Search found 323 matches

by metallicats33
Wed Jul 22, 2009 9:44 pm
Forum: RC10 Buggy Forum
Topic: Metal gears for the original stealth
Replies: 10
Views: 2919

Re: Metal gears for the original stealth

i have used this idler in one of my brushless runners and it works well. you gotta use a lot of black grease though. once the top shaft wears in with the steel idler the noise will subdue. good luck!! that's what I wanted it for, Brushless. If all it damages is the diff then thats cheaper to replac...
by metallicats33
Wed Jul 22, 2009 12:28 am
Forum: RC10 Buggy Forum
Topic: Metal gears for the original stealth
Replies: 10
Views: 2919

Metal gears for the original stealth

just wondering if adding the Robinsons Racing Optional Steel Idler Gear for the RC10-GT to my rc10 stealth tranny is a good or bad idea. The stock Idler gear for the Rc10 and Rc10-gt are the same part number (6507) so I assume the steel gear should fit in the rc10 stealth. has anyone used this befor...
by metallicats33
Sun Jul 19, 2009 1:58 pm
Forum: RC10 Buggy Forum
Topic: CVD keeps coming out of out drive
Replies: 11
Views: 1506

Re: CVD keeps coming out of out drive

You could also fill the holes in the graphite chassis and use a template to re-drill and countersink the stealth mounting holes.It is a easy repair. I have used jb weld and also panel bond to repair holes in a few resto's and have had no problems as far as strenght goes. I think the panel bond is m...
by metallicats33
Sun Jul 19, 2009 3:14 am
Forum: RC10 Buggy Forum
Topic: CVD keeps coming out of out drive
Replies: 11
Views: 1506

Re: CVD keeps coming out of out drive

well I was going to take a few pictures as suggested but.... I was looking over the car one more time and noticed that the previous owner (my friends dad) drilled the stealth holes just a hair off. They are just a tad over to the right, just enough for the left bone to pop out at full extension. I m...
by metallicats33
Sat Jul 18, 2009 1:27 pm
Forum: RC10 Buggy Forum
Topic: CVD keeps coming out of out drive
Replies: 11
Views: 1506

Re: CVD keeps coming out of out drive

I'm almost 100% sure they are the MIP's Part #1007 , Product description says they are for all RC10's. It looks like the Right rear bone sits in just a bit more in than the left, enough not to pop out at full extension... maybe a shim or two might work on the left... I'll have to run to the hobby sh...
by metallicats33
Sat Jul 18, 2009 3:51 am
Forum: RC10 Buggy Forum
Topic: CVD keeps coming out of out drive
Replies: 11
Views: 1506

Re: CVD keeps coming out of out drive

Put a couple shims on the outer bone (inside the rear hub carrier) on the inner side towards the transmission. This will "pull" the CVD back in towards the outdrive cup. Hope this makes sense :). I was thinking about that but the wheel pin is already right up against the outer bearing... ...
by metallicats33
Sat Jul 18, 2009 12:59 am
Forum: RC10 Buggy Forum
Topic: CVD keeps coming out of out drive
Replies: 11
Views: 1506

CVD keeps coming out of out drive

I have an RC10 Graphite and I can't mount the bottom of the rear shock any where but all the way by the tire without the left CVD popping out of the left outdrive when the suspension goes full extension. This Is a problem for two reasons. 1. I get less travel for track use & 2, my Street tires r...
by metallicats33
Tue Jul 14, 2009 9:25 pm
Forum: RC10 Buggy Forum
Topic: Rc10 Graphite
Replies: 5
Views: 922

Rc10 Graphite

Hi, i've been a long time reader but this is my first post. I while back I got an RC10 Graphite from my friend's dad. After it sat in my garage for about a month I decided to bring it back to life. Before: http://www.rcnitrotalk.com/forum/picture.php?albumid=286&pictureid=1679 After: http://www....

Go to advanced search