Composite Plastic Chassis Restoration

When it's R/C related, but doesn't fit anyplace else.

Moderators: scr8p, klavy69

Post Reply
User avatar
duckhead
Approved Member
Posts: 446
Joined: Fri Nov 06, 2015 12:41 pm
Location: Minooka, IL
Has thanked: 78 times
Been thanked: 86 times

Composite Plastic Chassis Restoration

Post by duckhead »

Has anyone had any experience removing scratches or small gouges from composite plastic chassis, specifically of the B2/B3 variety?

If so, what method(s) did you find yield the best result?

IMG_7482.jpg

Thanks!
->Mark

User avatar
RC10th
Approved Member
Posts: 4209
Joined: Sat Feb 16, 2013 9:51 am
Location: Australia
Has thanked: 36 times
Been thanked: 934 times

Re: Composite Plastic Chassis Restoration

Post by RC10th »

I haven't done but I would guess sand scratches out then polish with automotive polish till it's the same appearance as virgin plastic.
I was old school - when old school wasn't cool !

Dadio
Approved Member
Posts: 3791
Joined: Sun Apr 24, 2016 2:21 pm
Location: Guildford UK
Has thanked: 2145 times
Been thanked: 1915 times

Re: Composite Plastic Chassis Restoration

Post by Dadio »

I've done this on a Team C chassis and sanding out the scratches is easy but don't use polish ! The polish soaks into the plastic and turns white as it drys ,you can't wash out the polish as it soaks in , just sand down with progressively finer wet and dry paper , finishing with a 1600 or above grit . I toyed with a fine dusting of lacquer but did not in the end try it as it was to be run again or you could rub in some silicone grease to give it a little lustre .
If a jobs not worth doing then its certainly not worth doing well.
A problem shared is a problem halved but an advantage shared is no advantage at all.

User avatar
Mr. ED
Approved Member
Posts: 5475
Joined: Thu Dec 21, 2006 1:30 am
Location: Back @ home: Belgium
Has thanked: 58 times
Been thanked: 56 times

Re: Composite Plastic Chassis Restoration

Post by Mr. ED »

Medium blasting?

tamiyadan
Approved Member
Posts: 1690
Joined: Wed Apr 07, 2010 4:45 pm
Been thanked: 6 times

Re: Composite Plastic Chassis Restoration

Post by tamiyadan »

.

User avatar
NomadRacer
Approved Member
Posts: 1467
Joined: Sun Apr 16, 2017 7:29 am
Location: Eastern Shore of Virginia
Has thanked: 83 times
Been thanked: 77 times

Re: Composite Plastic Chassis Restoration

Post by NomadRacer »

Me?

I'd block sand it with silicone carbide sandpaper (black kind) under water. Sand in one direction only. The starting grit would depend on how deep the scratches are. Increase the grit (400,600,etc.) to the level of "shine" you want. Finally, spray with WD40 and rub it in with a microfiber cloth.
Bum on Direct Deposit

User avatar
sandkil
Approved Member
Posts: 1041
Joined: Tue Jan 15, 2013 10:00 am
Location: Stockholm Sweden
Has thanked: 652 times
Been thanked: 458 times

Re: Composite Plastic Chassis Restoration

Post by sandkil »

I tried wet sanding, but not enough as the result shows.
I would vote for media blasting as well.
Attachments
IMG_1692.jpg

Dadio
Approved Member
Posts: 3791
Joined: Sun Apr 24, 2016 2:21 pm
Location: Guildford UK
Has thanked: 2145 times
Been thanked: 1915 times

Re: Composite Plastic Chassis Restoration

Post by Dadio »

The answer is probably to use both graded wet n dry paper to remove the scratches and then media blasting for the correct surface finish .
If a jobs not worth doing then its certainly not worth doing well.
A problem shared is a problem halved but an advantage shared is no advantage at all.

mikea96
Approved Member
Posts: 3238
Joined: Thu Oct 01, 2009 4:34 pm
Location: Puyallup, WA
Has thanked: 146 times
Been thanked: 526 times

Re: Composite Plastic Chassis Restoration

Post by mikea96 »

I sand mine with progressively finer paper then use armorall trim and plastic restorer to bring back the color.
Attachments
20180226_163733.jpg

User avatar
duckhead
Approved Member
Posts: 446
Joined: Fri Nov 06, 2015 12:41 pm
Location: Minooka, IL
Has thanked: 78 times
Been thanked: 86 times

Re: Composite Plastic Chassis Restoration

Post by duckhead »

Started with 360, to 600, and finished with 1500, all wet sanded. Still have some deeper scratches to go, but I was getting disappointed with the result as it seems to be polishing the plastic too much and rounding the sharp lines. Media blasting sounds interesting, I might have to research that a bit. Was also considering getting a finish dual action sander and trying that.

Maybe the polish look will grown on me, and I'll try either WD40 or the Armorall.

More to come...

IMG_7492.jpg

Dadio
Approved Member
Posts: 3791
Joined: Sun Apr 24, 2016 2:21 pm
Location: Guildford UK
Has thanked: 2145 times
Been thanked: 1915 times

Re: Composite Plastic Chassis Restoration

Post by Dadio »

To keep the crisp edges you need a large flat block under the wet and dry paper or ever use course diamond Hone's , they are basically used for sharpening machine tools etc but are very flat metal plates impregnated with industrial diamond dust , great things to have for sharpening anything really from knives to scissors and a good set of 3 only costs £10 , much better than any kitchen sharpener or a wet stone etc .
If a jobs not worth doing then its certainly not worth doing well.
A problem shared is a problem halved but an advantage shared is no advantage at all.

User avatar
NomadRacer
Approved Member
Posts: 1467
Joined: Sun Apr 16, 2017 7:29 am
Location: Eastern Shore of Virginia
Has thanked: 83 times
Been thanked: 77 times

Re: Composite Plastic Chassis Restoration

Post by NomadRacer »

I agree with Dadio. To get the crisp edges you must block sand.
Bum on Direct Deposit

User avatar
RC10th
Approved Member
Posts: 4209
Joined: Sat Feb 16, 2013 9:51 am
Location: Australia
Has thanked: 36 times
Been thanked: 934 times

Re: Composite Plastic Chassis Restoration

Post by RC10th »

Sand different grades in different directions so you know when you've removed your previous sanding marks.
I was old school - when old school wasn't cool !

Post Reply

Create an account or sign in to join the discussion

You need to be a member in order to post a reply

Create an account

Not a member? register to join our community
Members can start their own topics & subscribe to topics
It’s free and only takes a minute

Register

Sign in

  • Similar Topics
    Replies
    Views
    Last post

Return to “R/C Off-Topic / Chit-Chat”

Who is online

Users browsing this forum: No registered users and 0 guests