Re: Project RC10 - LCG
Posted: Thu May 26, 2016 4:58 am
The servo is a Savox 1251 low profile
RC10Talk - The Net's Largest Vintage R/C Community
Project RC10 - LCG
Page 2 of 3
Re: Project RC10 - LCG
Posted: Thu May 26, 2016 6:55 pm
Cool, thanks for the info. Just scored a graphite RC10 and that would work great with it.
Re: Project RC10 - LCG
Posted: Sat Jun 04, 2016 2:58 pm
Gearbox is in!
Re: Project RC10 - LCG
Posted: Sat Jun 04, 2016 3:01 pm
Rear tower and shocks mounted up, Test fitted the motor and lipo, not far away now!
Re: Project RC10 - LCG
Posted: Fri Jun 24, 2016 2:07 pm
Waterfall brace is in and shorty installed using Yokomo bmax 3 cradle and B44 posts
Re: Project RC10 - LCG
Posted: Fri Jun 24, 2016 2:42 pm
Re: Project RC10 - LCG
Posted: Fri Jun 24, 2016 6:31 pm
Esc is in and tapped out the b44 battery posts to m3 and put on the B5 thumb screws
Re: Project RC10 - LCG
Posted: Sun Jun 26, 2016 3:08 am
Really nice build
Re: Project RC10 - LCG
Posted: Wed Jul 27, 2016 4:08 pm
Thanks for the nice comments guys 
Well its ready to hit the track!! I will take my go pro and get some footage and post it up shortly
Well its ready to hit the track!! I will take my go pro and get some footage and post it up shortly
Re: Project RC10 - LCG
Posted: Wed Jul 27, 2016 4:22 pm
Need to make a fake VW engine to take up the space at the back.
Re: Project RC10 - LCG
Posted: Wed Jul 27, 2016 6:50 pm
http://www.shapeways.com/product/FU7LEU9CD/1-10scale-vw-engine?optionId=40503743yellowdatsun wrote:Need to make a fake VW engine to take up the space at the back.
http://www.shapeways.com/product/F4H3LTFGD/ff10001-flat-4-engine-part-1-of-2?optionId=57894701&li=user-profile
Re: Project RC10 - LCG
Posted: Thu Jul 28, 2016 4:37 am
Yes agree I needs something to fill the gap at the back of the chassis!
Track test today!!
Track test today!!
Re: Project RC10 - LCG
Posted: Thu Jul 28, 2016 4:41 am
Guys need some help, with the yz2 box in the car using b44 drive shafts they are 2-3mm too long causing the driveshaft to hit the inner part of the outdrive and not giving me full suspension travel
Any ideas on how I can overcome this issue?? Is there any arms that are a little longer than the stock worlds arms??
Is there a different drive shaft that's shorter than the 44 one??
Any ideas on how I can overcome this issue?? Is there any arms that are a little longer than the stock worlds arms??
Is there a different drive shaft that's shorter than the 44 one??
Re: Project RC10 - LCG
Posted: Thu Jul 28, 2016 8:52 am
are they the b44 front driveshafts?
it looks like you are using b4 rear hubs and stock arms and mounts, is that correct? Look into Niki's shapeways store for his quadra arms and also some different arm mounts. I think he's got something that might work. You might end up with the quadra arms and stock hub carriers or some kinda combination like that.
it looks like you are using b4 rear hubs and stock arms and mounts, is that correct? Look into Niki's shapeways store for his quadra arms and also some different arm mounts. I think he's got something that might work. You might end up with the quadra arms and stock hub carriers or some kinda combination like that.
Re: Project RC10 - LCG
Posted: Thu Jul 28, 2016 12:04 pm
How long are the dogbones you are using now? In mm.