Search found more than 1002 matches
- Mon Feb 12, 2007 1:23 am
- Jump to forum
- Jump to topic
I have commercially reanodized quite a few RC10 chassis (as most here already know)... here's a few points to keep in mind: (1) Anodizing does not cover up any scratches. In fact, you will find scratches you never knew existed after you anodize. Hence, you will want your chassis absolutely smooth fo...
- Tue May 20, 2008 10:19 pm
- Jump to forum
- Jump to topic
Re: Rarest of the RARE
alright i was just wondering if there was some Unicorn out there that is the one thing no one can find I don't think there really is one thing. I'm sure everyone has their own one thing that they can't find. Like in my case, I can't seem to find the e-clip I dropped on the floor last week. :lol:
- Wed Jan 07, 2009 4:08 pm
- Jump to forum
- Jump to topic
- Thu Mar 05, 2009 10:06 pm
- Jump to forum
- Jump to topic
Re: RPM Worlds Car Instructions
click for larger image.........
- Fri Aug 21, 2009 9:51 am
- Jump to forum
- Jump to topic
Re: RC10T Specs?
I thought it would be convenient to have the SC10 specs in the same place: SC10 Length: 21.6" (550mm) Width: 11.5" (293mm) Track: 9.6" (245mm) Weight: 4.6lbs (2080g) Wheelbase: 12.9" (327mm) Internal Gear ratio: 2.6:1 RC10T Overall length 16.25" (413mm) Width 12.625" (3...
- Sat Mar 06, 2010 5:51 pm
- Jump to forum
- Jump to topic
Re: Bearing sizes for a 6 gear RC10?
1/4 x 3/8 flangedveghead211 wrote:Does anyone know what size bearings to use on Houge bellcrank steering?
- Sat May 01, 2010 5:16 pm
- Jump to forum
- Jump to topic
Re: T2's rear bulkhead
Hey David,holes line up fine,since no batt box I just run sideways. Johnny
- Mon Jul 05, 2010 9:43 pm
- Jump to forum
- Jump to topic
Re: Graphite chassis repair?
depending on how meticulous you are, you can repair this somewhat close to invisible, but you will need a donor part that has unidirectional fibers, file/drill/sand the slots nice and uniform, and cut out 'slugs' that fit with a small amount of air gap in them. take some crystal clear epoxy resin an...
- Thu Aug 05, 2010 9:57 pm
- Jump to forum
- Jump to topic
Re: Interchangeability of RC10 parts (Goldpan/ds/B2/B3/B4/GT
This whole post got me thinking... Why not have a post with all of the interchangeable parts that Associated makes? It might be good to make it a sticky so that people can find out what works and what doesn't work.
- Tue Sep 21, 2010 6:06 pm
- Jump to forum
- Jump to topic
Transmission Internal Drive Ratios
Lots of people are running their vintage cars more and more, and using contemporary electronics in them on the track. Gearing is always an issue for many newbies and vets, alike. To get a proper gear ratio for your motor, battery, tire and chassis, it's important to know the final drive ratio of the...
- Sat Oct 09, 2010 3:30 pm
- Jump to forum
- Jump to topic
Re: Very Early Prototype Associated Cars from Curtis
Hi, This is Curtis Husting. I'm not so sure you really want to attempt to make one of these chassis. It will be much harder than you think. If you think you want to attempt it, this is kind of how I did it. First I made a one inch thick aluminum plug that the aluminum would be formed around. Basical...
- Fri Mar 09, 2012 8:53 pm
- Jump to forum
- Jump to topic
"The Poor Man's" RPM Steering Enhancement Kit (buggy)
do you ever feel like cutting up perfectly good parts just for the hell of it? i do, and today was one of those days. :mrgreen: so i'm looking through my little part drawers and stumbled upon my used losi a-1017 lxt/nxt steering knuckle setup. they've been in there for quite a few years after ditchi...
- Wed Apr 18, 2012 7:20 am
- Jump to forum
- Jump to topic
Re: Gear cover compatibility?
B4 ones fit well, and are twice as durable plus- work with the V2 slipper shaft
- Wed Aug 01, 2012 5:35 pm
- Jump to forum
- Jump to topic
Re: Truck front ends on OIN buggies
Picture worth 1000 words... 100_4196.JPG Bottom to top, AE "short" Arm AE (CE/Worlds Car) arm Andy's Wide Arm RPM "Team Car" (all the above are generally used with std nose plate) RPM "Worlds" arm (generally used with a 10T nose) Jeepz or Dynotech Arms (not shown, but m...
- Thu Oct 18, 2012 12:40 am
- Jump to forum
- Jump to topic
Associated 6 Gear Transmission Rebuild and Bearing Upgrade.
This thread is nearing completion. At this point I am just editing and correcting any mistakes. If anyone notices anything that should be changed please let me know..... I rebuilt an Associated 6 gear Tranny in the last couple of weeks. After wading through RC10talk.com I was able to find many helpf...