RC10Talk - The Net's Largest Vintage R/C Community

world graphite team car . i think i have seen one in here i just cant find it or was there such a kit .

new project for me i would like to base it off that (its my rc1009 back in black)


i will try to get some pic up .

i have a lot of questions .

thanks everyone for a great sight .

is there a worlds rpm front bulk head
will a b2 motor plate work on a b4 stelth trans and will a b4 bolt in .edit(are the holes all the same)

just to be clear, there is no "worlds graphite". it's just an '89 worlds looking chassis that was put in the last run of graphite team car kits.

http://www.rc10talk.com/viewtopic.php?f=35&t=6032

cool

i dont have the fine woven plates you guys have .

i will be using a new duratrax .

i will get some pic up as soon as i can

You aren't going to see a worlds looking chassis any time soon . mrlexan has them all .

yea i see that they made 10 and he has 5 of them .

this is just my first from scrach rc10

my fav is the graphite rc10 so i want to put a new one to go with my old one


it in no way to rep time value or any of that stuff just some fun with a rc10 build .
its going to be a runner (namely to wip up on brandon and mark)lol

does any one know of a hinge pin set or parts length (kinda want the dang old eclips)

sorry short on time will get better info later this week .

good luck at the vintage nats all . cant make it this year but maybe the next one .

jsrracing wrote: does any one know of a hinge pin set or parts length (kinda want the dang old eclips)

Kingpins: http://www3.towerhobbies.com/cgi-bin/wti0001p?&I=LX2526&P=7
Front outer hinge pins: http://www3.towerhobbies.com/cgi-bin/wti0001p?&I=LX2526&P=7
Rear inner hinge pins: http://www3.towerhobbies.com/cgi-bin/wti0001p?&I=LX2565&P=7
Rear outer hinge pins: http://www3.towerhobbies.com/cgi-bin/wti0001p?&I=LX2528&P=7

Tower lists the front inner hinge pins and discontinued. The arms are a little under 1-1/2" wide, better to go a little longer and take up the slack with shims.

thanks

i was looking but i was not sure .


parts i have so far
chassis duratrax
rpm worlds rear bulk head white(phhh when did they start making them out of gold)
rpm arms
mip bellcranks
front bulk heads
hinge pins on the way
graphite towers bat holder and trans brace on the way

kinda funny the graphite parts are easy unlike 20 years ago.

i have a set of blue alum screws and blue shocks (im not sure about doing the blue thing yet . Kinda seems right now

What chassis by Duratrax?

If you are using the RPM World's front end then you'll need to use the inner hinge pins from the RC10T: http://www3.towerhobbies.com/cgi-bin/wti0001p?&I=LX2916&P=7

the rear bulkhead is rpm

is there such a part for the front, would be real cool to have

its a rc10 duratrax replacement chasis i think that it is a nonwoven carbon that i went nuts over on fleabay should be here by end of week. o first nib part yea

i will post pic when the parts start comming in .

trying to do a non ae carbon rc10

think its going to be hard to do, on the rear arm carriers

i see your asking about an rpm worlds front bulkhead. which arms are you planning on using, the rpm team car arms? they won't work with that bulkhead. they're to short, and they won't mount to the bulkhead, either. and you'd also have to narrow the front of the chassis to even attach the bulkhead to it. you'd need to find one of the rpm 1 piece front bulkheads for the standard kickup. they only came in black.

rpm, andy's, hg, and gpm off the top of my head made rear arm mounts for the rc10. you just need to find them.

so on the front i have to use black 6207 . is this correct or
rpm 1 piece front bulkheads for the standard kickup. they only came in black.
its a start.



it may be my computer but everytime i google it . i just get this big fat guy laughing.

this is the rpm 1 piece bulkhead. i don't remember the part number off the top of my head. they pop up on ebay every now and then.
andy's had one that was very similar, too. i don't have a pic of one on my laptop, though.

jsrracing wrote:so on the front i have to use black 6207 . is this correct or
rpm 1 piece front bulkheads for the standard kickup. they only came in black.
its a start.



it may be my computer but everytime i google it . i just get this big fat guy laughing.

thats just the reflection on the screen, turn the light off and he'll go away.

lol

i want one, nice pic. you know im gona ask were and how do i get my hands on one(i will keep my fleadar up)

jsrracing wrote:so on the front i have to use black 6207 . is this correct or
rpm 1 piece front bulkheads for the standard kickup. they only came in black.
its a start.



it may be my computer but everytime i google it . i just get this big fat guy laughing.

That's just Henslo standing behind you James