Wheel base RC10CE vs Worlds Car

General info, Q&A.

Moderator: scr8p

BACK_AT_IT
Regular Member
Posts: 13
Joined: Sat Oct 03, 2015 4:36 am

Re: Wheel base RC10CE vs Worlds Car

Post by BACK_AT_IT » Sat Mar 31, 2018 4:43 am

Thanks for the info! A couple of questions:
- how would the b3 hub help? Is it set out further than the world’s hub? Hence allowing more room for 9754 cva?
- I think I know what droop is I assume it’s how low you set your shocks
- limiters on shocks? What does this mean.
Thx!

User avatar
TRX-1-3
Approved Member
Posts: 676
Joined: Sat Mar 29, 2014 4:13 pm
Location: Wallowa County, Oregon

Re: Wheel base RC10CE vs Worlds Car

Post by TRX-1-3 » Sat Mar 31, 2018 6:51 am

My......ocd.....compels me..

It's track width.
Hope you're doin' something fun.

R16
Regular Member
Posts: 27
Joined: Thu Nov 23, 2017 4:34 pm
Location: Japan

Re: Wheel base RC10CE vs Worlds Car

Post by R16 » Sat Mar 31, 2018 12:55 pm

>TRX-1-3
Thank you for your correction. I agree that "rear tread" is wrong.

>BACK_AT_IT
I tried the "CVA axle > B3 hub > B4 blue wheel spacer > drive shaft pin > Custom works 1/8 spacer > worlds tire" combo.
B3_hub_1.jpg
Here the CVA bone is #9760. B3 hub has inward offset so that #9760 can work as CVA bone with enough droop.
However, it does not work because the custom works 1/8 inch spacer does not fit to the worlds tire.
It hits the side edges of the tire shown by red arrows.
B3_hub_2.jpg
I am sorry.

User avatar
klavy69
Moderator
Posts: 5847
Joined: Thu May 29, 2008 8:11 pm
Location: Fulton, IL (Land of one stop light but we DO have a windmill!)

Re: Wheel base RC10CE vs Worlds Car

Post by klavy69 » Sat Mar 31, 2018 5:47 pm

so would the simple removing of the outerside edge of the circle of the worlds wheel with a dremel work or am I reading too much into this?

Todd
Peace and professionlism.....Kabunga signing off!!!

User avatar
jwscab
Approved Member
Posts: 5676
Joined: Wed Jan 28, 2009 2:42 pm
Location: Chalfont, PA

Re: Wheel base RC10CE vs Worlds Car

Post by jwscab » Sat Mar 31, 2018 6:04 pm

Yeah slight tweak on the wheel slots and you are golden. Don't be sorry, this looks like it will.work nicely if you have enough thread engagement on the nut.

BACK_AT_IT
Regular Member
Posts: 13
Joined: Sat Oct 03, 2015 4:36 am

Re: Wheel base RC10CE vs Worlds Car

Post by BACK_AT_IT » Wed Apr 11, 2018 12:26 am

The B3 hub (and I even found a set at my local hobby shop) looks like it will work with the original Worlds Car CVAs. I can see that I won't need to have extreme camber or limit my droop a lot with these hubs.
Thanks for your help everyone!

Timmahhh
Approved Member
Posts: 182
Joined: Tue Feb 07, 2012 6:57 pm
Location: IL

Re: Wheel base RC10CE vs Worlds Car

Post by Timmahhh » Wed Apr 11, 2018 5:03 pm

klavy69 wrote:
Sat Mar 31, 2018 5:47 pm
so would the simple removing of the outerside edge of the circle of the worlds wheel with a dremel work or am I reading too much into this?

Todd
Or if the setup will be used with a lot of wheels, file/dremel off the ends of the ridge on the spacer so it fits into the wheel

Post Reply

Return to “Temple's RC10 Tech Forum”

Users browsing this forum: No registered users and 3 guests