Does anyone know if there are currently and CVD's (3/16 wheels) on the market that will fit a T3?
Will the Custom Works Medium kit fit?
Last post
As well welcome. when you get a chance It's be great to see your project in progress.
Thanks for the info and the welcome. I'll have to figure out how to post pictures. I have an RC10 A-Stamp and RC10L from when I was a kid and recently picked up...
Ok I’ve finally gotten myself a GT, out of the many vehicles I’ve had and still have from over the years for some reason I just never bought one. So of course my first question is what did I get ? Would you consider this to be a black tub truck, or...
I bought my T3 just when the long chassis became the kit standard, but came across a short chassis/battery hold down that had be used as a mid motor dirt oval car. Wondering if the short T3 is the rarest of the breed. No pictures as the chassis is...
Last post
Thanks Jeff. I have got to dig out my B3/T3 chassis, I have the XL T3 in Carbon, as well as the composite from the kit. I also have the B2 SWB in carbon. I'll report my finds with measurements. Glad to have the three different battery straps in...
Hello. Was there ever a blue t2 chassis made, either factory or aftermarket?
Saw a picture of a t2 and the chassis looked blue. A lot of other parts are blue on the truck, so I know it’s entirely possible it was painted by the owner. Just didn’t...
Last post
Right on. Ya I’ve seen some cool ones here that’s for sure.
I bought a brushless motor and esc combo for my rc10t a while back. It's a 3300kv Hobbywing....
Last post
Just tried it out. I found I didn't have a 20 but I had a 21 tooth so I put that in. With cold road rage 2 tires it was all I could do to control it. Cold tires had a lot to do with it as we run them on our rc10gt s and have to get them warmed up...
Since the felt dust gasket is no longer in existence for the old stealth transmission on the RC10T (part 6566 on the diagram, which strangely comes up as a plastic cover on lots of sites). What is a good substitute. My felt cover is starting to...
Last post
Trademarks and copyrights expire. Also most of those logos used or even parts like chassis, towers etc... are from companies no longer in existence like hot trick, and novak. They have become discontinued parts/brands. Usually it would cost someone...
I'm new to Associated stuff, please bear with me. I know there are 3/16 & 1/4 rear axles, but what about these stubs that are both? I thought the 1/4 axles/wheels were 1/4 all the way through? Clearly these wheels are made for these axles since they...
Last post
I'm new to Associated stuff, please bear with me. I know there are 3/16 & 1/4 rear axles, but what about these stubs that are both? I thought the 1/4 axles/wheels were 1/4 all the way through? Clearly these wheels are made for these axles since they...
My RC10 T2 I raced at the 2021 Vintage Off-Road Nationals at RC Excitement
98663648-539F-4CB6-8D2A-EE9AB3C09296.jpeg
83EA4785-DC84-45F0-B083-7D47518A94A8.jpeg
T2 chassis
Vintage RC carbon shock towers
Big bore AE shocks
A&L steering set
New...
Last post
Its currently torn apart to get rebuilt for the 2022 event at the end of the year.
So I stopped into a local hobby shop yesterday looking for a B4/T4 top shaft to modify my T3 Stealth and I struck out. The owner caught up to me in the parking lot as I was pulling away and said he had this T4 in the back room he would sell me. I...
Last post
Generally the 10T and 10T2 bodies fit the T4's stock body mounts, the SC10 front body mounts on the T4 give you slightly more length if you need.
Here's mine on a T4...... it has a slightly different front tower but that wouldn't matter....
Hello all,
I don't have a problem, just a question on vintage associated part numbers.
I just picked up a nice condition t2 chassis off ebay and noticed that it has the 2 holes drilled for the mechanical speed controller. The other t2's i have do...
Last post
Going from memory… the 7011 sport truck was being sold as the entry level kit still when the T2 arrived in Team only form. Pretty sure it was towards the end of the T2 when the sport came out and took over entry level. Again, this is just from...
I have a few T3 runners so I have collected quite a few parts of the years. My daughter is getting to the age where I thought I'd put a truck together for her too. After digging thru my stuff I discovered I have enough parts to build a truck with...
Last post
Cool build you've got. I've become a big fan of the T3/B2/3 series over the past year. I am nearly done with my T3, and currently working on my B3.
That's nice! I believe you picked up a B3 from me in 2021. My all new build I did similar to my T3...
I had planned on running this after collecting some modern parts along the way. In the spirit of this JConcepts article here and on their website I figured an A & L Factory Works version would be cool to do. I do have the JConcepts steering rack and...
Last post
Is it the picture angle, or is that servo huge?
Its an Airtronics 94162z MG hi torque (115-144oz) servo. Yeah, the top case compared to a 94102 std servo is about 1/8 longer at top when comparing the at the servo mount. So far makes a great...
