thanks guys. hopefully i'll have this all buttoned up by next weekend. i have figure out which jps wheels i want to put on it, and that should be the last thing i need to get.
Damn that thing looks nice. I have a whole slew of stuff I have been saving to do a build like yours. Are you going to dye the parts or leave them white?
everything that's white, is gonna stay white. it'll be kinda like the boxart worlds car. the steering knuckles and caster blocks are white, too. they'd be on already, but i forgot to grab some hinge pins when i was at the lhs.
i got 2 sets, but broke one of them up. the front is on my tekin chassis, and the rear is on my andys chassis. wait till ya see how i mount the tops of the shocks on the andys car.
Here are some pics of what I will be using in this build
Last post
sweet car sho!! I have a question in regards to the hydra drive slipper. Is it anything special? I am just asking because I got a jrx2 roller a while back and it had one on it. And I have never seen one before. thanks
I got really excited a couple of years ago when I heard they were going to reproduce some of their old RC parts. I liked them on Facebook to get updates, but all I see are pictures of custom made knives. I send them a message and all they could say...
Last post
Team Composite Craft what a joke.. thanks for reminding me to unlike them . i think everyone should unlike them, maybe they will get the hint
I stumbled on this a few days ago. I emailed them and they said they will have the laminate available sometime in the new year with some highly sought after parts and maybe a new car later on.
Good luck to them!
Last post
I have an RC10, RC10T and LX-T LTO chassis that I would donate to use for patterns. :wink:
Hello Everyone! Well its been in my collection long enough and i couldn't look at it unbuilt any longer. This did however take me the longest of any other project to locate the needed parts but was well worth the wait. This is what i have done so...
Last post
I think having some of these parts machined in delrin would probably be a far cheaper method of having them recreated.
chad smith form dynotech was working on that but i don't know how far he ever got.
Hey guys, just wanted some opinions with what you have done to the rear bulkhead to make it fit with the a-arms. Also I am running into some clearance problems with the upper deck hitting the rear shock tower... what did you guys do? Any suggestions...
Last post
couple different examples. all black rig shows stock tower and just clearancing the area under the upper deck screws, keeping the gap overall nice and tasty (imho). second pic shows how little of the stock bulk really needs to be trimmed.
I have a nib Composite craft worlds chassis and would like to build and complete it. I have found some photos and other info on here, but still have qhestions. I know that a rc10t or gt front bulkhead will be needed. What arms do i use and do they...
Last post
no, it's a worlds chassis. it could just be an early version..... or something like that.
382DC00E-DCA5-446B-8491-DA59FC32D57C.jpeg 50FC9EFE-0C06-4362-BF9D-C272E469498E.jpeg 30601915-3351-4C9E-BC80-7C5D95311162.jpeg F5B2EFD3-9AF3-491B-BE4E-869100C4800C.jpeg 98195991-E654-4F73-8EDA-5FAE4C67217E.jpeg
Finally had the chance to check this...
Last post
RPM didn't have a truck bulkhead that accepted nose tubes. The one you have is it, so ultra molded or carbon chassis is about it.
Been a while, but building a Re-release worlds car with RPM worlds wide arms based on a composite craft chassis. The purpose is to compete in a local vintage race with an edge on the competition !
More details and a complete Bill Of Materials to...
Last post
Finished it minus the electronics. Figured I'd share some pics. I ended up scoring a used original RPM worlds car and pulled the suspension arms / mounts off that and put it on the composite craft chassis. I went with my old colors I used to use...