Like many of you I grew up drooling over the RCCA article of Cliff Letts Team Moo RC10t. I was fortunate enough to get a 10t in 92 as a kid but never the funds to duplicate that dream truck till now.
I was browsing OfferUp awhile back and I was in the right place at the right time to score this gem and parts for 50$ Needless to say I was elated with the buy and it’s thoroughly sent me down the vintage RC rabbit hole.
The truck is mostly completed at this point but I wanted to document its build here and give back a little something to this site which has been invaluable with information for me.
I will continue to update this as my time permits but here it is in all its “glory” when I bought it..
So I started the teardown process to clean up what I had and identify parts that I needed as some were missing…
-Front bumper was missing
-Inner slipper clutch hub was missing
-Steering servo arms were both cracked and needed replacement
-Tie rods were all rusty, one was broken and need replacing
Little simple green and warm water did wonders… Then I read about the peroxide process here and did that as well. This Pic doesn’t do them justice, they came out like new!
So I had my “shopping list” and went about paying way to much $$$ for those missing parts on eBay and other FB pages but I didn’t care I was building my childhood dream after all… This is where I started taking liberties as I wasn’t building a exact replica of Letts truck but what I wanted it to be today… I wanted it to be a runner and race it at a local backyard track “The Farm” which ironically I’d never been to and still have yet to go…
So over the next couple months I bought and stock piled a bunch of rad stuff for the build:
- The missing front bumper, dog bone and clutch hub
- Jconcepts steering setup, nose piece and 10T body
- Lunsford super duty 3.5 titanium tie rods
- VintageRC carbon towers F/R and rear brace
- RPM arms F/R, rear hubs, rod ends and gear cover
- Set of OG front skinnys and rear wheels/tires in great shape at a surprisingly good price compared to some of what I bought..ahahaha
- MCI decals
- KNK screw kit
Also during that time was researching PC colors so I could get the chassis done….. Boy was that an ordeal…
At this point I had most of the parts for the build I just needed the chassis PC’d that iconic fluorescent red…
After searching looked like there were two options that seemed close to the original color going by pics.
PPG fluorescent red and a shop out of Florida, APP that had a “Luminous Neon Red” that seemed more vibrant than the sample PPG I got, so I went that route…
Note: I bought the PC myself because the local PC shop I was going to use didn’t have this color and I could source quicker than they quoted and they adjusted price accordingly.
Anyway, dropped off the PC, chassis and two nose plates the off. Week goes by and I get the call there done! Get down there and the nose pieces were really lite colored and not a consistent color compared to the chassis. So I take the chassis and they will redo the nose pieces… Another week goes by and I get the call, they look better-ish so take em home and once I put them next to the chassis NO GO as you can see in the pic… they just coated over the first stuff they did so they were WAY too dark and weren’t even the same between the two..
So back I went again, another week and they matched the chassis and looked good enough for me… sorry no pics tho
Almost forgot about this… here is a pic of the nose piece and chassis finally matching..
Also found some more parts:
-Jconcepts motor plate
-T4 top shaft and VTS slipper
-Reedy Mr A’s motor
-Novak 410-M1c
And pics of how it sits currently. Still looking for a couple stickers and a Novak receiver but in no hurry as I’ve got several other projects going right now…
Andybellus wrote: ↑Mon Aug 21, 2023 7:36 pm
At this point I had most of the parts for the build I just needed the chassis PC’d that iconic fluorescent red…
After searching looked like there were two options that seemed close to the original color going by pics.
PPG fluorescent red and a shop out of Florida, APP that had a “Luminous Neon Red” that seemed more vibrant than the sample PPG I got, so I went that route…
Note: I bought the PC myself because the local PC shop I was going to use didn’t have this color and I could source quicker than they quoted and they adjusted price accordingly.
Anyway, dropped off the PC, chassis and two nose plates the off. Week goes by and I get the call there done! Get down there and the nose pieces were really lite colored and not a consistent color compared to the chassis. So I take the chassis and they will redo the nose pieces… Another week goes by and I get the call, they look better-ish so take em home and once I put them next to the chassis NO GO as you can see in the pic… they just coated over the first stuff they did so they were WAY too dark and weren’t even the same between the two..
So back I went again, another week and they matched the chassis and looked good enough for me… sorry no pics tho
Sorry for chiming in late but what was your PC cost? I'm in So Cal and want to get some older chassis rehabbed.
