I got a tip regarding a Junior T for a reasonable price and from a neighbour country here in Europe.
I bought it thinking it would be a nice pile of parts.
It turns out the truck has never been run. Not a scratch anywhere.
I guess it is a late...
Last post
I contacted TBG regarding the Junior T body. It turns out they had stopped making it due to supply shortage for the specific Lexan needed.
However they managed to make me a body using a different material. Big thanks to Trish and Jon! 8)
MCI...
I'm looking for a Tamiya paint code for the blue on the box art for the Losi Jr-2, Junior 2. Looks like a metallic blue , maybe?
Any help will be appreciated.
Thanks
Last post
This wing is painted in Duratrax metallic blue, backed in metallic silver.
Well,it's all done,apart from a few touch ups and some decals I need to slap on.
Not bad for a test body .
It's a Team Bluegroove body,I came across and bought a genuine NIP Losi body while this body was all masked up,so I thought I might as well...
Here's my LX-T that I raced on carpet ovals as a kid. It's close to how it was back then, except for the .36 shocks and yellow motor plate.
I ran A&L Roadkill & BTS Liberator, Dahm's Ruff- E-Nuff SE and Andy's Lo Profile bodies. I had Trinity...
Last post
Well... it's a cream dream. Probably my favorite yet. 8) Seriously.
I found these aluminum uprights for a XXX_SCT and was wondering how their geometry compared to the XXX. AS in, if the caster and spacing were the same. Any ideas?
I gather the SCT kingpin is longer?
I just picked up a XXX BK1 for no good reason...
Last post
Never mind: the pins are all 1/8 , vs the 3/32 on the buggy.
Any suggestions on replacement Jrx2 rear tires? Seems like there have been a few 2.0” tires available in the past, but nothing currently. I’d prefer some 4 rows like the originals but would settle for almost anything that looks like it came from...
Last post
Here are some more Tamiya 2 tires.. 50344 spike, 53059 stud spike & 50269 oval block/spike
Never seen this before and have had a lots of them. Triangle center? I could see how it would create less friction yet still support at this common area for melting?
Last post
I'd like to start an official conspiracy theory on this. Needs to be a vintage one rooted in 1990 give or take.
After building my Jrx2 series buggies and setting aside parts for another build or two, I still have a decent sized pile of used Losi parts. So I have decided to take the worst parts that are still functional…you know..the scratched, faded, rusty,...
Last post
I have been driving this truck a lot and decided to make it not quite so ugly with a body upgrade.
Really nothing special here, but all these years later my wife came across these old pictures of mine. This car was my younger brothers that I built for him back then. Thinking back to when we built it I could have sworn it came with red logo wheels...
Last post
At the time it would be weird maybe, but with benefit of hindsight now would be cool to have recevied a we're using up spare parts kit. AE did it too with the RC10's. If you had one today you could get everyone on FB arguing about it and then put it...
I know this model is right on the edge of vintage, but it's Kinwald so it automatically gets a pass. :lol: I have been saving up cool and rare XXX parts for several years because I knew I would eventually build some sort of XXX car. I finally...
Last post
Incredible build! I mistakenly commented on your gallery post but I'm in awe of your collection! I remember always drooling over Brian's cars back in the day. You've done an amazing job with all of them!
I have been a Team Associated guy for well over 30 years. If you were to hand me a pile of parts from any of the old Associated cars, buggies, or trucks, then I could correctly identify and assemble all of them...
Last post
McAllister #135 Ford Truck Body 1/10
Wow that is cool! Thanks for the info!
The body I posted above is on the way to another member already :mrgreen:
I have an xxx4 front diff that is completely missing out of car and its been slow to find one. From what I read the xxx-s shares very little with the xxx4 but are the diffs the same? Is there any other diffs out there that could be substituted off...
Last post
Welp, it seems like I no longer have the xxx-s as I cannot find it. I still have the jrx-s but yeah...day and night differences there. Once all the dust cleared I had bought the one from valkarie one and an hour later received a PM from Spain that...
Looking at my Losi Mini-T 1.0 (old rear motor version) I found that if I would stretch this thin a little bit, it would be quit exactly a 3/4-Scale-1/10-Buggy .
With 180 mm instead of 240 mm, according to that the...
I am a fan of the Losi LRM transmission and the upgrades available for it..so this is a cool one. This MIP L-260 kit includes a different top gear and diff gear to change the original LRM ratio from 2.18 to 2.6
Last post
Nice! I put one in my LXT back when I still raced it. And I think I have a backup kit I got years later.
