Vintage RC10T Build - conversion to BL
Vintage RC10T Build - conversion to BL
Hi everyone....i am new to this board and I am so glad i found it. A little background...currently my boys and i have 2 rc trucks...revo 3.3 (mine ) and a slash 4 x4 that i have upgraded beyond belief running 3s lipo. anyways, my boys love that slash....and to be honest so do i. when i first bought that revo i didnt know how good electric was these days..wich i would have bought the erevo instead.
anyways...on to the build. My 9 year old found my old RC10T that I was given to for xmas about 20 years ago. It currently has no motor and no controller...however my kid is obsessed with me putting a brushless in it. so after reading a lot of information on these forums...this is what i think i am going to do...and please add if i am forgetting something....
http://www.hobbypartz.com/car.html
http://www.hobbypartz.com/79p-gt2-blue.html
and all the parts needed for a b3t3 slipper clutch.
Attached are the pics...do you think that futaba servo will work with that receiver?
thanks for all your help everyone...its greatly appreciated.
also, if i wanted to upgraded to RPM parts and different shocks...etc...where is the best place to purchase?
anyways...on to the build. My 9 year old found my old RC10T that I was given to for xmas about 20 years ago. It currently has no motor and no controller...however my kid is obsessed with me putting a brushless in it. so after reading a lot of information on these forums...this is what i think i am going to do...and please add if i am forgetting something....
http://www.hobbypartz.com/car.html
http://www.hobbypartz.com/79p-gt2-blue.html
and all the parts needed for a b3t3 slipper clutch.
Attached are the pics...do you think that futaba servo will work with that receiver?
thanks for all your help everyone...its greatly appreciated.
also, if i wanted to upgraded to RPM parts and different shocks...etc...where is the best place to purchase?
- Attachments
-
- DSC01938.jpg (10.78 KiB) Viewed 4109 times
- DSC01938.jpg (10.78 KiB) Viewed 4109 times
-
- DSC01937.jpg (9.25 KiB) Viewed 4109 times
- DSC01937.jpg (9.25 KiB) Viewed 4109 times
-
- DSC01934.jpg (10.58 KiB) Viewed 4109 times
- DSC01934.jpg (10.58 KiB) Viewed 4109 times
- soniccj5
- Approved Member
- Posts: 1210
- Joined: Thu Jan 10, 2008 3:23 pm
- Location: Massachusetts
- Been thanked: 2 times
Re: Vintage RC10T Build - conversion to BL
Welcome to the forum.
You should have no problem using a futaba servo with that radio. I am using an old S148 with my TowerHobbies 2.4G radio.
Just a word of caution, this site is addictive and will cause you to spend large amounts of cash on RC-10s.
ED
You should have no problem using a futaba servo with that radio. I am using an old S148 with my TowerHobbies 2.4G radio.
Just a word of caution, this site is addictive and will cause you to spend large amounts of cash on RC-10s.
ED
-
- Approved Member
- Posts: 8921
- Joined: Tue Apr 08, 2008 2:44 pm
- Location: USA
- Been thanked: 8 times
Re: Vintage RC10T Build - conversion to BL
yeah, should be fine- the RPM parts are avail at Tower ( or a local hobbyshop ) and those shocks are just fine-
Re: Vintage RC10T Build - conversion to BL
I'd agree this forum is very addictive once you get going!
I've got the B4/T4 slipper assembly on my team car and RC10T readily available and perfect for brushless
I've got the B4/T4 slipper assembly on my team car and RC10T readily available and perfect for brushless
-
- Regular Member
- Posts: 5
- Joined: Tue Mar 22, 2011 7:42 pm
Re: Vintage RC10T Build - conversion to BL
will the b4/t4 slipper set up work on a stealth trans from the rc10t truck? Just got a castle creations 5700kv and the old slipper just slips even when tightened. whats all needed for the conversion if it can be converted?
- soniccj5
- Approved Member
- Posts: 1210
- Joined: Thu Jan 10, 2008 3:23 pm
- Location: Massachusetts
- Been thanked: 2 times
Re: Vintage RC10T Build - conversion to BL
teamplayer wrote:will the b4/t4 slipper set up work on a stealth trans from the rc10t truck? Just got a castle creations 5700kv and the old slipper just slips even when tightened. whats all needed for the conversion if it can be converted?
