Coming back with a vengence! A&L trailing arm content!
Coming back with a vengence! A&L trailing arm content!
Well guys I took a hiatus from RC's and SOLD EVERYTHING but my tools/charger - well now I'm back LOL..
Bought a used RERE World's that needs a refresh - and splurged on a re-released A&L C2 trailing arm chassis kit for it! (miss my first trailing arm RC10 that I never got to run) - this one will be run I promise!
Already bought the chassis kit from Jeff, and had him drill it for a stealth trans, and B5M wing mounts before shipping it out! I have the setup pretty well planned out - only things I'm stuck on is wheels/tires, and electronics (minus radio will be FlySky 2.4) .
Stuck on the wheels/tires and electronics -
JC retro setup (bought cause it's all discontinued)
AE 2.2 with modern tires (waiting to buy)
vintage or modern electronics -
brushless setup with a 13.5t or so setup
Novak or Tekin race ESC with a 12t-15t mod
2s lipo and a Flysky 2.4 is only for sure electronics
MAN are parts getting harder to find!
Got coming -
A&L black chassis/trailing arm kit - drilled for stealth trans/B5 wing mounts
AE Viper body
AE 75t spur
AE B3 wing buttons (since I can't find Trinity blue buttons)
AE RC10 GT aluminum front tube mounts
B44.2 9911 cvd bones (have 1 new one so had to buy 1 nip)
Lots of AE hardware (blue aluminum)
DTX aluminum 19mm servo arm (blue)
DTX 3/16" x 5/16" front wheel bearings
DTX 3/16" x 3/8" rear axle bearings (for cvd's!)
JC Hazard 1.9/1.7 black wheels
JC Double Dee's 1.7's
JC Rips 1.9's
JC B5 Stabilizer wings (2 wings - one for B5 mount and 1 for wire mount)
Lunsford turnbuckles (World's kit is $2 cheaper than buying them in pairs for the front)
RPM rod ends (blue)
Trinity style repop aluminum steering rack
Sorry no actual pics yet! Going to wait til it all gets here and post pics as I go..
Teaser of the basic look I'm going for!
Bought a used RERE World's that needs a refresh - and splurged on a re-released A&L C2 trailing arm chassis kit for it! (miss my first trailing arm RC10 that I never got to run) - this one will be run I promise!
Already bought the chassis kit from Jeff, and had him drill it for a stealth trans, and B5M wing mounts before shipping it out! I have the setup pretty well planned out - only things I'm stuck on is wheels/tires, and electronics (minus radio will be FlySky 2.4) .
Stuck on the wheels/tires and electronics -
JC retro setup (bought cause it's all discontinued)
AE 2.2 with modern tires (waiting to buy)
vintage or modern electronics -
brushless setup with a 13.5t or so setup
Novak or Tekin race ESC with a 12t-15t mod
2s lipo and a Flysky 2.4 is only for sure electronics
MAN are parts getting harder to find!
Got coming -
A&L black chassis/trailing arm kit - drilled for stealth trans/B5 wing mounts
AE Viper body
AE 75t spur
AE B3 wing buttons (since I can't find Trinity blue buttons)
AE RC10 GT aluminum front tube mounts
B44.2 9911 cvd bones (have 1 new one so had to buy 1 nip)
Lots of AE hardware (blue aluminum)
DTX aluminum 19mm servo arm (blue)
DTX 3/16" x 5/16" front wheel bearings
DTX 3/16" x 3/8" rear axle bearings (for cvd's!)
JC Hazard 1.9/1.7 black wheels
JC Double Dee's 1.7's
JC Rips 1.9's
JC B5 Stabilizer wings (2 wings - one for B5 mount and 1 for wire mount)
Lunsford turnbuckles (World's kit is $2 cheaper than buying them in pairs for the front)
RPM rod ends (blue)
Trinity style repop aluminum steering rack
Sorry no actual pics yet! Going to wait til it all gets here and post pics as I go..
Teaser of the basic look I'm going for!
- GoMachV
- Approved Member
- Posts: 11196
- Joined: Sun Apr 29, 2012 10:31 pm
- Location: Twin Falls, ID
- Has thanked: 765 times
- Been thanked: 2207 times
Re: Coming back with a vengence! A&L trailing arm content!
Are you sure duratrax makes a 3/16 x 3/8 flanged bearing?
I searched eBay and the ones I found were from rcboys
https://www.ebay.com/itm/372020028795
I searched eBay and the ones I found were from rcboys
https://www.ebay.com/itm/372020028795
It's time to stand up to the bully. Support the companies that support the industry, not the ones that tear it down. Say no to Traxxas
Factory Works website
Factory Works website
Re: Coming back with a vengence! A&L trailing arm content!
That's who I got them from! Ha I just assumed they were Duratrax my bad if they aren't, need them either way
- GoMachV
- Approved Member
- Posts: 11196
- Joined: Sun Apr 29, 2012 10:31 pm
- Location: Twin Falls, ID
- Has thanked: 765 times
- Been thanked: 2207 times
Re: Coming back with a vengence! A&L trailing arm content!
Ok cool. That's a pretty odd bearing so I wanted to make sure.
It's time to stand up to the bully. Support the companies that support the industry, not the ones that tear it down. Say no to Traxxas
Factory Works website
Factory Works website
- NomadRacer
- Approved Member
- Posts: 1467
- Joined: Sun Apr 16, 2017 7:29 am
- Location: Eastern Shore of Virginia
- Has thanked: 83 times
- Been thanked: 77 times
Re: Coming back with a vengence! A&L trailing arm content!
I got my 3/16 x 3/8" flanged bearings from AVID.
Bum on Direct Deposit
Re: Coming back with a vengence! A&L trailing arm content!
Well priced a Turnigy 75amp Trackstar turbo ESC, 13.5t stock spec motor, program card, and Turnigy brushless servo at $133 shipped
A vintage ESC/motor, and servo will be about the same I imagine..
A vintage ESC/motor, and servo will be about the same I imagine..
Create an account or sign in to join the discussion
You need to be a member in order to post a reply
Create an account
Not a member? register to join our community
Members can start their own topics & subscribe to topics
It’s free and only takes a minute
Sign in
-
- Similar Topics
- Replies
- Views
- Last post
-
- 1 Replies
- 947 Views
-
Last post by a01butal
-
- 11 Replies
- 1966 Views
-
Last post by GeekSpeed
-
- 12 Replies
- 2975 Views
-
Last post by duckhead
-
- 8 Replies
- 416 Views
-
Last post by 1911Colt
-
- 5 Replies
- 589 Views
-
Last post by juicedcoupe
-
- 5 Replies
- 916 Views
-
Last post by metallicats33
-
- 33 Replies
- 1667 Views
-
Last post by joe sumasky
-
- 2 Replies
- 461 Views
-
Last post by cyberded
Who is online
Users browsing this forum: 80sRunner, Google Adsense [Bot], Thorvald and 10 guests