I'm interested in a set. Can they come in gold anodize? What other parts can you produce too? 6-Gear tranny case? front shock mount? Would be helpfully to have a complete list....
Sorry guys. I'll have to put this project on hold because i am unable to retrieve back the old Autocad due to PC crash!! As such, i'll not be able to machine any parts at this point of time till further notice. Thanks.
My collections:
Nikko Brat, Nikko Dictator II, Nikko Thunder Eagle, Kyosho Pure Ten Nitro, Associated RC10, Associated RC10T, Associated RC10 Graphite, Associated B4, Tamiya Tamtech 1/24 Porsche 962C, Tamiya Striker, Tamiya TRF 501X WCE.
I have no idea how much time you put into making that auto CAD design, but there are ways of retrieving data off a damaged hard drive (even easier if the hard drive itself isn't actually damaged). If you think it might be worth trying, pm me and I can give you some ideas to try and get the file(s) back. Good luck...
strangersinspace wrote:I have no idea how much time you put into making that auto CAD design, but there are ways of retrieving data off a damaged hard drive (even easier if the hard drive itself isn't actually damaged). If you think it might be worth trying, pm me and I can give you some ideas to try and get the file(s) back. Good luck...
Never thought of this Normally i'll just buy a new laptop once its down (3-4 years) as it's not worth repairing it. So I just dump the thing away.
My collections:
Nikko Brat, Nikko Dictator II, Nikko Thunder Eagle, Kyosho Pure Ten Nitro, Associated RC10, Associated RC10T, Associated RC10 Graphite, Associated B4, Tamiya Tamtech 1/24 Porsche 962C, Tamiya Striker, Tamiya TRF 501X WCE.
wyldbill wrote:hey guys their is youre awnser to the elusive rear arm mount. you could make a fortune just in rear arm mounts alone. you should make them in 1.5 degree and 0 degree.
Hi wyldbill, I won't be driving a Merc after selling these parts.... I fabricate them just for the fun of it and of coz, to restore my Gold Tub...
I do not think i'll be making the 0 degrees cos I do not have the plastic parts.
wyldbill is right , the rear arm mount you made is the part every rc10 rc10t rc10t2 owner needs.. you should make them in 1.5 degree and 0 degree. im sure someone would give or loan you 0 degree mounts to make them. if you did not want to do the 0 degree, id be very happy with the 1.5..in fact id just be glad to get any good rear arm mounts..
Parts are finally coming together for my Worlds chassis build. The bulk of the chassis will be aftermarket parts from Composite craft, RPM and Tecnacraft. I just put the finishing touchs on the wheels. Here is a peek.
Last post
Thanks for the compliments guys
So what is the history behind this car? What year worlds were these parts made for? This car is funadamentally different that the worlds car associated released.
Jim, I know you are looking down from above. Hard...
This Kyosho Ultima got a big make-over about 5 to 6 years back, and was turned into a 1/12 tourer.
The external 2-gear reduction was replaced by a scrap-built belt drive.
It reduces the complexity and friction, while adapting the gear ratio to the...
Last post
Same little porsche body, and a few more shared parts like arms and dogbones, but further a whole different car.
I just need to decide on the ESC and receiver and then it gets its own thread. These are just teasers with the added decals and new...
Just started going over it, pretty neat. Came from an ex-Jomac team driver. Features factory drilled wheels, graphite diff axle, lightweight spur gear, Novak Bantam Midget servos with factory black cases, 1200SC batteries (still good), Parma flat...
Last post
.........just something about them.
I don't exactly know what it is, must be the elegant simplicity. A bit of flexy plank with electrics and wheels, fine tuned to be a slot car with steering... and every manufacturer (and builder) put their own...
i picked this up off ebay last week. it had a team driver feel, and i just had to have it. and going by some other items that were being sold by the seller at the same time, it was possible imo. after the auction, i asked the seller about it, and he...
Last post
thanks guys. i'm happy with the way it turned out. :)
i guess i'll pick up a new protech body and a kimbrough wing and give it a quick paint job until a used painted original catches my eye. just so there's something on it.
at the flea market last year I bought a box and was told there was enough parts for three cars to be built. not true, but lots of parts. multiple graphite chassis, multiple shocks and front end arms, plus two aluminum rc10 chassis.
One chassis is...
Last post
hey, welcome to the board. :)
associated had some b stamp flourescent powder coated chassis' back in the day. green, pink, red, blue, and yellow. i think that's all of them.
I'm trying really hard to get this ready for the next vintage meet on the 14th of Feb, with a Technigold up it's bum it should give the RC10 & Losi brigade a run for their money...............if we go to the beach.
Anyway, I've been impatient so...