With the amount of these that are being purchased, there will be a flood of build threads coming. We don't want the new car to bury the o.g. new builds, replicas, restorations, etc., that already take place in our buggy forum. So the best thing to...
What 7.4V 2s battery is everyone running with a brushless/lipo setup that fit in a standard RC10 classic rear bulkhead?
Are people just running shorty packs with foam spacer?
I am struggling finding a pack that meets the standard dimensions. I...
Last post
I also run a shorty in my gold pan, but run the one linked below in my worlds rere... which should fit the same as the classic. They fit the bulkhead and battery cup perfectly and have plenty of punch for a 50C (as much as my other 90C packs).
I got my Re-Re in the mail yesterday and I am super excited. I am going to build it and shelf it next to my Cadillac. Anyway, I was looking over the chassis and it seems a bit... off. I have a few pictures. Should there be the ridges and...
Last post
I find it very hard to believe that the re-re is of a lesser grade than the original. Should all be top notch stuff :wink:
I've read enough reports to make me feel that there were some substantial quality control issues. How about the top shaft...
Ok, so finally received mine since it was shipped to Mo (old address) instead of NY. Was excited like a little school girl when the box came in. One minor issue, the air pack shipping things failed and the box got a dent in it. No damage to the car...
Last post
Ok, so this car was raped for Re Re parts for my American Sprint Car. It's slowly starting to come back together though.
I'll try to fix the earlier pics later. But it's changed so much...first I was going to do a stock, then slightly...
I got my worlds today so I figured it would be a good time to figure out wtf Associated did. I have three scenarios all played out
-stock worlds case and idler
-6565 case with worlds idler and extra bearings
-6565 case and 6570 idler (aka how it...
Last post
I'm in the middle of building a worlds car too. Mine seemed to have a bad top shaft. I put one in from an old T4 transmission I had laying around and viola! Smooth operation.
Overall, I'm a little disappointed at the quality of the materials...
For some reason I was content to watch everyone else build theirs when these first got into our greedy little paws, but didn't feel the motivation to start mine! I also waited for a few of the hop up parts I wanted for it and the painted body and...
Last post
Great work!, came together nicely, paint is awesome!
I'm looking for opinions on which tranny would work best for my re-re World's car this spring. My local track isn't huge and somewhat technical, but I've heard the owner will be making it larger this season. It's a fiarly high-traction track with...
Trying to determine for the electronics of the car.
Last post
Hi,
I wish someone had told me, about the 8.5 turn brushless limit. :roll:
well, if you had read the manual, it is there in print. This was just a recommendation, if you choose to exceed it then fine! Its not a rule. The gears are not meant to...
I broke down and bought the Worlds kit. I was going to go with the mono shock up front that I got from Jeff (Thanks Again! :D ) but after mocking it up, realized the front tube supports were going to be in the way and not having them on their just...
Last post
Finally after over a month of waiting AE sent me replacement parts! :D
They actually sent me two top shafts too. Not sure why but I will take it.
Case part # 6565-001
Idler shaft and gear part # 6570-001
Top Shaft B4/T4 part # 9601
Does anyone know for fact if this is gonna happen?? Will it be molded in white or black? Thanks for any info.
Last post
Yes, but as I showed in my video the idler is most of the problem :wink:
FYI, there is a guy that is making a replacement Idled gear for the new China stealth transmissions. The gears are aluminum and worked great in the tranny. It's a lot...
HI!... Just picked up this Team Associated RC10 World's car (re/re).
Last post
Looks good but i would switch out the front axles to the 6220 rc10 axles with those wheels since they are a different offset than the kit front wheels.
Is AE doing any more re re's of the cars or 10T?
I see Tower has discontinued the stealth tranny and no longer has the Worlds car on the site.
I was hoping for a re re graphite and 10T.
Any one in the know?
Last post
I would buy 2 sets of rear DS arms if they re-re'd them. :P
thanks for accepting me in the forum. I write from Milano, Italy. I would liked to ask your help:
I bought the RC10 classic re-release. Can you please suggest me the list of components ( Motor, esc, servo, batteries) that you think that...
Finally got around to it, as I just couldn't pass on one at $199 shipped from AE.
Decided to leave the chassis stock for now, see how it does. Opted for one of Atomik Racing's HD1207TG servos, as I've found this product line to be excellent...
