Page 1 of 2
What outdrives fit a RPM 2.65 ?
Posted: Mon Jul 30, 2012 1:47 pm
by OGRC10T
I am rebuilding the trans on my rc10t...the bushings wiped all the shafts out...i decided to upgrade to the rpm 2.65 and avid bearings. I am trying to locate the stock 6577 and 6578 outdrives for the diff but I find that very little are available and the product is discontinued....my question is that I am wondering since the stealth trans came in multiple models is there different outdrives that will work for me or possibly a newer entire diff setup to swap in the rpm 2.65
I appericate any help or advice I can get
Re: What outdrives fit a RPM 2.65 ?
Posted: Mon Jul 30, 2012 2:28 pm
by Charlie don't surf
Stock 2.25 outdrives and diff only. Try Customworks RC or Dynotech racing, they both had Customworks 2.25 (stealth copies) left and rights last time I looked.
Re: What outdrives fit a RPM 2.65 ?
Posted: Mon Jul 30, 2012 4:05 pm
by Quikenuff
Does anyone know if this an original stealth compatable kit?
http://www.teamassociated.com/parts/details/7678/
Tower still carries this kit I think, when I was searching for out drives I found this, but never ordered them because I wasn't sure.
Quik
Re: What outdrives fit a RPM 2.65 ?
Posted: Mon Jul 30, 2012 4:18 pm
by jwscab
describes the application in the description, which unfortunately, does not include the original stealth ratio of 2.25. the diff gear, diff rings, outdrives are all too large.
Re: What outdrives fit a RPM 2.65 ?
Posted: Mon Jul 30, 2012 4:38 pm
by OGRC10T
Charlie don't surf wrote:Stock 2.25 outdrives and diff only. Try Customworks RCor Dynotech racing, they both had Customworks 2.25 (stealth copies) left and rights last time I looked.
Thanks for the info, I checked both sites but didn't see any...at least I know the stock 6577 and 6578 outdrives are the only ones I can get
Re: What outdrives fit a RPM 2.65 ?
Posted: Mon Jul 30, 2012 4:46 pm
by Quikenuff
jwscab wrote:describes the application in the description, which unfortunately, does not include the original stealth ratio of 2.25. the diff gear, diff rings, outdrives are all too large.
Thanks for explaining, Now I see. The bearings for the hubs may be the same but diff rings are larger.
Re: What outdrives fit a RPM 2.65 ?
Posted: Mon Jul 30, 2012 6:04 pm
by Charlie don't surf
OGRC10T wrote:Charlie don't surf wrote:Stock 2.25 outdrives and diff only. Try Customworks RCor Dynotech racing, they both had Customworks 2.25 (stealth copies) left and rights last time I looked.
Thanks for the info, I checked both sites but didn't see any...at least I know the stock 6577 and 6578 outdrives are the only ones I can get
I'll get you the pages I found them in-
Re: What outdrives fit a RPM 2.65 ?
Posted: Thu Aug 02, 2012 10:56 am
by OGRC10T
Hey Charlie any luck in finding where you found those outdrives ? I missed out on a set on ebay and still searching, I got all my 2.65 case and avid bearings all ready to go just cant seem to find these dumb outdrives, i definitly dont wanna put my olds ones back in because the bushing worn into the metal alot
Re: What outdrives fit a RPM 2.65 ?
Posted: Sat Aug 04, 2012 3:04 pm
by OGRC10T
Re: What outdrives fit a RPM 2.65 ?
Posted: Sat Aug 04, 2012 9:34 pm
by RC104ever
Omg if those fit I'm ordering some right now.
Re: What outdrives fit a RPM 2.65 ?
Posted: Sun Aug 05, 2012 1:01 am
by OGRC10T
RC104ever wrote:Omg if those fit I'm ordering some right now.
Gonna call them tomorrow to see what they are for.
If not i am done looking...i am gonna use a mircometer and measure how much wear i actually got...anybody got a measurement for reference ?
Worst case they are going back in ...the wobble cant be that bad what will i lose 2 dollars in bearings ?
gotta drive the truck already
Re: What outdrives fit a RPM 2.65 ?
Posted: Fri Aug 10, 2012 5:29 pm
by rctenracer
The rpm 2.65 comes with a top shaft and case. Use the stealth doner to complete. And yes the custom works are a dirrect fit. 4364 and 4365 are the correct ones. They are around 12 to 13 bucks each from tower.
Re: What outdrives fit a RPM 2.65 ?
Posted: Sat Aug 11, 2012 6:12 am
by bully
I thought they are for the 2.40 diff assembly when i was looking around everywhere for weeks, i was lucky to buy up some from dynotech b4 he sold out.
Re: What outdrives fit a RPM 2.65 ?
Posted: Fri Aug 17, 2012 9:37 pm
by bully
rctenracer wrote:
The rpm 2.65 comes with a top shaft and case. Use the stealth doner to complete. And yes the custom works are a dirrect fit. 4364 and 4365 are the correct ones. They are around 12 to 13 bucks each from tower.
Anyone else confirm that these custom works outdrives are for the 2.25 stealth
Re: What outdrives fit a RPM 2.65 ?
Posted: Sat Aug 18, 2012 4:22 am
by rctenracer
rctenracer wrote:
The rpm 2.65 comes with a top shaft and case. Use the stealth doner to complete. And yes the custom works are a dirrect fit. 4364 and 4365 are the correct ones. They are around 12 to 13 bucks each from tower.
Upate . The 4364 and 4365 custome works outdrives are the same size but will not accept the stealth 2.25 diff rings. They won't work.