RC10Talk - The Net's Largest Vintage R/C Community

All - in light of recent prices on EBAY for NIP original OT-30 optima tires (unbelievable! ), I have decided that I will keep the ones that came with my NIB kit unused for the shelf and try to source some cheap alternatives should I decide to run the car.

Can anyone, therefore, recommend some readily (or at least more readily) available tires which fit the original optima rims? I'm looking for full width 4wd spiked tires.....

Thanks in advance.

well, 1.6 tires fit, so you should be able to find some RC10 rear Tires, not readily available per say, but cheaper than $132 lol

i dont think there are any 1.6 tires readily available, unless from tamiya re're's like the frog/buggy champs etc, those are 1.5 but should fit

Change both rim and tires to run....problem solved

uzzi wrote:Change both rim and tires to run....problem solved

Any suggestions, Chris, as to what rims/tires would fit (my knowledge is somewhat limited when it comes to Kyosho)? I'd really like some 5-spoke tires like these perhaps: http://www.tamiyaclub.com/trades_model.asp?cid=85782), but iwould be nterested to know about any other viable alternatives...

I am pretty certain those are HPI 3033 Super Star Wheel 57x35mm...based on those sizes 2.2 tires should fit on them but am uncertain of the offset (looks ok however).

I am pretty hazy with my Kyosho stuff but I think you would find the rims from Optima-Turbo Optima-Optima Mid and rear Ultimas are compatible in offset....they are however in 2 inch sizes (use CAT tires). You could try looking for Trinity wheels to fit 2.2 tires (can't remember the part number)

hotshot re-re tires are planty available

Mr. ED wrote:hotshot re-re tires are planty available

That presumably means those Lohas tecnacraft look-a-likes will fit?......I've been waiting for an excuse to get a set of those...

erh, no

The Lohas are 2.2 inch, but yes you could fit those rims to your optima fur sure and with their adjustable offset they'd be a great choice.

personally i like these tires
http://www3.towerhobbies.com/cgi-bin/wti0001p?&I=LXAHL7&P=7
they are low profile, i have them on my ultima build originally

What about these: http://www3.towerhobbies.com/cgi-bin/wti0001p?&W=000308206&I=TAMC3000&P=K
I read somewhere that they would fit my old Turbo Ultima wheels. But i am not 100% sure.

You are going to run those alloy rims?
Finding tires are not the issue but rims to suit would be.

The wheels and tires off of these vehicles should work?

http://www3.towerhobbies.com/cgi-bin/wti0001p?&I=LXVZB2&P=SM
http://www3.towerhobbies.com/cgi-bin/wti0001p?&I=LXWWR5&P=SM

I run Lazer ZXR/ZX5 rims. They are 2.2inch and allow me to used modern tyres to suit track conditions.

Brandon G wrote:The wheels and tires off of these vehicles should work?

http://www3.towerhobbies.com/cgi-bin/wti0001p?&I=LXVZB2&P=SM
http://www3.towerhobbies.com/cgi-bin/wti0001p?&I=LXWWR5&P=SM

I think the offset on these 2 is too small for the front: probably causing interference between the rim and steering knucle.

The original ZX5 front rims are set out further and work indeed.

bormac wrote:I run Lazer ZXR/ZX5 rims. They are 2.2inch and allow me to used modern tyres to suit track conditions.

Thanks, Bormac. Do you have a link to the wheels you are referring too (my Kyosho knowledge is very limited, I'm afraid)?