A good friend of mine who's into off-road racing convinced me to get a car together for a local track on October 11th. Since I've had my World's Re-re collecting dust since I bought the kit, I decided to give it a shot. I've never raced off-road...
Last post
That's a Masami style left turn. 8)
The buggy looks great and very retro with the pink.
So as the Losi guy I am, I just got a NIB Worlds kit I havent had a new RC10 in 20 years, is their any info or advice I should no before I build it? things I should door order to fix any short commings with the kit. mine has the upgraded trans parts...
Last post
Thats it. The stock worlds case has a different part number (6564)
6565 is old moulding USA case
6564 is new improved China case
Now that the anodized parts for my ReRe projects are in, it's time to get building!
I think I have most of the parts on hand to complete this one except for the new Lunsford Worlds Retro turnbuckles I just ordered and maybe a few other little bits...
Last post
what rear shock tower is that I like the wing mounts?
The rear tower is just a short World's 3mm tower from RC Carbon Works. The wing mounts are from the B5M kit (91531).
...The car is gorgeous, very stunning. Love the colors.
Looks good! ...?...
Hey all, this is first post territory, so go easy on me!
I've recently bought an original RC10 (at this stage don't know what stamp it is, will find out when it arrives) and I want to do the shell as per the box art, as those ads in the 80's really...
Last post
Excellent, thanks for that Scr8p!
Incidentally, is the pro-line body (available from the AE website) accurate to the original? I know that the classic had different webbing, but considering I'll be cutting that away, its not an issue for me.
It all started with the thread that Cedric did on his replica of Brian Kinwalds 1993 WC car.
I've read that thread over and over again and it's such a beautifu car.
Now with the rere of the world's car I immediately put down a pre-order and waited...
Once the shock bottom cap is tightened the shaft is so misaligned it won't move! :evil:
Anyone else run into this?
Hard to get a good photo, but
A link to the video showing the movement
Last post
Simple, just remove the shock shaft and orings, run a drill bit thru it, wobbling side to side to clearance it, then reassemble. That's how the (eBay) pros do it :lol: Lmao!
That's probably one of the first shock bodies I have seen misbuilt....
Just picked up a World's Car in the recent discounts. Decided to go with a FT blue screw kit for it. I did end up needing a new top shaft as the one that came with the kit was just not smooth. Here are a few pics of the build so far.
Only have one re-re completed so far and with the little bit of a run going on here with worlds car posts I thought I'd add mine to the mix. Kept it stock except for white wheels, RPM gear cover and Steve's front bumper. My kit also had the bad...
Last post
Thanks! Paint was by Larry at Kustom R/C graphics. I was going for a boxart-inspired scheme but not a copy. The final product wasn't exactly what I asked for but I still like it. It's hard to explain in an email every detail so until I make attempts...
Stupid question, has anyone had luck at tightening up the steering on the Worlds I have replaced the bell cranks with JConcepts and replaced the servo horn with a metal horn. I have a metal geared servo (Savox). It turns great, it just seems like it...
I have a worlds re release kit and have pretty much built up as much as I can. I am being sent a replacement top shaft as it was one of the incorrectly machined ones.
That aside the next issue that I have is that none of the servo horns...
Last post
I also bought a losi aluminium horn as a replacement should the kit one strip. The kit horn is holding up so far
I never had a chance to upload a pic of my car. So this is my Worlds RE RE. It's a very stock and meant to be a car to race here and there and drive laps at the track. So after driving at the track 5 times I have managed to shear the left bell crank...
Last post
Got the screws in other days, and they work great. The guys from Chief's were great to work with.
The thing just took off by itself...5700kv geared high
Goes across a parking lot full throttle into the curb. It smashed the curb at like what must've been at least 50...the tires are screaming, it...
Last post
LOL
.....yeah......hopefully she runs anything BUT the same.
Hi there, I have a rerelease worlds car on order and fully intend to race it against modern buggies and also maybe in the vintage class if we have enough cars.
I normally race a dex210 mid motor car and the general tyre that works at our track are...
Here are a few pics of my RC10 Re-Re runner. Wanted to keep it mostly stock. Only upgrades are JConcepts bellcranks and 2.2 inch wheel conversions. Let me know what you think!