So, I purchased a Gt, got it at a great price as far as I am concerned. From the pics on the auction, it looked as though all it needs is a little tlc, and maybe a new engine. From the research I have done no biggie. I didn’t buy this thing to be a...
Last post
I always use a small pattern nut on the rear mounts anyways. I like that it keeps the mounts more secure.
I thought I would consolidate any pictures or discussions I wanted to share with the forum into one thread, for simplicity.
I'll start with my 10T from my original thread. I got this one running with some new electronics and a 550 motor and went...
Last post
any updates ?
I moved overseas for a number of years and it got put in a box for another time. I plan to revisit it next time I get a break from life, ha. My youngest liked your body however, and it lived on his T3.
A few words my Dad said after I told him we bought a house. That was 15 years ago. I did get the stuff out, and then sold off of my Losi electrics on Ebay (hopefully a member picked it up,was full of decent Jrxt bits). The only thing i kept was a...
Last post
Nice pair you have there
If only I had a dollar for every time I heard that during my time in prison... :roll:
Picked up this beauty on Crags list with a bunch of extra wheels and motors for around $135.
Loved my 10T back in the early 90's.
Came with a few Futaba Magnum radios as well.
Charged the oldazz batteries and whoosh they work!
Ordered a Reedy...
Last post
Nice score!
I really like those Toyota bodies so much I bought one off eBay
so ive been running a set of V2 shocks on my rc10gt brushless conversion with much success, i want to resurrect my T2 now that i can get rear arm mounts a lot cheaper than original
so my question is i want to modernize the T2 to club race, already...
Last post
so ive been running a set of V2 shocks on my rc10gt brushless conversion with much success, i want to resurrect my T2 now that i can get rear arm mounts a lot cheaper than original
I am looking to upgrade my recently converted brushless GT.
But...
Decided to finally build this rc10t early 7001 with non webbed arms and offset battery B stamp chassis. It was partially built and never finished and I have had if for a long time and had planned on using it for another 91 stealth build but I...
Last post
Here is a couple photos with the body just sitting on the truck. I have since trimmed up the back of the body and have the rear spoiler cut and ready to mount as well.
I thought I would share my experience building, track testing, and bashing my RC10GT brushless conversion. I've seen some really nice builds doing these conversions but could never find a whole lot about the end result as far as performance and is...
Last post
So far it's been very durable and very fast and when I consider that I only have a couple hundred bucks in the whole thing, I would do it again in a heartbeat.
What gearing are you using? Original 32 Spur right?
What pinion? I have a 48p 84...
Well.....
I kept telling myself NO but finally gave in. A friend gave me some money to order some stuff to fix up their kids slash, so I also added my stuff to the order as well to save on shipping. I couldn't resist Towers $40 discount and $14...
Last post
Welp I'm on to another project.
One many have done before me.
For any wanting to add a VTS to their vintage setup or build an
RC10GTE RC10EGT brushless conversion I have that one down now.
Picked this up on the FleaBay for the buck 09 without a...
Came across this thing a few weeks back. It's amazing how well these things can clean up. This took me about a night and a half, with not much more than an ultrasonic cleaner and a handful of beers. The chassis had a decent bend in it, but I was...
Last post
Thanks for all the information, Lobo. I'm still not sure if I'll ever do anything with this truck, but this is most helpful should I decide to.
I have read a bit here that you can upgrade your top shaft with the B4 slipper on an original 10T? can someone direct me to the correct parts needed for this? Thanks in advance.
Last post
I am running that on my sons car. Make sure you have the correct top shaft.
Note that this one does not have a built in spacer, similar to the kit original top shaft.
I had to put a bushing between the stealth transmission body and back of the triad...
I questioned them as being from the early 7001 shipment because of the information another member posted to the RC10T history thread. Has it been confirmed that did happen ?
I am new here. Haven't had a r/c truck since I was a kid and it was a original Tamiya Stadium Blitzer. Got it when it was brand new. Always remember seeing everything with the rc10 platform but couldn't afford it. 30 yrs later and I finally get one....
Last post
I was bidding against you on that truck 2.
I wasn't sure on much of it but it looks like an collection of some harder to find parts.
It looks to me like the rc10t composite craft chassis, RPM rear arms and technacraft turnbuckles.
Are there any obvious sources for truck 2.2 pin style rear wheels for the 3/16 axle? I haven't seen any available at JConcepts, Factory Works, or Schumacher but maybe I'm missing something. I'm not ready to convert to 12mm hex yet.
Need a battery cover pm me if anyone has one, doesnt have to be mint. 243023873_352565443284855_5207866442102251116_n.jpg 243008004_288023229822060_146143907607396927_n.jpg 243250410_4240591796067359_3984482972145000818_n.jpg...
