Slipper thrust bearing?

Moderators: scr8p, klavy69

Post Reply

16 posts

adam lancia: Approved Member; Posts: 1116; Joined: Tue Feb 05, 2008 6:37 pm; Location: Donkin, Nova Scotia, Canada; Has thanked: 7 times; Been thanked: 41 times

Re: Slipper thrust bearing?

Quote

Post by adam lancia » Thu Jan 16, 2014 9:26 pm

You're right! Thanks for the memory jog. It's been a while since I've had my grubby paws on any RC stuff

Post Reply

16 posts

Create an account or sign in to join the discussion

You need to be a member in order to post a reply

Create an account

Not a member? register to join our community
Members can start their own topics & subscribe to topics
It’s free and only takes a minute

Sign in

Similar Topics

Replies

Views

Last post

Replacement options for slipper clutch thrust bearing

Last post by juicedcoupe « Sat Jun 26, 2021 9:56 pm
Posted in RC10 Buggy Forum
Replies: 4
by jbmeyer13 » Wed Aug 26, 2020 11:27 am » in RC10 Buggy Forum

First post

While servicing my V1 slipper clutch the thrust bearing which sits between lock nut and spring lost its bearings. I can’t find the original part for sale anywhere (asc 6586) or the replacement (6594) and I’m wondering if there are any suitable work...

Last post

Bringing an old thread back up, and thought I'd throw out a couple options I'd found.

1st. Fast Eddy 3X8X3.5 (F3-8M) bearing. Luckily I ordered two sets to try, because only one outer race from each fit. I tried drilling the race but they are...

4 Replies

1516 Views

Last post by juicedcoupe
Sat Jun 26, 2021 9:56 pm
Thrust Bearing

Last post by Tamlok « Tue Sep 05, 2017 8:26 pm
Posted in Temple's RC10 Tech Forum
Replies: 2
by Tamlok » Tue Aug 29, 2017 9:34 pm » in Temple's RC10 Tech Forum

First post

Has anyone tried using this style thrust bearing?

I needed some bearings and saw this so I thought I would try it out. Its installed but I have not run the car yet.

Last post

Sure does look like it, but I can assure you the grooves are facing the balls. Bad lighting and picture compression doesnt help.

2 Replies

876 Views

Last post by Tamlok
Tue Sep 05, 2017 8:26 pm
AE 3434 Thrust bearing

Last post by sandkil « Wed Apr 09, 2014 9:38 am
Posted in Temple's RC10 Tech Forum
Replies: 3
by sandkil » Wed Apr 09, 2014 4:43 am » in Temple's RC10 Tech Forum

First post

Hey!

Does any one know where to find asc3434 thrust ball bearing set, 1/4 ID x 9/16 OD for RC12L rear axle?

//Erik

Last post

if that is the size you want, this one might live longer

Hmmm.. Now we're talking :)
Thanx man

3 Replies

711 Views

Last post by sandkil
Wed Apr 09, 2014 9:38 am
thrust bearing washer??

Last post by marlo « Sun Jun 23, 2013 1:58 pm
Posted in RC10 Truck Forum
Replies: 5
by slvrback » Sun Jun 23, 2013 8:57 am » in RC10 Truck Forum

First post

Was looking arounnd online this morning and saw this on fleabay. Says it improves the diff and gives it more punch?? Anyone have any idea what that means?

Last post

The thrust washers also went through a change. They used to be a hard type chrome finish, and now a black oxide finish...just putting it out there :mrgreen:

5 Replies

1101 Views

Last post by marlo
Sun Jun 23, 2013 1:58 pm
Look what happened to this Thrust Bearing

Last post by superfly « Thu Jan 18, 2007 9:07 pm
Posted in RC10 Buggy Forum
Replies: 6
by superfly » Thu Jan 18, 2007 6:26 pm » in RC10 Buggy Forum

First post

I just pulled this out of an RC10 I bought off ebay for parts. I think the car probably has 2 or 3 hours total time on it as it was assembled with mistakes all over it and the performance must have been terrible...Just look at the wear on the thrust...

Last post

OK yeah you're right I think that blue thrust washer is cooked too...I'll get a new set just to be sure...cheers!!! :lol:

6 Replies

939 Views

Last post by superfly
Thu Jan 18, 2007 9:07 pm
anybody have an a-3011 thrust bearing?

Last post by aconsola « Tue Apr 19, 2011 12:06 pm
Posted in Losi Forum
Replies: 4
by aconsola » Sat Apr 16, 2011 8:07 pm » in Losi Forum

First post

the a-3011 is the original thrust bearing that shipped in the first release of the jrx-2. subsequent versions had the new thrust bearing which changed part# to a-3018. The jrx-T production release edition of the manual lists only the 3018 part.
I've...

Last post

thanks.
With all of the losi cars I've gone through over the past 6 years since I started collecting I've never come across one of those.

4 Replies

753 Views

Last post by aconsola
Tue Apr 19, 2011 12:06 pm
Topcat/Cougar Thrust Bearing

Last post by kaszal « Fri Mar 23, 2012 8:25 am
Posted in Schumacher Forum
Replies: 13
by RCveteran » Sat Apr 02, 2011 12:39 pm » in Schumacher Forum

First post

I thought I read Losi ones will work, one on left is Schumacher and 8mm across, all the Losi ones I have are like the one on the right and 10mm. Anybody know of something that is the 8mm size? DSCF4716.JPG

Last post

No problem but the Procat diff axles are definitely 1/8 (3.2mm) so that's good to know both the T-Rex thrust washer plates fit.

13 Replies

1596 Views

Last post by kaszal
Fri Mar 23, 2012 8:25 am
Thrust bearing on hydra-drive?

Last post by Bongo Fury « Sun Jan 11, 2009 4:00 pm
Posted in Losi Forum
Replies: 1
by aconsola » Sun Jan 11, 2009 2:06 pm » in Losi Forum

First post

What's the point of the thrust bearing on the hydra-drive setup?
The outer part of the hydra where the thrust bearing contacts is keyed to the shaft, so it cannot rotate with respect to the shaft/spring/fixing screw.
If anything, it would make more...

Last post

I'm with you, don't see the need for the thrust bearing either. Or a spacer for that matter, I just screw the nut on further.

About all I can see is its a handy place to store the bearing if you want to drop the Hydra quickly.

1 Replies

347 Views

Last post by Bongo Fury
Sun Jan 11, 2009 4:00 pm

Return to “Temple's RC10 Tech Forum”

Who is online

Users browsing this forum: No registered users and 11 guests