*Parts needed to run modern 2.2 rims/tires on your rc10*

General info, Q&A.

Moderators: scr8p, klavy69

mark in wi
Approved Member
Posts: 58
Joined: Mon Aug 15, 2011 12:58 pm

Re: *Parts needed to run modern 2.2 rims/tires on your rc10*

Post by mark in wi »

RC104ever wrote:Can you post a pic of how the fuel tubing was used?
Not sure how he did it. You cut a small piece and fit into the "cup" of the axle and outdrive. This stops the dog bone from going to the bottom of one side and falling out of the other. I think I used a piece of a foam earplug to get the same effect.
Hope this helps/makes sense.

Mark

User avatar
JK Racing
Approved Member
Posts: 4599
Joined: Thu Jul 19, 2007 2:32 pm
Location: Placentia, CA
Has thanked: 102 times
Been thanked: 192 times

Re: *Parts needed to run modern 2.2 rims/tires on your rc10*

Post by JK Racing »

wrong forum :oops: :oops:
--Joey --
Vintage A&L and Factory Works
Old School Racer & Vintage RC Car nut
JKRacingRC.com

CUDDZILLA
Approved Member
Posts: 85
Joined: Sat Dec 10, 2011 12:51 am

Re: *Parts needed to run modern 2.2 rims/tires on your rc10*

Post by CUDDZILLA »

Does anyone know if you can adapt touring car wheels(hex drive) to fit the rc10? Anybody? Bueller?

User avatar
RC104ever
Approved Member
Posts: 1506
Joined: Sun May 22, 2011 11:34 am
Location: Burlington, Ontario - Canada
Been thanked: 8 times

Re: *Parts needed to run modern 2.2 rims/tires on your rc10*

Post by RC104ever »

I don't know about touring car wheels, but here is how to do HPI hex drive wheels:

http://www.rc10talk.com/viewtopic.php?f=35&t=20904&hilit=+hpi+star
- Chris
Lots of cars...so many cars

User avatar
rc10johnny
Approved Member
Posts: 1304
Joined: Sun Sep 27, 2009 6:48 pm
Location: Richmond Va.
Been thanked: 1 time

Re: *Parts needed to run modern 2.2 rims/tires on your rc10*

Post by rc10johnny »

SC10 Hex...... :shock: :mrgreen: Image

User avatar
rc10johnny
Approved Member
Posts: 1304
Joined: Sun Sep 27, 2009 6:48 pm
Location: Richmond Va.
Been thanked: 1 time

Re: *Parts needed to run modern 2.2 rims/tires on your rc10*

Post by rc10johnny »

Image

User avatar
rc10johnny
Approved Member
Posts: 1304
Joined: Sun Sep 27, 2009 6:48 pm
Location: Richmond Va.
Been thanked: 1 time

Re: *Parts needed to run modern 2.2 rims/tires on your rc10*

Post by rc10johnny »

Image

mark in wi
Approved Member
Posts: 58
Joined: Mon Aug 15, 2011 12:58 pm

Re: *Parts needed to run modern 2.2 rims/tires on your rc10*

Post by mark in wi »

So what parts did you use to get the sc10 hex to work? Looks nice. How well does it work?

User avatar
rc10johnny
Approved Member
Posts: 1304
Joined: Sun Sep 27, 2009 6:48 pm
Location: Richmond Va.
Been thanked: 1 time

Re: *Parts needed to run modern 2.2 rims/tires on your rc10*

Post by rc10johnny »

mark in wi wrote:So what parts did you use to get the sc10 hex to work? Looks nice. How well does it work?
all associated except rhe 1/8 drill bit....caster block#7922..steering block# 9880....front axel#9881...3/16X3/8 bearings...$16.00...Proline makes a kit for $29.95...JohnnySr

User avatar
toyranosaur
Business Member
Posts: 233
Joined: Thu Jul 03, 2008 8:50 am
Location: USA
Been thanked: 1 time

Re: *Parts needed to run modern 2.2 rims/tires on your rc10*

Post by toyranosaur »

Maybe some Technacraft-style wheels that are slightly bigger bead depth? Then just bolt 'em on? Thoughts? Chris REC

mark in wi
Approved Member
Posts: 58
Joined: Mon Aug 15, 2011 12:58 pm

Re: *Parts needed to run modern 2.2 rims/tires on your rc10*

Post by mark in wi »

