Re: Losi JRX Pro SE build
Posted: Wed Feb 19, 2025 9:25 pm
It fit like a glove. I was sort of wondering myself.
One last shot of a factory fresh chassis, before it gets bolted up.
RC10Talk - The Net's Largest Vintage R/C Community
Losi JRX Pro SE build
Page 2 of 4
Re: Losi JRX Pro SE build
Posted: Wed Feb 19, 2025 11:43 pm
Re: Losi JRX Pro SE build
Posted: Thu Feb 20, 2025 7:42 pm
nice with the titanium shafts and aluminum studs, I was gonna mention them steering cranks came with standard bearings back in the day but fit the flange bearings nicely.
Re: Losi JRX Pro SE build
Posted: Sat Feb 22, 2025 2:02 am
I'm using these rare RPM shock standoff. I've never mounted a set before. I love the small detail of the RPM lettering on them. The Jammin tower is attached to a RPM bulkhead. Aluminum 4-40 and 8-32 hardware used throughout.
Re: Losi JRX Pro SE build
Posted: Sun Feb 23, 2025 3:33 am
Rear end assembled and installed onto the chassis. Using Lunsford retro turnbuckles and RPM ends. I was planning to use these cool vintage grey units, but remembered they are for a larger diameter HD thread. RPM rear carrier and chassis brace finish off the slider.
Re: Losi JRX Pro SE build
Posted: Sun Feb 23, 2025 1:34 pm
Your PRo SE car build is looking fantastic.
Re: Losi JRX Pro SE build
Posted: Sun Feb 23, 2025 3:52 pm
Those RPM 0 toe rear mounts are a thing i didn't know existed and now i want them
Re: Losi JRX Pro SE build
Posted: Sun Feb 23, 2025 4:00 pm
Re: Losi JRX Pro SE build
Posted: Mon Feb 24, 2025 2:20 pm
Not even a scratch from the screwdriver on the screw heads!
Just wow!
Just wow!
Re: Losi JRX Pro SE build
Posted: Mon Feb 24, 2025 2:26 pm
I'd like to ask how the screw heads all get aligned like that, but I don't want to know the real answer. It's kind of like 'you should never meet your heroes'. I'll just go with having the superhuman ability to always start screws of identical length at the same clocking, and knowing how to adjust the starting position based upon minor variations in screw length. That's 100% the real method.
Re: Losi JRX Pro SE build
Posted: Wed Feb 26, 2025 11:25 am
Well, I guess we won't give you the right answer but we do the same black magic with electrical wall plates to align the screws with each other.Frankentruck wrote: ↑Mon Feb 24, 2025 2:26 pm I'd like to ask how the screw heads all get aligned like that, but I don't want to know the real answer. It's kind of like 'you should never meet your heroes'. I'll just go with having the superhuman ability to always start screws of identical length at the same clocking, and knowing how to adjust the starting position based upon minor variations in screw length. That's 100% the real method.
Re: Losi JRX Pro SE build
Posted: Wed Feb 26, 2025 3:46 pm
I have to say it's harder to avoid scratching the screw heads than it is to get them aligned.
Yes RogueIV, I feel you on the electrical wall plates and making sure the screw heads are aligned. I actually replaced all the electrical covers in my house with fancy screw free units. Problem solved there!
Yes RogueIV, I feel you on the electrical wall plates and making sure the screw heads are aligned. I actually replaced all the electrical covers in my house with fancy screw free units. Problem solved there!
Re: Losi JRX Pro SE build
Posted: Tue Mar 04, 2025 9:41 pm
Shocks built using SRS cartridges and MIP internals. The internals are held in by a snap ring.
I'm not sure on shock spring color. I had sourced front and rear shock sprinks in black, for a cleaner look. However colored springs just seem to suite an SE.
I'm not sure on shock spring color. I had sourced front and rear shock sprinks in black, for a cleaner look. However colored springs just seem to suite an SE.
Re: Losi JRX Pro SE build
Posted: Tue Mar 04, 2025 11:28 pm
Wow so much better than what I had done to it. 
Re: Losi JRX Pro SE build
Posted: Tue Mar 04, 2025 11:40 pm