Old RPM RC 10

General discussion, builds/restorations, etc...

Moderators: scr8p, klavy69

User avatar
Sharkman
Approved Member
Posts: 161
Joined: Fri May 19, 2006 11:53 pm
Location: 150 miles south of Widdys place

Old RPM RC 10

Post by Sharkman »

Fellas,I just about finished this one , still needs a few goodies but she's close. "A" chassis drilled for Stealth,RPM Rear bulkhead w/ a-arms,and up-rights,wide front arms,steering bell-cranks,and a set of ..... yup RPM white ball-cups.Lastly the only pair of T-craft buckles I own.I have a line on a new motorplate (un-hacked),and a single t-craft buckle for the center link.I have absolutely zero gold shocks anymore,so teamz will have to do for now,the 1/4" CVD's were just new and in stock. Hope you like it. 8) :wink:
Attachments
OLDRPMRC10 007.jpg
OLDRPMRC10 007.jpg (53.61 KiB) Viewed 1863 times
OLDRPMRC10 007.jpg
OLDRPMRC10 007.jpg (53.61 KiB) Viewed 1863 times
Dan

User avatar
Sharkman
Approved Member
Posts: 161
Joined: Fri May 19, 2006 11:53 pm
Location: 150 miles south of Widdys place

Post by Sharkman »

nudder one
Attachments
OLDRPMRC10 009.jpg
OLDRPMRC10 009.jpg (63.25 KiB) Viewed 1859 times
OLDRPMRC10 009.jpg
OLDRPMRC10 009.jpg (63.25 KiB) Viewed 1859 times
Dan

User avatar
Sharkman
Approved Member
Posts: 161
Joined: Fri May 19, 2006 11:53 pm
Location: 150 miles south of Widdys place

Post by Sharkman »

nudder two
Attachments
OLDRPMRC10 010.jpg
OLDRPMRC10 010.jpg (59.62 KiB) Viewed 1856 times
OLDRPMRC10 010.jpg
OLDRPMRC10 010.jpg (59.62 KiB) Viewed 1856 times
Dan

User avatar
Sharkman
Approved Member
Posts: 161
Joined: Fri May 19, 2006 11:53 pm
Location: 150 miles south of Widdys place

Post by Sharkman »

nudder three
Attachments
OLDRPMRC10 011.jpg
OLDRPMRC10 011.jpg (64.35 KiB) Viewed 1854 times
OLDRPMRC10 011.jpg
OLDRPMRC10 011.jpg (64.35 KiB) Viewed 1854 times
Dan

User avatar
Sharkman
Approved Member
Posts: 161
Joined: Fri May 19, 2006 11:53 pm
Location: 150 miles south of Widdys place

Post by Sharkman »

last one
Attachments
OLDRPMRC10 012.jpg
OLDRPMRC10 012.jpg (56.21 KiB) Viewed 1851 times
OLDRPMRC10 012.jpg
OLDRPMRC10 012.jpg (56.21 KiB) Viewed 1851 times
Dan

justinspeed79
Approved Member
Posts: 1679
Joined: Mon Aug 14, 2006 2:54 am
Location: Houston Texas
Has thanked: 2 times
Been thanked: 4 times

Post by justinspeed79 »

Nice! :D

User avatar
superfly
Approved Member
Posts: 125
Joined: Fri Aug 18, 2006 9:09 pm
Location: Toronto ON Canada
Been thanked: 1 time

Post by superfly »

AHHHHH that white plastic!!! SO BRIGHT!!!! SO NICE!!! I"M BLINDED!!!! :lol: Nice car boss

User avatar
scr8p
Administrator
Posts: 16524
Joined: Wed Feb 08, 2006 2:46 am
Location: Northampton, PA
Has thanked: 28 times
Been thanked: 957 times

Post by scr8p »

looking good dan.

