Re: Gomachv's 4wd RC10 project, still unnamed and unproven
Posted: Fri Feb 14, 2014 4:39 pm
Should I add teeth? 
donRC10Talk - The Net's Largest Vintage R/C Community
Gomachv's 4wd RC10 project- finished!
Page 10 of 14
Re: Gomachv's 4wd RC10 project, still unnamed and unproven
Posted: Fri Feb 14, 2014 6:31 pm
Just add two bugsbunny teeth at top the hole!! don
donRe: Gomachv's 4wd RC10 project, still unnamed and unproven
Posted: Fri Feb 14, 2014 6:36 pm
Don't you mean a grill?gomachv wrote:Should I add teeth?
Re: Gomachv's 4wd RC10 project, still unnamed and unproven
Posted: Fri Feb 14, 2014 6:39 pm
I don't think I could fit his head under the pin router to try it!
Re: Gomachv's 4wd RC10 project, still unnamed and unproven
Posted: Fri Feb 14, 2014 9:32 pm
please try.
Re: Gomachv's 4wd RC10 project, still unnamed and unproven
Posted: Fri Feb 14, 2014 10:18 pm
a red tongue would be easy 
Re: Gomachv's 4wd RC10 project, still unnamed and unproven
Posted: Fri Feb 14, 2014 10:20 pm
vintage AE wrote:a red tongue would be easy
If I did, we could finally name this pig!
Miley!
Lol
Re: Gomachv's 4wd RC10 project, still unnamed and unproven
Posted: Fri Feb 14, 2014 11:15 pm
only if we could see her twerk
Good call though!
Good call though!
Re: Gomachv's 4wd RC10 project, still unnamed and unproven
Posted: Fri Feb 14, 2014 11:37 pm
Perhaps??
BTW, if you search for images of sex dolls prepare to be creeped out...
BTW, if you search for images of sex dolls prepare to be creeped out...
Re: Gomachv's 4wd RC10 project, still unnamed and unproven
Posted: Fri Feb 14, 2014 11:57 pm
Re: Gomachv's 4wd RC10 project, still unnamed and unproven
Posted: Sat Feb 15, 2014 12:21 am
For whatever reason that doll was named "Virginia Thomas" by the manufacturer. You could name the car "Virginia" and paint the body WWII fighter plane style.
Re: Gomachv's 4wd RC10 project- IT RUNS (but still unnamed)
Posted: Mon Feb 17, 2014 7:49 pm
It runs
Ne belt tensioner, I have only heard it skip a couple times but I'm only running a midnight stock motor and 6 cell pack, all old school. Feels ok, needs a lot of suspension work (not my strong point) but as a proof of concept.....it works!
Note: I swapped out the rear hubs and tires as the 2.2 were so tall it was under driving the front end. This is fairly square now.
This will most likely end up on eBay very soon. I have ideas to implement on a newer and more purple chassis
[youtube]Aypz4LFsswM[/youtube]
Ne belt tensioner, I have only heard it skip a couple times but I'm only running a midnight stock motor and 6 cell pack, all old school. Feels ok, needs a lot of suspension work (not my strong point) but as a proof of concept.....it works!
Note: I swapped out the rear hubs and tires as the 2.2 were so tall it was under driving the front end. This is fairly square now.
This will most likely end up on eBay very soon. I have ideas to implement on a newer and more purple chassis
[youtube]Aypz4LFsswM[/youtube]
Re: Gomachv's 4wd RC10 project- IT RUNS (but still unnamed)
Posted: Mon Feb 17, 2014 8:21 pm
Sweet!! What are your plans/thoughts for the tensioner?
Re: Gomachv's 4wd RC10 project- IT RUNS (but still unnamed)
Posted: Mon Feb 17, 2014 8:24 pm
The belt needs to tension the top, and that creates a problem unless it's minimal. I'm going to play with it a bit first- but this is one thing I hope to overcome with a couple little tweaks on the next one
Re: Gomachv's 4wd RC10 project, still unnamed and unproven
Posted: Mon Feb 17, 2014 8:28 pm
If you can make this happen, I'm down and others for suregomachv wrote: It's still a ways off....but don't worry I'm sure I will be able to sell a few before long