RC10Talk - The Net's Largest Vintage R/C Community

I modified the upright : bearings are now inserted in the uprights and the screws are in the main arm. https://i.imgur.com/UkblcIC.jpeg The front train is now complete... https://i.imgur.com/pI1RJh0.jpeg Next activity is related to chassis plates... I will target a wheel base around 200mm in this fi...

While I love selling g10 and carbon parts, I think a project like that deserves something printed 8) Not really a tub chassis, but something with raised sides possibly. The Club Race Hero is a really cool design that you could borrow ideas from as well. The simple suspension system works great, the...

A quick test print to ensure it is printable, and the clamp works... (and yes, I added some cryptic message on some parts :-) ) https://i.imgur.com/1gW86Ey.jpeg https://i.imgur.com/0ntvrpX.jpeg I will just modify the master part of the front train in order to make it easier to position within the cl...

The AMS is currently on sale. I started with one on my X1C,and bought a second one quite quickly. You may not see the interest of the AMS at first, but once you have it you are going to change your mind. My own use cases are: multi colors - It's rare but I use this time to times finishing a roll and...

Sounds like good advice. Thanks. Extruder upgrades, AMS, etc, all in good time. I am retired so must watch my spending and delay some things until next month. That said, I can't print without filament so should I buy from Bambu or is there a better source? Also, can you please recommend a filament ...

I had this kit for some time under my desk awaiting I take the time to build it. I have some ideas of printed parts in mind, and to make them, I need first build the car... I also have next to it an Optima driver figure i'm likely to modify to put it in the cockpit of this buggy - Yes, I simply do n...

The Manx dune buggy chassis is supposed to be printed out of Nylon, but I used Silver PLA instead, with a 0.20mm layer height and using the Strength preset. https://i.imgur.com/TmzOhs7.jpg Even the ugly side isn't too bad, and was pretty easy to clean the supports off of, for once. https://i.imgur....

Sixth bag... Steering mechanism is in place... https://i.imgur.com/d251xXU.jpeg And then it's time to build the shocks... This gun metal is nice... And I remind about my shock gastket helper which makes it easier to push those shock gasket in place... https://i.imgur.com/xNHYhut.jpeg https://i.imgur...

To have clues about my wiring, I need to deal first with my battery support... For this I started to draw the chassis section (before checking, I also thought the lip for the Mid standard chassis would go along the edge of the chassis at the place where there is the battery and it is not the case). ...

Nice win, and nice cars...
Note for self : Maybe I should stop working on underdogs
Note for self bis : But I love underdogs and underrated cars

It was a tight fit, most likely based on the layer height settings, and the unfinished interior of the hub, the model looked great, the print could be better. Couldn't get that bearing back out, broke the part trying. Will print another. :D Yeah, I thought that might happen as I have not adjusted b...

By chance, are you also measuring the humidity in the buckets? Maybe knowing the humidity in storage isn't so important since you can always dry the filament when you're ready to use it? Thus, storing the filament in sealed containers with dehumidifiers reduces the time required to dry the filament...

I've did a few version for the ESC support as I'm not sure how it will finish at the end... https://i.imgur.com/xm3S69Y.jpeg https://i.imgur.com/6NH4fxO.jpeg The angled version will give easy access to the on/off button on my ESC (I made two version : one for cabon chassis and one for the standard m...

Last checks are now done... The files are available on makerworld : https://makerworld.com/en/models/748905 All versions are included with both versions of ESC supports. I made one plate per version (Hard pack 20mm, Hard pack 25mm, Shorty 25mm, Stick pack) and one plate with the two versions of ESC ...

I just received Ryo Inagaki's Artbook 2024


I feel like I participated to his book as he used two of my models as a basis for some of his work... And he made something very special for me on the very first page...
I love it