if that line on a tie rod for your bellcrank falls through, i got ya covered. :wink:
Attachments
IMG_1414.JPG
IMG_1414.JPG (161.72 KiB) Viewed 1786 times
IMG_1414.JPG
IMG_1414.JPG (161.72 KiB) Viewed 1786 times

User avatar
shodog
Approved Member
Posts: 3816
Joined: Thu Oct 05, 2006 7:09 pm
Location: Washington
Has thanked: 3 times
Been thanked: 86 times

Post by shodog »

looks like someone has a secret stash of tecnacraft turnbuckles

User avatar
scr8p
Administrator
Posts: 16524
Joined: Wed Feb 08, 2006 2:46 am
Location: Northampton, PA
Has thanked: 28 times
Been thanked: 957 times

Post by scr8p »

shodog wrote:looks like someone has a secret stash of tecnacraft turnbuckles
nope, just that one. :lol:

Ron Jeremy
Approved Member
Posts: 263
Joined: Mon Jan 29, 2007 7:27 am
Been thanked: 2 times

Post by Ron Jeremy »

I didn't know RPM made bellcranks. Those look pretty nice.

User avatar
carloco8
Super Member
Posts: 628
Joined: Sun Jun 04, 2006 6:02 pm
Location: SoCal
Has thanked: 10 times
Been thanked: 27 times

Post by carloco8 »

Ron Jeremy wrote:I didn't know RPM made bellcranks. Those look pretty nice.
Yup, bearing and non-bearing. White plastic had bearings and black plastic had no bearings, right guys?

User avatar
Sharkman
Approved Member
Posts: 161
Joined: Fri May 19, 2006 11:53 pm
Location: 150 miles south of Widdys place

Post by Sharkman »

Thanks all for the flowers. Carlo' I remember seeing white peices somewhere,not sure of the plastic/bearing difference though.I'd be interested in a white set if this is the case.I'd trade the black with a bit of coin :D

Jason,.Thanks for lookin out.I'll get with you asap if the line "breaks" 8) TTYS!!
Dan

User avatar
carloco8
Super Member
Posts: 628
Joined: Sun Jun 04, 2006 6:02 pm
Location: SoCal
Has thanked: 10 times
Been thanked: 27 times

Post by carloco8 »

Sorry Sharkman, I don't have either type, lol. I'm just basing my reference off of seeing them on ebay (both types) and the bearing types on scr8p's and hoopty's rpm 10s.

Btw, nice car! I noticed that you have one of those neoprene gaskets on it too!

  • Similar Topics
    Replies
    Views
    Last post
  • RC10 RPM Bulkhead/ 10T RPM Bulkhead
    by Caine » » in Temple's RC10 Tech Forum
    2 Replies
    570 Views
    Last post by Caine
  • RPM 2.65
    by TViz » » in Temple's RC10 Tech Forum
    3 Replies
    361 Views
    Last post by TViz
  • RPM-X2
    by mrlexan » » in Losi Forum
    16 Replies
    1703 Views
    Last post by wyldbill
  • rpm
    by dave fugate » » in Losi Forum
    1 Replies
    445 Views
    Last post by aconsola
  • RPM
    by rc10johnny » » in RC10 Truck Forum
    3 Replies
    865 Views
    Last post by slow_jun
  • RPM conversion?
    by RC10th » » in RC10 Buggy Forum
    2 Replies
    833 Views
    Last post by RC10th
  • 2.25 Stealth or 2.65 RPM?
    by LTO_Dave » » in RC10 Buggy Re-Release Forum
    8 Replies
    1091 Views
    Last post by RC10th
  • white rpm T
    by treehugger » » in RC10 Truck Forum
    11 Replies
    1309 Views
    Last post by burnsmonkey

Return to “RC10 Buggy Forum”

Who is online

Users browsing this forum: No User AvatarBing [Bot], No User AvatarCommonCrawl [Bot], User avatarduckhead, No User AvatarFacebook [Bot], User avatarjuicedcoupe and 2 guests