It's been a while! For the past year I have committed to pursue my Master's Degree and now I read a book a week and write a paper a week. Being a dad is number 1 for me so I have to guard my time and sometimes I feel pretty overwhelmed. This...
Last post
The whole job is beautiful. The paint job is crazy good. Amazing mate
So even though I still have no precise idea about where I'm going with this one, I thought I would already share what I have gathered so far. I was not that enthusiastic about building this one, but since I have two and never had the opportunity...
Last post
That thing looks sweet!!!
Before I read the comments, I was of the same mind state. I'm not a fan of the detonator myself , but as soon as I saw that pic, I was telling myself that body looks freakin good .
Looks night and day compared to some...
I built this when they first came out a few months back...Beat on it (pretty hard) ....
It was time for a clean up and a few hop ups....Tryin to make her nice n purdy.
Figured I'd take a few pics early today cause I knew she wouldn't stay clean...
Last post
Ah man.....this is kinda heinous.
(Rookie mistakes)
Why did you have to point that out.....n it's freshly glued too.
Now I'm gonna have to go buy another set of tires......
Now that you pointed it out, it's sticking out like a sore thumb.....A...
Question, in my son's re-classic . We are currently running a Radon 17.5T brushed. I am thinking about converting him to a brushless motor. I am thing about either running a Hobbywing EZRUN Combo SCT, Castle Creations Sidewinder SCT, or Tekin 17.5 T...
Last post
I hear you.....I don't like anyone driving my rc10's....
I don't wanna drive their car....n I don't want them to drive mine.
If there's damage done, it's gonna be my damage.
My Slash, I'll let anyon drive that. The Rc10s are a different story........
So i went into a local Hobby Town yesterday and was talking to a kid in there about vintage stuff and he said they had got a couple of gold pan re-re's back in december but never sold them, so they were actually boxed up and going back to the...
I am finally getting around to putting up pictures of my first RC10.. I decided I would get one as this has all the parts I would buy anyway to create my RC10.. It was a good price with the coupon and free shipping from Tower so I bit the bullet.. I...
Last post
Why thank you.. :) I'm pretty happy with how it turned out.. After 20 odd years I finally have one.. next rc10 will be a short arm with a 6 gear.. that will ccome in time.. 8)
Hi all,
I have been out of RC since oh the late 1980s and just received a rc10 classic as a gift. I never had one back in the day (got a clodbuster for xmas instead) but I always wanted one. I know nothing of current RC requirement so was hoping...
Last post
98 SVT? I used to have a silver 1998 Contour SVT, would be a small world if you had one.
Follow the advice of these guys. I was in a similar boat when I rediscovered RC a few years back and wasted time dealing with am radios and interference,...
I built my Classic over Xmas break, completely stock except for a full set of bearings (mix and match, some new, some old), ordered up a new Novak Edge ESC and 17.5 turn brushless motor for it... and couldn't bring myself to run it. Or even paint...
Last post
the re-relreases were made to get people racing them again, so you're doing it right :).
On a trip to vegas got to go to a car museum and see a few lemans racecars from the 90's. they were in great shape, but After looking at them long enough I...
My RC10 rere worlds car have meshing issue just like most of you guys. I've tried all methods of sanding down the idler,
running in etc.......i realise there is no way i could get it to run the way it should. Then I spoked to a few of...
Last post
The problem also might be a bad transmission case. I sent my transmission to AE for the same reason and they concluded that the case was the issue. It has been replaced and the transmission is on it's way back.
Hello all, this is my first post here. I picked up a re re worlds car for the nostalgia thinking that I would run it occasionally. Then I ran it and saw how good it handled and how fun it is to drive so I am thinking of racing it. Now the thing is I...
Last post
B44 axles are still too long for use with stock arms and B4 rear hubs, you need a Yokomo Bmax2 rear bone to make a hybrid cva. You'll still need a custom works spacer and B44 front low profile nuts.
She's all done. Mines getting dirty no time for a shelf queen haha!
Last post
I think its awesome how good they handle. Just got done with mine and the first time I ran it I was amazed at how it handled. I was thinking when I bought it that I would run it every once in a while but I am definitely going to race it. Yours looks...
Users browsing this forum: No registered users and 9 guests
Forum permissions
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot post attachments in this forum
