Page 1 of 2

A-Main RC10gt conversion

Posted: Wed May 29, 2013 12:10 am
by GoMachV
Picked this up a while back thinking it would make a good project. The chassis was near perfect so I didn't do anything besides strip and anno it gold. The parts were painted black, i stripped them and dyed them properly. Very happy with the color combo, just need a couple little bits to wrap this one up.

Image

Image

Image

Image

Image

Re: Dudgeon Gt

Posted: Wed May 29, 2013 1:06 am
by justinspeed79
Very nice! 8) :D

Re: Dudgeon Gt

Posted: Wed May 29, 2013 4:31 pm
by LTO_Dave
Very nice! I like the gold axles that bring it all together. :wink:

Re: Dudgeon Gt

Posted: Wed May 29, 2013 5:42 pm
by SFC K
That looks really nice! I too like the gold and black color combo. 8)

Re: Dudgeon Gt

Posted: Wed May 29, 2013 7:24 pm
by DHood
Love it! To bad it's not a Dudgeon, It's a later A-Main conversion.

Re: Dudgeon Gt

Posted: Wed May 29, 2013 8:23 pm
by GoMachV
Still designed by Kunio, sold under the A-Main name, same as his earlier electric conversions. Tomato tomato

Re: A-Main RC10gt conversion

Posted: Thu May 30, 2013 6:47 am
by marlo
Looks good Jeff, is there any special anno procedure on parts that get heat, such as pipe, and head, or the temp's aren't high enough to do damage.

Re: A-Main RC10gt conversion

Posted: Thu May 30, 2013 9:05 am
by GoMachV
That's a good question! I have seen the old MIP heads start out purple and fade in color over time. Hmmm

Re: A-Main RC10gt conversion

Posted: Thu May 30, 2013 9:21 am
by GreenHell
The truck turned out really nice!

I have a purple MIP stinger pipe on my GT. So far only the manifold faded in color but the pipe looks fine and that’s after running several gallons of fuel. My guess is the much lighter gold anodizing should hold up reasonably well.

Re: A-Main RC10gt conversion

Posted: Thu May 30, 2013 9:34 am
by GoMachV
In all fairness too the MIP heads that I have seen faded were ran hard and put away...with nitro in em. I saw a video on removing anno color before and they did it with a small torch :shock: oh look....here is the link :mrgreen:

[youtube]CBmmXA1GDwo[/youtube]

Re: A-Main RC10gt conversion

Posted: Fri May 31, 2013 11:05 pm
by mikea96
That is cool i am going to try that!

Re: A-Main RC10gt conversion

Posted: Sun Jun 02, 2013 5:52 pm
by GoMachV
Well, this is as far as I'm going with her. I finally cleaned up the tires and bolted em on, new air filter and off she goes. A good friend of mine just offered to buy her. This was a fun build. It's nice when the parts aren't a challenge to find

Image

Image

Oh and I made a Kydex bumper. :mrgreen:
Image

Re: A-Main RC10gt conversion

Posted: Sun Jun 02, 2013 6:46 pm
by romulus22
Looks good. At a glance I would think Kyosho though by the color. Has that odd gold to it

Re: A-Main RC10gt conversion

Posted: Sun Jun 02, 2013 9:41 pm
by teman
Wow, that's niiice 8) I vote for some T3 gold shocks on that baby .oOO :mrgreen: Like these, just with gold shock caps :wink:
PC200451.JPG
PC200451.JPG (44.2 KiB) Viewed 2100 times
PC200451.JPG
PC200451.JPG (44.2 KiB) Viewed 2100 times
PC200452.JPG
PC200452.JPG (45.03 KiB) Viewed 2100 times
PC200452.JPG
PC200452.JPG (45.03 KiB) Viewed 2100 times

Re: A-Main RC10gt conversion

Posted: Sun Jun 02, 2013 9:45 pm
by GoMachV
I had some caps done in the same gold, but I didn't like it. With bodies too it would have looked great