The top shaft in a B4 is interchangeable with the 2.25 stealth, but it will not work in the RPM transmission. I heard you can press the gear off, but I have not done that. Maybe someone else here can add more detail.
ED
-
- Regular Member
- Posts: 5
- Joined: Tue Mar 22, 2011 7:42 pm
Re: Vintage RC10T Build - conversion to BL
just bought the rpm trans conversion, but i still have the old stealth which is a 2.25 ratio. so with some luck, all might work and the slipper will hold up.
-
- Regular Member
- Posts: 5
- Joined: Tue Mar 22, 2011 7:42 pm
Re: Vintage RC10T Build - conversion to BL
my bad, had the wrong springs in the wrong places, it's been awhile since i torn into the old 10t. everythings holding up like a champ. thought it was fast with the sonic s that i had in it. with the castle creation 5700kv, insane, lots of fun.
Re: Vintage RC10T Build - conversion to BL
well here it is...havent ran it yet
will run this weekend
will run this weekend
Re: Vintage RC10T Build - conversion to BL
I have been looking at this combo too - did you go with the Sidewinder or the Mamba setup? Also, do you find the power controllable, enough torque? I have been debating between 4600 and 5700 for my RC10T restoration, and curious what you have found.teamplayer wrote: with the castle creation 5700kv, insane, lots of fun.
- CamplinP
- Approved Member
- Posts: 763
- Joined: Mon Aug 31, 2009 11:43 pm
- Location: Midwest Husker, USA
- Been thanked: 2 times
Re: Vintage RC10T Build - conversion to BL
My son has a 4600 in his T4 and it is plenty of power on dirt. I have the 5700 and I can hardly ever use it all. The two are a dead heat on our dirt track but he can run longer. The RC10T is also heavier so I would use the 4600 for the greater torque. I have heard the neu-castle motors have even better torque.
The Fox, Falcon, 9 RC10s black/gold/graph, Optima Mid SE EXT, Losi XXXT, B3, B4, 3 T4s, Evader BX, Evader ST, Buggy Champ '09, Sand Scorcher '10, RC10T, RC10DS
Re: Vintage RC10T Build - conversion to BL
i spoke with team associated and they stated that the old style stealth tranny is good about up to 4900kv
after running this weekend, thats about all the truck can handle. After 2 runs on a 2s the tires that you see above are now completely bald....haha
time for a good set of street and dirt tires.
This thing is really fun. It was nice to see it running again after about 20 years sitting in the garage.
after running this weekend, thats about all the truck can handle. After 2 runs on a 2s the tires that you see above are now completely bald....haha
time for a good set of street and dirt tires.
This thing is really fun. It was nice to see it running again after about 20 years sitting in the garage.
-
- Regular Member
- Posts: 5
- Joined: Tue Mar 22, 2011 7:42 pm
Re: Vintage RC10T Build - conversion to BL
i'm running the 5700kv sv2. Real happy with castle creations set up. On the other hand, the 5700kv is a little much. The slipper never stops slipping on pavment. It catches up on soft dirt. Most likely going with a b4/t4 trans or maybe a drill and a couple of roll pins. I know thats a no no, but i don't race on tracks, it's just a backyard basher. There is plenty of torque with the 2.65 conversion from RPM and a 87 spur and a 17 pinion. Over all, i'm happy with it, slipping slipper and all.
Create an account or sign in to join the discussion
You need to be a member in order to post a reply
Create an account
Not a member? register to join our community
Members can start their own topics & subscribe to topics
It’s free and only takes a minute
Sign in
-
- Similar Topics
- Replies
- Views
- Last post
-
- 79 Replies
- 11656 Views
-
Last post by DHood
-
- 44 Replies
- 5453 Views
-
Last post by romulus22
-
- 21 Replies
- 3558 Views
-
Last post by s10 warrior
-
- 26 Replies
- 3045 Views
-
Last post by slotcarrod
-
- 13 Replies
- 2283 Views
-
Last post by klavy69
-
- 3 Replies
- 1145 Views
-
Last post by daniels9424cs
-
- 12 Replies
- 4594 Views
-
Last post by jaro
-
- 7 Replies
- 1298 Views
-
Last post by unclemikey1978
Who is online
Users browsing this forum: No registered users and 7 guests