RC10Talk - The Net's Largest Vintage R/C Community

I've gotta find that 5108 to fill in my collection. Does anyone know what 5109 or 5111 are? (assuming they weren't skipped) The 5110 complete set has a ball bearing center gear and the deeper recess side gear as well, didn't know it was available separately though. 5100 Diff gear set 5101 left gear ...

^ RogueIV - Thanks. Cool looking brace you made. I have some carbon fiber 22-4 braces that I'm going to modify and try to make them work.

These are the Exotek 22-4 braces that I cut up to make work on the XX4. I still need to add some stops, and a few other small changes, but they already hold the batteries very secure. I removed the battery decals and wrapped them with faux carbon for looks and some protection.

I cut out and installed this Bittydesign wing. I also modified the stock wing mounts to accept wing washers and screws instead of body clips.

I also finished the rear swaybar links. Just waiting on my servo steering link to arrive.

Not really sure, those Andy's arms could be for the RC10.

Just a quick update: I had set this project aside because I ran into an issue where I couldn't set my differential or slipper right. Seemed no matter what I did either one slipped excessively or it was locked up. I chalked it up to the losi 13.5 Brushless motor being too hot and me needing to figure...

A few minutes into the run with the Onyx motor, it threw out a rear outer hinge pin. The snap-in clips that I used were worn and iffy, so not too shocked. Upgraded both sides with 5-link A-2007 pins and some used spacers. https://i.postimg.cc/FsTFhKG4/69-C1-C4-E5-C397-4370-AA04-F53957-EA4694.jpg The...

JC Racing wheels and Schumacher rubber has been installed. Still working on the stance, and a few other things to come. Comments always welcome.

Since I have been building my XX4 modern racer, I decided to try adding some period electronics to this one. I'm not going to solder anything in yet, but I think I like how it looks.

Looking good and not too ugly at all..you’ve seen my jrxt build, right? The only thing that looks off to me is the 2.5” pink front springs..too long unless you cut off 3 coils like the Jammin steering enhancement kit recommends.

Yeah that’s true! Ha.. Typically the .9 shocks use a 2” spring. 1.5” on .6, 2.5-2.75” on 1.2 rears. I’m almost done with my ProSE build..nice buggy buy the JrxPro is my favorite.

Not sure if there is already a place for this, if not, post current sales and coupons that will help fellow members. I’ll start with MCI Racing. They have a 20% discount for this weekend. I wasn’t aware they made repro RC10 plastic parts and tires.

Regards,

-limestang

https://mciracing.ca/

Minor update. I didn't like the double stack nose tubes holding the servo hostage so I'm moved them to the sides. It makes a little more servo linkage space too, although there was already enough for full steering throw.
.

This is an unboxing of the RC10 DS kit from Japan. This is the racer spec kit with teflon-coated shocks and full bearings. I think most Associated kits sold in Japan were all racing spec since parts and hop-ups were harder to come by. Mine didn't come with a body...is this normal or just missing? Th...

My big toys. It isn't hoarding if your stuff is cool... https://imgur.com/cnhMUYC.jpg 2020 Hyundai Veloster N, Daily driver and autocross weapon. https://imgur.com/nuHSf0R.jpg 1979 Alfa Romeo Alfetta GT, Small car - big body roll. https://imgur.com/HqoMVwN.jpg 1966 Honda CB77 Superhawk, Daily rider....