When upgrading the original jrx2 to a pro using the proformance kit what shocks are used in the front? The original short body (.6)? I know the production jrx pro uses a long shock and shaft (.9). There is a post on here with the entire upgrade...
Last post
That was perfect! The box clarifies that there are long shocks used in the proformance kit in the front. Those gold shocks are super nice I have a set on a stellar jrx pro se
So I picked up this used JRX2 a few month ago. It was in decent shape and has a a few pretty nice period hop ups. The 3 piece front wheels are kinda cool. Bottom isn't too gouged up. (ugh stop rotating my pics....)
IMG_20221222_113533309.jpg...
Last post
That has a nice assortment of upgrades…looks good! Thorp top gear too. I might have a set of silver .9 shocks for you…I’ll check the stash later.
Does anyone know if the XX transmission braces with the ears or fingers on them give any extra strength or rigidity to the chassis or transmission compared to the simple little rectangular braces? This will be for a runner build with a modern motor....
Last post
I have only ever broken the ears off the transmission case just behind the holes that screw to the bulkhead. I don't believe either brace really solves that problem (unless others are suffering different failures to me).
Friday I finally got my new project in. The previous owner must have really liked Miller.
Despite the mismatched screws and some maintenance neglect and some incorrect parts like shocks and wheel it was in pretty good shape. Also pretty...
Last post
Going through some stuff i realized I had an extra set of truck threaded shock bodies. The shocks on this car weren't a matching set and on top of that the silver front bodies don't seem to seal up to the newer style of cartridges very well. I...
This is planned to be a high end XX4 with modern electronics, running a 13.5 brushless motor.
This project has been in the pipeline since before I finished my early version XX4 shelfer, several years ago. I have been gathering parts for the past...
Last post
A few final pieces, such as steering link and Dragon aluminum wing mounts.
So the first ever Hobby grade RC I owned was a used Losi JRX Pro SE that my step father helped me purchase when I was a kid. Later I sold it off to help buy a a former racer's LXT and his entire inventory of parts, radios, electronics, and motors,...
Last post
On the Jammin setup there is some bump steer at lockup..the outside more than the inside. I see your outer tie rods are spaced up high. The Jammin only uses 2 washers like mentioned in that Losi Tech Talk.
Hello All! I have a jrx2 plate chassis and it has some small nicks on the edges and ideas on a product or method to repair them for a shelfie. Also maybe a topcoat that can have the same sheen as the original?
Last post
Yeah that does look good! Thank you for the good info
You don’t see much info out there about these…This is from my collection for reference.
Thorp hard anodized aluminum gears.
Early parts:
#5101 left gear
#5102 right gear
#5103 Diff gear
Later they came out with a center bearing diff gear,...
Last post
The Thorp Delrin top shaft gear also fits properly on the Losi A-3120 Hydra-Drive/Slipper shaft. Which means it will also fit the A-3007 JRX-Pro top shaft and the A&L Power Clutch shaft.
I've just done this exactly after I received the...
For some reason, the front wheel nuts don't go past the end of the axle, my OCD dislikes this! I scoured the internet & it appears that they should. The only thing I can think of is that I have the wrong axles. The spindles & wheels are definitely...
Last post
Great info to be had, thanks for confirming the axles being the same, all i had at home were pro axles and xxxt axles.
I have two of these kits…so I decided to open one up, install it on my Pro-SE and see what it’s all about.
The shock tower is the same shape as the original, slightly thicker at 3mm instead of 2.5mm...
Last post
I never changed the front springs on mine when I got it back in the day, I don't think. Might have overlooked it. After reading the insert, I'm not sure I did much beyond putting in the shock tower and LXT uprights, because I don't recall the shims...
I am curious what the main difference between the two chassis's is? I know the wheel base is different but like the XX4 (extra 1/2 that can be noticed when checking between the servo mount and reciever mount or cuts between the cell punchouts )...
Last post
Thats awesome man! Thank you! This answers my question exactly.
Hey, I know it's not vintage enough but I'll try to make it worthy.
Always wanted one of those since I saw a ad for a BK2 in RCCA back in 2006. They are very hard to find here and this one was not bad in the pics so I decided to grab it. I've...
Last post
Not a bad buggy, a great majority of my previous racing was with it's sibling, the XXX-T MF.