Last post
Yea well when everyone else is shaking all the dirt out of their tubs you could spend that time squeezing off a couple more laps 8)
A good friend gave this to me,says he raced it a few times back in the day! I have had it in the closet for a couple years. I'm plannin on a full restore, will keep updates as i work on it. Enjoy!
Last post
Badd Boyz anodizing, quite a nice little time capsule you've got there.
Speaking of which I always wondered what happened to Badd Boys as it must have been a offshoot of a larger company.
I'm 29 years old, which makes the team moo Rc10t roughly the same age as myself. When I was probably 7-8 years old I saw a flash back post in a rc magazine on cliff letts Rc10t with the iconic cow front end paint scheme. Since that...
Last post
Beautiful truck, glad you are driving it and enjoying it. I too, have my version of Cliff Letts truck and have a thread on it here. I did buy carbon towers and Factoryworks rims inspired by the Jconcepts truck article on their website from 2017. And...
I am restoring my flat chassis GT and decided to go with the front end parts from the B4.2 so I can use hex adapters . I ordered RPM wheels for the electric Rustler and combined with the hex adapters from the B4 on the rear , there was barely axle...
GOT THIS BEAUTY OFF EBAY. YOU VERY RARELY EVER SEE ANY MODDED RC10T2'S AND THIS ONE I THINK HAS IT ALL LOL. MODS ARE LOSI WHEELS TIRES, RPM FRT BUMPER, MILLED CHASSIS,MOTOR PLATE, FRT BODY MOUNT AND BATTERY HOLDER, MIP BATTERY PAD, MIP SHOCK SHAFTS,...
Last post
Very cool truck! Would like to find a nicely lightened chassis. Most of the lightened chassis look terrible. If someone takes their time it can be very tastefully done and add to the uniqueness of the truck. Looks like you got a good one
Given the current price of Stealth transmissions, I couldn't pass this up. Total price was $140.
It has CVD's which will likely end up on my Team Truck.
The Tekin esc looks to be in good shape.
The shocks look like Traxxas, they'll be spare...
Last post
Wow! You’ve inspired me to tackle the heap I picked up. I had just about decided it wasn’t worth it but if I can get close to what you’ve done it will be worth it.
Hey there folks. I am so totally confused over the B6.4 rear aluminum hubs:
(
I don’t understand why, in the package, there are two hubs that are exactly the same side. It is as if there are either 2x left or right hubs in the packaging. Now this...
Hello all,
I recently purchased an rc10t2 for what currently goes for a good price. I'm interested in reading up on it as it seems like a really interesting truck.
It almost seems like it would be the equivalent of an rc10T worlds truck with lots...
Alright so a couple months ago my friend contacts me stating he just clicked buy it now on a sweet two vehicle package.
Cool what’d ya get now ?? Turns out he went for it because one was an all black parts Worlds car, both of them were clearly used...
Last post
Here’s the Airtronics transmitter that came along with it. 9F38A887-6392-44C4-B660-B78998878AD1.jpeg
I've been waiting on a day off for the past 6 months to sit down and really enjoy the build.
My camera is broken and can't focus so these are the best I can do.......
20200409_114129-1024x575.jpg
20200601_220502-1024x576.jpg...
Last post
Thx for the nostalgia! It takes me back to my '05 build. I still have it. I like how you mixed old and new, then topped it off with an original body. Looks sweet.
So I am running my Rc10t with the turnigy 1258tg with a reported 13.5 kg of torque.
At a complete standstill on pavement the front wheels are challenged and don’t fully turn. When driving it seems fine.
Should the wheels freely, or fully, turn...
Last post
The problem was the second servo saver I was using. I was using servo an older kimbrough servo saver instead of a servo horn. I swapped up to a standard piece of plastic and all is well now.
But it sounds like anywhere from 5-10 kg is going to be...
Does anyone else that is using the RPM ballcups have issues with them rubbing on the inner wheel when it is turned ? I’m using standard inline axles. I realize I can adjust the end point trim to prevent this but it affects the turning radius. I know...
Last post
I always ran the RPM ball cups and never had an issue with the rubbing...the strength of the RPM cup outweighed any rubbing...plus, as mentioned, end point adjustments and didn't need to drive at full lock much...
After searching and waiting many years I finally found a nice enough and original enough T2 I wanted for my collection. Ok so do I keep the Reedy Firehawk in it or go with something else ?
Leave the Futaba esc or install a still new Novak Racer I’ve...
Was there an entire conversion kit by Andy's to turn RC10s into monster trucks? I just received a sealed bag of Andy's parts (arms, bumpers, body posts, wheel adapters etc) but has no tag or markings. Ill post a pic of it later when I have a chance....
Last post
Sure does help! It also explains the Jeep Comanche body I got with it too!
Users browsing this forum: Facebook [Bot] and 9 guests
Forum permissions
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot post attachments in this forum
Facebook [Bot] and 9 guests