Last night I was wondering if my CVDs from my tc3 would work since I have broken dog bone. I took everything off my rc10 and then the tc3. The bearings drooped right in! The "drive shaft" part was too short but the axel fit nicely. I took the Hexs and they seemed like they will work perfectly. Needless to say I could not try it out but it might help someone.
Mark

User avatar
Phin
Approved Member
Posts: 2714
Joined: Tue Feb 21, 2012 5:17 pm
Location: NY²
Has thanked: 59 times
Been thanked: 162 times

Re: *Parts needed to run modern 2.2 rims/tires on your rc10*

Post by Phin »

hairymuffin wrote:best thisng is using the hex instead of the pin,no stripped out wheels.. I added a green spacer on the hub,can be tuned to run the hubs forward or aft...Another good thing which was most important to me is that the cvd fits in the outdrive perfectly in the middle..Going to the track today to try it out guys
davidka wrote:Muffin, what's the track width of that compared to stock? Nice find.

Didn't see an answer to this questions...do the Kyosho hubs and CVDs change the track width at the rear?

18ri
Regular Member
Posts: 10
Joined: Tue Aug 14, 2012 2:38 pm
Has thanked: 1 time

Re: *Parts needed to run modern 2.2 rims/tires on your rc10*

Post by 18ri »

I put the B4 rear stub axle in an old RC10 by changing out the bearings. Then I installed the B4 rear wheels. Only problem is the B4 wheels have a greater offset than the RC10 wheels so the rear is now narrower than the RC10. Anyone else have this problem, and how did you get around it?

Thanks

fredswain
Approved Member
Posts: 1167
Joined: Fri Mar 11, 2011 4:20 pm
Location: Houston
Been thanked: 4 times

Re: *Parts needed to run modern 2.2 rims/tires on your rc10*

Post by fredswain »

Go back to the first page of this thread and start reading. There are various methods listed.
Raborn Racing Originals Shapeways store

KHShapiro
Regular Member
Posts: 18
Joined: Fri Mar 01, 2013 11:58 pm
Location: Wichita, KS

Re: *Parts needed to run modern 2.2 rims/tires on your rc10*

Post by KHShapiro »

In the fronts i am using Blitz front hub assembly for use of hex on the fronts. On the rears I'm using Blitz (generation 1) rear axels and bearing in the stock RC10 hubs. I pressed in the bearings flush on the inside and outside . I used the hip blitz stuff because I had it on hand and it fit.

Post Reply

Create an account or sign in to join the discussion

You need to be a member in order to post a reply

Create an account

Not a member? register to join our community
Members can start their own topics & subscribe to topics
It’s free and only takes a minute

Register

Sign in

  • Similar Topics
    Replies
    Views
    Last post
  • Modern rims/tires for vintage RC10 or how I gave up on old tires
    by Nero45 » » in Temple's RC10 Tech Forum
    8 Replies
    3004 Views
    Last post by XLR8
  • New/modern tires that will fit narrow front 10T rims?
    by AndrewSi » » in RC10 Truck Forum
    1 Replies
    844 Views
    Last post by Charlie don't surf
  • RC10 Buggy Can I run modern B4 wheels?
    by ffpm46 » » in RC10 Buggy Forum
    3 Replies
    784 Views
    Last post by fastang
  • Need help on parts needed for truck tires!
    by Jman115 » » in Temple's RC10 Tech Forum
    8 Replies
    1184 Views
    Last post by aconsola
  • Need new rims and tires for original RC10
    by veghead211 » » in RC10 Buggy Forum
    6 Replies
    1168 Views
    Last post by veghead211
  • rc10 modern parts listing
    by JosephS » » in R/C Off-Topic / Chit-Chat
    2 Replies
    415 Views
    Last post by JosephS
  • rc10 ds modern wheel conversion parts
    by Luckyracing » » in Associated On-Road Forum
    3 Replies
    1378 Views
    Last post by jwscab
  • Lohas rims and what's needed
    by bow2986 » » in RC10 Buggy Forum
    7 Replies
    1248 Views
    Last post by bow2986

Return to “Temple's RC10 Tech Forum”

Who is online

Users browsing this forum: No registered users and 17 guests