It appears you have a regular version of the buggy, the BK version would have all graphite molded parts and threaded shock bodies.
The unique in the World Custom CNC cut Carbon Fibre chassis Losi xxx-s
ı want keep to make original measure on this carbon fibre chassis.
(Bottom side belt tunnel is very unnecessary. so demount the front and rear diff covers sufficient to replace...
Last post
Very cool chassis how much? Lol just joking! but you did do a awesome job. Well done sir
So, I am building/restoring a JRXT. A few questions
The instruction manual - There is a Rev A and B - what are the differences
The battery holder - did it have the original type then switch over to the swing arm?
The steering linkage - Did it only...
Last post
Welp looks like I have a JRXT chassis, Guess I'm making a long JRX2 in my future.
Managed to grab this XXX-NT AD2 on eBay recently. It was complete except for the front chassis brace. The engine is an OS Max 12 TZ. Here are some pictures of what it looked like when it arrived.
IMG_3383 copy.jpg
IMG_3384 copy.jpg
IMG_3418...
Last post
Does anyone know of any modern axle conversion methods for the AD2? I've found some that use the XXX-SCT parts but those are hard to find now as well. I'm just beginning my research now but figured I'd post here to see if anyone has ideas or has had...
Does anyone know if the Losi 3022 gear and gear that comes with Losi 3007 are the same gear?
They look like they are , just not sure?
Last post
For future reference... The A-3022 top shaft gear is also used on the A-3120 Hydra-Drive/Slipper shaft (Pro-SE & LXT) and on the A&L/Factory Works Power Clutch shaft.
Can anyone share any tips or tricks on how they are refinishing their XX era motor guards? Trying to clean up a few runners and wanted to get them looking better. Thanks in advance!
So I’m restoring a JRX2. The chassis I’ve got is decent but needs a bit of tlc. I hit it with fine grit paper and that helped. Anyone do anything else like paint it? Thanks
Last post
Great looking buggy! One of my favorite things about the original Jrx2 is the sleek bumperless front end.
The original idea for this build was a low budget runner using the best used parts from my pile. As with any project, there has already been significant scope creep as visions of big bore shocks, modern tires, and mild brushless power sent me to...
Last post
Old thread I know, but still enjoyed it. Alot of useful info.
With all the fun I'm having with the new mini the bug bit me and I found a 1/10th car. Seems to be a truck conversion from the proformanance era(no servo saver hole). Has anyone put together a list of other sources of parts that will help rebuild...
Last post
There is a lot of interchange across all the vehicles.. The biggest changes were later with the LXT and Retrofit trans but still there were a lot of common parts. Use the manuals at Vintagelosi to help compare the vehicles.
Curious if others no of high offset wheels for the JRXT. Plenty of adapters to make them hex drive but as we all know offset unique. I am aware of all the options of converting to different hubs and such on these for buggy wheels. None of those...
Last post
I have used the aluminum front Tamiya ones I posted on a basher before and they held up to a lot of abuse. Whether they are proper or not I don't know but worked. I seem to recall having them on the front of an RC10 too with the metric bearings,...
(Again) I have tried to collect some information and parts for my next project before making it public. I try to to make this the most important/best project that I will ever make. The project will be Team Losi's Jrx2 Proformance kit prototype car...
Here goes what should be an over the top build. It's not meant to be a replica, or even entirely era accurate. I just want to build what I think is the coolest XX.
I was forced to sell my very special NIB XX Kinwald build earlier this year. I've...
Last post
Oh, nice. Sure haven't heard of that until now, thanks for the lesson!
I've been searching high and low for some 2.0 long, 2.9 rate LOSA5129 Orange springs and can't find anything other than some insanely high price gouge eBay items. Is there something else that might work? Like off of the mini buggies...
Last post
I used Losi springs on a TRX1 back in the day. So I would assume the Traxxas springs would fit the Losi...
This car started out in the late 80s as a standard original JRX2.....me and my brother raced against it at our local tracks quite often back in the 80s....finally acquired it from the original owner. Going to do a full restoration back to original...
Last post
What paint did you use on the chassis? Looks sweet and I’m
Redoing mine.
Filled gaps and holes with jb weld. Sanded it it all smooth. Painted it with black rustoleum or equivalent spray balm and cleared it with cheap automotive clearcoat from...
Users browsing this forum: No registered users and 31 guests
Forum permissions
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot post attachments in this forum
