RC10Talk - The Net's Largest Vintage R/C Community

Has anyone seen these come up on ebay



Yokomo Early YZ10 870C Works Front belt replace ZC651:
http://cgi.ebay.com/Yokomo-Early-YZ10-870C-Works-Front-belt-replace-ZC651-/270772313312

Yokomo Later YZ10 94 Pavidis Front belt replace ZD652:
http://cgi.ebay.com/Yokomo-Later-YZ10-94-Pavidis-Front-belt-replace-ZD652-/270772314102


Yokomo YZ10 Rear belt replace ZC656 Pavidis Works 870C:
http://cgi.ebay.com/Yokomo-YZ10-Rear-belt-replace-ZC656-Pavidis-Works-870C-/270772312068


I think I'll be ordering a couple of 652 and 656 next week to check out the quality

I was just looking at those-too bad there is no 2mm

Q.

can you tell me if you sell or plan to sell 2mm pitch belts for the Yokomo YZ10? thanks

A.

sorry we have no 2mm pitch
regards

i've picked up a couple of belts in 3mm HTD to try and split in two, from SDP-SI. I'll have to post the results I get.

SDP-SI also sells GT2 2mm belts, which from what I can tell on the internet, are interchangeable with HTD, ie, an HTD pulley will work with either. I also noticed that they have 3mm wide belts. You can probably pick up a drop-on replacement right from them for the 2mm pitch system. it's worth taking a look, the company is located in NY, I paid less than 5 bucks for shipping, and a 504mm long 2mm pitch 3mm wide GT2 belt is around 4 bucks. Not sure exactly how long of a belt you need, they have almost every tooth count.

I got my belts in yesterday. The belts look great, I now have to devise a jig to slice them in half. I was also wrong on shipping. it turns out there was a 4 dollar charge for handling and the damn shipping was 12 bucks. So half the order was shipping, and half was the price of the belts. So I'm a little miffed about that, but if I can successfully slice the belts in two, I will have picked up 2 sets of belts for around 28 bucks. Not bad. Also, I picked 9mm belts, so when I'm done, I should have 4.5mm belts, slightly wider than a stock belt, which should be stronger.

When it comes to SDP, the shipping price at checkout is NEVER the shipping/handling they charge. I think their S&H policies suck, but they're the only ones who have hard-to-find small moving parts like belts, chains, gears, etc. So, we're stuck...

yeah, it appears so. I have mentally bookmarked this so I'll be sure to make my order totals such that the parts are worth more than the shipping in the future. this was my first order with them. Easy internet ordering, just sucky S+H policy as you said.

I know the seller from 90's. he didn't sell pavidis front belt before. and I believe he have read my yokomo belt thread on korean rc forum.
btw, I found a shop has 2mm belts and already asked to find 262T a couple of weeks ago

59burst wrote:I found a shop has 2mm belts and already asked to find 262T a couple of weeks ago

Yeah!!!!!!!

they found 260T and 264T 2mm pitch belts. but not 262T yet

1. i think i have the 262 2mm pitch belt shall look

2. www.beltcorp.com they have a supirior collection of lenght and pitch compared to sdp.

mvh isobarik

isobarik wrote: http://www.beltcorp.com

found it
http://beltcorp.thomasnet.com/item/ing-belts-neoprene-timing-belts-metric-pitch-belts/2mr-power-grip-174-gt-174-2-neoprene/2mr-524?
thanks isobarik

59burst wrote:

isobarik wrote: http://www.beltcorp.com

found it
http://beltcorp.thomasnet.com/item/ing-belts-neoprene-timing-belts-metric-pitch-belts/2mr-power-grip-174-gt-174-2-neoprene/2mr-524?
thanks isobarik

good work hyeong, one more part to the puzzle

anyone else in australia want a 262 tooth? i can order a few.

I/ve used him before and his prices are really good.

As for the belts im still not sure as my belts are slipping on my Lazer Zx but not sure if it's the belts, or pulleys..

if anyone can work it out it will be you mark