If you would like to enter the contest, create a post as a "place holder". DO NOT POST ANY PICS. You have until the 5th of the month to lock in a spot (10 entries max). You will then have 2 days to edit your post and attach the pics of your entry. The poll will be started on the night of the 7th. If you have not submitted your pics by then you will be removed from the contest.
Re: ** Build of the Month Contest - May 2025 ** - Winner - morrisey0
Posted: Fri May 02, 2025 9:53 am
by morrisey0
Bolink Invader O/R, with original Bolink Dirt Tracker Corvette body. Greenwood Corvettes "Spirit Of xxxx" tribute scheme.
Re: ** Build of the Month Contest - May 2025 ** - Winner - morrisey0
Posted: Sat May 03, 2025 7:18 am
by Charlie don't surf
My late 1995 B2 all-carbon build from Sept 2011, pics aren't on the thread any longer. All carbon parts, Yokomo shiny universals, team hoomies milled motor plate, hydradrive, gold MIP shafts, yokomo springs, ex team front tower, RCPS tie rods, Proline tires. LRP ICs with Team Associated import logo, Reedy Ultra Sonic 12x3, a LRP 1700 SCRCs, Airtronics servo and rec.
Re: ** Build of the Month Contest - May 2025 ** - Winner - morrisey0
Posted: Sun May 04, 2025 12:59 pm
by Janus
Here is my new RC10 Team Car (Re-Re) runner.
My previous runner had worn through it's 2nd chassis and every nut and bolt had to be checked after each run. So with the current "re-re rain" by AE, it was a perfect time for a fresh one.
I know, the current "cool thing" to do a long-arm, bigbored, GT transmission equipped monster.
But I wanted to keep a bit more simple (boring, I know.....) and just put in a JC-racing transmission to get a geardiff option for the car.
Other things are a stainless steel spine to give it some stiffness, altered front kick-up, a slipper weight (recent addition), etc....
Carryovers from the previous runner (the Mutant) include carbon shocktowers, ballbearing steering, and a few other bits and bobs.
Used a some FanRC parts as well, pretty happy with the material of the hubs and casterblocks. Not sure yet about the drive shafts and slipperplates. But time will tell.
Until everything is proven, it will have to do with a 7.5 brushless Novak motor. Other electrics include a Novak brushless esc, unknown servo and a Ko receiver controlled by a KO Esprit stick transmitter.
Ohh.. Since it's a runner I thought to put in a small video instead of a 2nd picture
Re: ** Build of the Month Contest - May 2025 ** - Winner - morrisey0
Posted: Mon May 05, 2025 3:37 pm
by TravelinTravis
Like most all of us, I used to race in a galaxy, and a life, far far away now. But after 2 years of collecting/building and thanks to many people on rc10talk, 36 years after last being on the track (last race 1989 On-Road Oval Nat's)...This is my Composite Craft Predator Lynx....at the track and FINALLY running, and turning some not too shabby hot laps, again:
Futaba S-132H Servo
Novak NER-2X (75MHz AM) Receiver
Novak 410-HPc Speed Controller
Magnum Sr. (FP-T3PG)(75MHz AM) Transmitter
NC-2500mAh SCR NiCd saddle packs
Revtech 16 turn double motor
Deans 4-Pin connectors
Rear shocks w/70WT TLR Silicone Shock Oil and standard Delta springs (Medium)
Front Springs @ .022
TOJ SabulaTech Body
32 Shore Hot Race Tires all around
Corally 33 Tire Juice (I think you can see it in the body off photos before I wiped'em down)
Build thread here: https://www.rc10talk.com/viewtopic.php?t=47650
