher...
by BooGTS
Mon Oct 15, 2018 1:35 pm
Jump to forum
Jump to topic

Re: Anyone tried this? Yellowed parts white

I tried this with my AE parts. Used a UVA light, incandescent. This is after ~16 hours. The gear is for comparison. I'm pretty pleased. They don't seem brittle or have their strength affected in any way. I put them in a heat resistant glass over the light, and put a loosely fitted lid on. The peroxi...
by jbmeyer13
Wed Nov 21, 2018 1:31 pm
Jump to forum
Jump to topic

Re: After 4-yrs...my '91 Stealth has begun

Shocks are done so onto the wheels. Yoko TR32 and TF320; also found an additional set of new TR32 tires buried in my parent's basement;-)

Image
by 1966blacktubt
Sat Nov 24, 2018 10:55 pm
Jump to forum
Jump to topic

Cliff lett build

20181103_234013.jpg 20181103_234838.jpg 20181104_004120.jpg 20181104_171544.jpg 20181122_011808.jpg 20181111_100249.jpg 20181104_171552.jpg 20181111_100253.jpg 20181111_100304.jpg 20181122_011756.jpg My cliff lett build took approximately a month to do body was also painted by myself and not farmed...
by scr8p
Thu Jan 10, 2019 4:17 am
Jump to forum
Jump to topic

Re: Scr8p's Worlds Rere #6 / Modern Pavidis Replica - '95 Reedy International

No huge update on this. But I did find some modern tires that mimic the look of the yoke tires that Mark ran. Proline Slide Jobs.

Image
by GoMachV
Sun May 17, 2020 3:36 pm
Jump to forum
Jump to topic

Re: The Official "What is it?" Thread

Those are Traxxas buckles- sold in sets and also individually by length
by Lowgear
Sun Aug 02, 2020 12:30 am
Jump to forum
Jump to topic

Re: Forum News & Discussion

Today I registered ultrarc.net and rc10talk.net to compliment our existing .com variants. They both redirect you to here. It's always a good idea to register the other top-level domain name extensions of your main one when available. A few of you may remember that way back in 2002 I had an R/C monst...
by Ruffy
Mon Sep 07, 2020 4:12 pm
Jump to forum
Jump to topic

Re: My Curtis Edinger Restoration-The one that ALMOST got away

A little more progress last night and today.

Image

Image
by radioactivity
Thu Sep 10, 2020 12:59 am
Jump to forum
Jump to topic

Re: RPS Yokomo YZ-834B

If you think you know little about Yokomo, I know far far less. Almost nothing. However, the motor, you might need to talk to coxbros1 as he has a couple of them. Brushes may be difficult to find. The Funco/Bolink body, Dan is the Man. Sabulatech has numerous Bolink molds and https://store.sabulatec...
by RC10resto
Thu Sep 10, 2020 2:00 am
Jump to forum
Jump to topic

Re: RPS Yokomo YZ-834B

Nice early hopped up 834B 8)
Pre RPS SE car.
Lot's of Delta influence.
Kyosho CB88 shocks, much bigger than Scorpion.
Many rare parts :!:

I hope you plan to restore it as is, just clean it up and fix broken parts.
by a01butal
Thu Sep 10, 2020 12:10 pm
Jump to forum
Jump to topic

Re: RPS Yokomo YZ-834B

Duckhead, check your pm's.
by AscotConversion
Sat Sep 12, 2020 11:36 pm
Jump to forum
Jump to topic

Re: RPS Yokomo YZ-834B

Slot car brushes should fit the Checkpoint motor - most any slot car track should be able to help you.
by Ruffy
Mon Oct 26, 2020 2:03 am
Jump to forum
Jump to topic

Re: Have you noticed...

I do believe the reason for the two holes in the motor plates backside is for tooling, to hold it in the jig while the press comes down to create the two bends. Basically the two holes were for dowels to hold the plate firmly while the press comes down and bends the motor plate at 90 degrees and als...
by GoMachV
Mon Nov 30, 2020 3:33 am
Jump to forum
Jump to topic

RIP Jim Halsey

Just saw posted on Facebook that one of the legends has passed :(

RIP Jim Halsey