Page 5 of 6

Re: Ultima 2019

Posted: Mon Dec 16, 2019 7:44 pm
by GoMachV
You should not have a problem with any standard length and form factor Lipo pack installed in the normal spot. The chassis has plenty of clearance.

Shorty packs will not fit as the terminals can short on the chassis… unless…

Re: Ultima 2019

Posted: Mon Dec 16, 2019 8:19 pm
by mikem65d
Thank you for the quick reply.

The Optima and Tomahawk have less clearance than i anticipated.
3 -5,000 mah packs in hard case had me opening the cases and removing the inner foam protection and then trim the hard case to gain 3mm.

The Ultima i just ordered

Re: Ultima 2019

Posted: Thu Feb 20, 2020 9:19 pm
by Delorean
To run a shorty in the spot where the normal full stick pack sits, could you narrow up the top deck in the battery area and bring inwards the screw holes that the plastic brackets bolt to, thus moving the battery straps inwards? i haven't got my car yet so im only speculating from afar. Even if the battery was a little to one side so the terminals wouldn't short on the chassis, you could put it to the right to offset the motor a bit

Re: Ultima 2019

Posted: Thu Feb 20, 2020 9:22 pm
by Delorean
While i'm here guys, any other tips on the car? i'm picking it up to go vintage racing, i've heard they're a bit on the heavy side, so i was thinking titanium screws might help as it looks like theres a lot of screws holding it together and maybe some milling of the motor plate which looked fairly thick

Cheers

Re: Ultima 2019

Posted: Fri Feb 21, 2020 6:19 am
by DennisM
No need for that - the Ultima isn´t heavier than it´s competitors. You might even need to add weight to keep it legal.
Follow the shortest route on the track and don´t hit anything - You´ll finish 1st or 2nd :D
Proper tuning is tires, battery placement, steering, shock absorption, camber-caster-toe angles etc.

Good luck racing - I´m in it for the hotdogs and tire kicking :wink:

Re: Ultima 2019

Posted: Tue Feb 25, 2020 2:30 am
by Mr. ED
My solution for shorty batteries is in prototype stage (printing).
Once tested I'll put it on shapeways.
Here's an early design. The final one looks a lot different but I have no picture on hand.

Re: Ultima 2019

Posted: Tue Feb 25, 2020 6:02 pm
by Delorean
Mr. ED wrote: Tue Feb 25, 2020 2:30 am My solution for shorty batteries is in prototype stage (printing).
Once tested I'll put it on shapeways.
Here's an early design. The final one looks a lot different but I have no picture on hand.
Looks really cool, im looking forward to hearing more about it!

Re: Ultima 2019

Posted: Tue Feb 25, 2020 6:25 pm
by GoMachV
.

Re: Ultima 2019

Posted: Tue Mar 03, 2020 3:33 am
by Mr. ED
The first prototype print of the shorty holders came in yesterday.
I didn't have time to mount it yet, but you get the idea.
Top of pic is the frontside of the car. The hinge and retainer bolts go in from the bottom. That way you can unlock the retainer without that bolt falling out. Plus, it keeps the top nice and clean of bolt heads.
P_20200302_210903.jpg
And this is the full kit:

Re: Ultima 2019

Posted: Tue Mar 03, 2020 8:46 am
by Dadio
Phew that's a lot of work in that heap of parts ! Can't wait to see it assembled .

Re: Ultima 2019

Posted: Tue Mar 03, 2020 12:07 pm
by Mr. ED
Here it is as I ran it at the vintage euro masters this weekend:
P_20200223_213438.jpg
and here it is on the turbo ultima chassis with the printed cage body, but before the batteryholders arrived:
P_20200126_155419.jpg

Re: Ultima 2019

Posted: Sat May 30, 2020 2:58 am
by Michaels tc
Anyone sell a carbon top deck?

Re: Ultima 2019

Posted: Sun May 31, 2020 12:32 am
by Michaels tc
Does it make any difference to change the bushing and bearing in the steering to a flanged and rubber shielded bearing?

Re: Ultima 2019

Posted: Sun May 31, 2020 2:42 pm
by Biz73
After bidding on a few RC10's on Ebay I realized they are going for more than what I can pay and still be able to afford parts that need to be replaced. I bit the bullet and went with my original plan and placed my order for an Ultima from Tower. They have a $40 coupon right now that lasts until Tuesday.

Hopefully I will be able to get some RC money together after the Covid crisis so I can get an RC10 at a reasonable price. It's definitely high on my "I NEED it" list :D

Re: Ultima 2019

Posted: Fri Jun 05, 2020 8:11 pm
by Biz73
Does anyone know what size the wheels are? I'm trying to look at options for different tires.

I waited all day for my kit to be delivered and 10 minutes ago Fedex changed the delivery date to tomorrow :evil: Don't they know that my toy car is the most important package they have! :lol: