The ball studs that hold the front sway bar on my RC10 have broken off leaving the threaded part inside the front A arms . Any good tips or tricks to get the pieces inside the A arm out without ruining the arms? Also, provided I can get them out, what is the part number for the ball studs? I have the edinger manual but it lacks all the part numbers for the screws.
Thanks in advance.
Removing broken sway bar ball studs?
-
THEYTOOKMYTHUMB
- Super Member
- Posts: 6814
- Joined: Wed Oct 22, 2008 5:15 pm
- Location: Evansville, IN
- Has thanked: 2122 times
- Been thanked: 1346 times
Re: Removing broken sway bar ball studs?
Dremel with an engraving head.AndrewSi wrote:The ball studs that hold the front sway bar on my RC10 have broken off leaving the threaded part inside the front A arms . Any good tips or tricks to get the pieces inside the A arm out without ruining the arms? Also, provided I can get them out, what is the part number for the ball studs? I have the edinger manual but it lacks all the part numbers for the screws.
Thanks in advance.
Oh, and safety glasses.
"The world looks so much better through beer goggles: Enjoy today, you never know what tomorrow may bring."
Ken
Ken
Re: Removing broken sway bar ball studs?
Bump!
Does anyone know the part number for the correct balls studs for the front sway bar on a gold pan?
Does anyone know the part number for the correct balls studs for the front sway bar on a gold pan?
-
rctenracer
- Approved Member
- Posts: 1280
- Joined: Tue Dec 30, 2008 3:02 am
- Location: michigan
- Been thanked: 87 times
Re: Removing broken sway bar ball studs?
Dubro 2/56 ball studs will work. I just used parts out of the two listed to make a complete sway bar set up.
http://www3.towerhobbies.com/cgi-bin/wti0001p?&I=LXD897&P=7
http://www3.towerhobbies.com/cgi-bin/wti0001p?&I=LXD899&P=7
http://www3.towerhobbies.com/cgi-bin/wti0001p?&I=LXD897&P=7
http://www3.towerhobbies.com/cgi-bin/wti0001p?&I=LXD899&P=7
-
klavy69
- Moderator
- Posts: 5150
- Joined: Thu May 29, 2008 4:11 pm
- Location: Fulton, IL (Land of one stop light but we DO have a windmill!)
- Has thanked: 561 times
- Been thanked: 265 times
Re: Removing broken sway bar ball studs?
New arms would be easier
Todd
Todd
Peace and professionlism.....Kabunga signing off!!!
Re: Removing broken sway bar ball studs?
Awesome! Thanks guys. Those ball cups look to be the same aswell. 
Create an account or sign in to join the discussion
You need to be a member in order to post a reply
Create an account
Not a member? register to join our community
Members can start their own topics & subscribe to topics
It’s free and only takes a minute
Sign in
-
- Similar Topics
- Replies
- Views
- Last post
-
- 7 Replies
- 1017 Views
-
Last post by hellbelly
-
- 3 Replies
- 1194 Views
-
Last post by DrumAnBass
-
- 2 Replies
- 715 Views
-
Last post by HDMM
-
- 7 Replies
- 1146 Views
-
Last post by scr8p
-
- 4 Replies
- 888 Views
-
Last post by DMAT
-
- 1 Replies
- 502 Views
-
Last post by civilguy
-
- 8 Replies
- 1527 Views
-
Last post by radioactivity
-
- 4 Replies
- 553 Views
-
Last post by y2kgtp
Who is online
Users browsing this forum: No registered users and 17 guests