Andybellus wrote: ↑Mon Aug 21, 2023 7:36 pm
At this point I had most of the parts for the build I just needed the chassis PC’d that iconic fluorescent red…
After searching looked like there were two options that seemed close to the original color going by pics.
PPG fluorescent red and a shop out of Florida, APP that had a “Luminous Neon Red” that seemed more vibrant than the sample PPG I got, so I went that route…
Note: I bought the PC myself because the local PC shop I was going to use didn’t have this color and I could source quicker than they quoted and they adjusted price accordingly.
Anyway, dropped off the PC, chassis and two nose plates the off. Week goes by and I get the call there done! Get down there and the nose pieces were really lite colored and not a consistent color compared to the chassis. So I take the chassis and they will redo the nose pieces… Another week goes by and I get the call, they look better-ish so take em home and once I put them next to the chassis NO GO as you can see in the pic… they just coated over the first stuff they did so they were WAY too dark and weren’t even the same between the two..
So back I went again, another week and they matched the chassis and looked good enough for me… sorry no pics tho
Sorry for chiming in late but what was your PC cost? I'm in So Cal and want to get some older chassis rehabbed.
Was a 100 minimum charge(seems most are around this cost) but I ended up sourcing the PC so they charged me 60… With all the hassle and issues with them getting it done/matching I’m not sure I’ll go back to them..
Andybellus wrote: ↑Mon Aug 21, 2023 7:36 pm
At this point I had most of the parts for the build I just needed the chassis PC’d that iconic fluorescent red…
After searching looked like there were two options that seemed close to the original color going by pics.
PPG fluorescent red and a shop out of Florida, APP that had a “Luminous Neon Red” that seemed more vibrant than the sample PPG I got, so I went that route…
Note: I bought the PC myself because the local PC shop I was going to use didn’t have this color and I could source quicker than they quoted and they adjusted price accordingly.
Anyway, dropped off the PC, chassis and two nose plates the off. Week goes by and I get the call there done! Get down there and the nose pieces were really lite colored and not a consistent color compared to the chassis. So I take the chassis and they will redo the nose pieces… Another week goes by and I get the call, they look better-ish so take em home and once I put them next to the chassis NO GO as you can see in the pic… they just coated over the first stuff they did so they were WAY too dark and weren’t even the same between the two..
So back I went again, another week and they matched the chassis and looked good enough for me… sorry no pics tho
Sorry for chiming in late but what was your PC cost? I'm in So Cal and want to get some older chassis rehabbed.
Was a 100 minimum charge(seems most are around this cost) but I ended up sourcing the PC so they charged me 60… With all the hassle and issues with them getting it done/matching I’m not sure I’ll go back to them..
Very nice! I built one of these myself and it is one of my favorites
Thank you! Same here. I am a huge fan of the late 90's and early 00's 4wd's. I have this one, a Yokomo YZ10 95', and a TTech Predator 95 International Edition, and a JConcepts...
You didn't think I tracked down the manual just for the fun if it, did you?
Here is the goal:
This will be a slow process, the rear was pretty simple so I knocked it out today. Just a different order of build from stock with a unique...
Last post
Ahh ok, that’s cool. Ken is fairly chatty on Facebook so when I saw that name I got excited. In my mind it could had been possible as the car came with delta shocks as well.
Couple more screenshots that don’t apply here but I don’t have a place for...
Finally got a chance to start my 10T rebuild. Everything cleaned and started to reassemble. I added new RPM front bumper and nose plate. I have new tires and wheel, new team shocks and new RPM arms on the way. I think im going to add an RPM tranny...
Last post
Being black and white like the worlds cars you have you ought to put a worlds chassis and have a worldsT lol Don
ps> i got yellow front wheels and tires for it lol :lol: 8)
starting to build a racer so i can start racing again, i got this truck when i was 3 and raced it for a couple years when i was younger then it just sat in the garage. i recently grabbed it and started to build it so i can race this coming season....
A huge thanks goes out to My friend Devon (Dcar) for the tip on these wheels. He saw them on craigslist and knew he wasn't going to be able to pick them up for himself so he took one for the team and gave me the call. I had to walk out on a dinner...
Last post
Superb build Shodog.
I will try and post some of my projects as soon as I can handle the posting part on here. 8)
So after finding out that all the traction aids and oversteer correction mods I did on my Prolite 4x4 to make it better on my home outdoor dirt track really worked against me on the local indoor clay track, I decided I needed to build a nice little...
Last post
BTW, if anyone has FT graphite/CF towers for this thing they wanna sell, I'd be interested.