I picked these up last week to experiment with. They didn't really cost much at all and they work
I can program the Cyclone with my own custom parameters or use one of the 20 saved Novak sets to use as profile 4 on the Cyclone. Too bad I can't use with the C2 though, it has a different data link connector for the Novak Pit Wizzard.
I'd like to try Pit Wizzard also, but I would guess it would be quite pricey even if I found a working one
Photos and if anyone is curious to see the screen shots I'll post those also. Pretty cool Novak stuff
-Kevin
I have a Pit Wizard at home, which I picked up to use on the Novaks I have.... got it in the post, turned it on, saw that it worked, boxed it up, and it's sat on the shelf ever since!
Will get some pics tonight if you're interested...
Alex
Osiris is the key.
"The world looks so much better through beer goggles... except Farmer in his underwear" - Ken
Look out for Todd K. - he's a convicted serial killer!!!
RichieRich wrote:Wait, you have a computer with a serial port and diskette drive?
I'm a Mac guy in all honesty, but yes I do. I found it in the garbage and put XP on it I use it mainly for the old school Toyota Electronic Parts Catalog Software haha
-Kevin
Guys, need some advice. Took the YZ10 out today after building a pack and getting her all ready, hit a problem. Ive little to no braking!
Ive got the dial right up on the Cyclone, braking to 150 on my KO, and still theres hardly any there, its...
Last post
have you got your Schottky properly installed...?
big Cyclone fan, best ESC out there pre GT7 :D
usually if the brake FETs get fried they stay on/shorted
then the whole ESC warms up until it becomes toast
In my build process, I now have 2 different ESCs. One is a novak 410-m5 and the other is a Traxxus xl-5 which is the yellow one. I know that the Novak has been around for a while, and that the Traxxus has several programmable modes.
Is there a...
Last post
Todd- if I knew what I had, I would certainly be much better off. The best I can find is a marking on the motor that says ROAR 91.
should be a 27t stock motor.
I am pulling my hair out with this thing...It has a neutral and speed adjustment...Novak Solid state speed control is what it says on the case...I can not get the throttle to work at all...I have steering...The only time the motor will spin is when...
Hey guys, what can you tell me about this one from Novak?
In the pictures, look for a short bit of wire that is located at the receiver and switch output area. There are two wires, both red, soldered together. :shock:
I don't think that part was...
Last post
Out of the bag the 4 came with unterminated motor/battery wires. Deans plugs and a capacitor suggest it was used in an adults race car. The two small red wires are for the controllers BEC, connected together for up to 6 cell, unconnected for 7 and...
I have a pretty good collection of old Novak electronics and have seen just about everything out there but I have never seen or heard of this model before. It seems to be an early 1X chassis and the person I got it from said he purchased it in 1984....
Last post
Asso_man! thanks for posting the picture and a quick question, what material is that heat sink made out of aluminum? Also do you happen to have the dimensions of it? :D I did call Novak and they were very nice but they had no clue what this was....
I just purchased a Novak T4 esc that looks to be nos. Any pros and cons to this one?
Does it have reverse? Going in an 84 rc10. Thanks
Last post
Here's a link for the Novak T1 & T4 manual if you'd like. I just purchased a couple Novak ESC's for a couple of my older RC's. Was going to get a T1 and Duster, but got a Rooster and a Super Rooster due to the Roosters having reverse.
Looking at the Novak timeline it looks like a NESC-2 or a 1x from 1985 but there isn't a model name on it. I also have a NESC-1 in my box art rc10 that doesn't have a name on it either... what were the deal with these? Does anyone know definitely...
Last post
Good question. The 2 was better than the original 4 but the 2 was discontinued and I didn't want them to replace it with an inferior 4 - The T4 was brand new and I must not of known about it :roll: