Scr8p's Worlds Re-re #2 / Modern Satoshi Maezumi Replica / 2017 Vonats Build
- GoMachV
- Approved Member
- Posts: 11709
- Joined: Mon Apr 30, 2012 2:31 am
- Location: Twin Falls, ID
- Has thanked: 884 times
- Been thanked: 2891 times
Re: Scr8p's Worlds Re-re #2 / 2017 Vonats Build
I only use the washer because the axle nut won't thread on fully.
It's time to stand up to the bully. Support the companies that support the industry, not the ones that tear it down. Say no to Traxxas
Factory Works website
Factory Works website
- scr8p
- Administrator
- Posts: 16625
- Joined: Wed Feb 08, 2006 2:46 am
- Location: Northampton, PA
- Has thanked: 29 times
- Been thanked: 1059 times
Re: Scr8p's Worlds Re-re #2 / 2017 Vonats Build
You definitely need thick washers to use them on an rc10.
-
- Approved Member
- Posts: 59
- Joined: Sun Dec 11, 2016 4:01 am
- Location: Metro Detroit, MI
Re: Scr8p's Worlds Re-re #2 / 2017 Vonats Build
I have notice the same thing on a couple pairs of hubs lately...is there a better source for hubs? I have some SC10 parts, but this moves the axle out further.scr8p wrote: ↑Wed Jan 04, 2017 5:15 pm I picked up a pair of black rear hubs for this to mimic the original car and not have to dye anything. So I'm throwing the rear suspension together and what do you know..... The black hubs are all of a sudden just as bad as the hub's from the classic kit. The bearings just fall in and wiggle all around. So I ended up dying the ones from the kit anyway.
Very clean work BTW!
RC10 WC re-re / SC10.2 / RC10 CE / 2x RC10GT-E / Futaba FX10
- scr8p
- Administrator
- Posts: 16625
- Joined: Wed Feb 08, 2006 2:46 am
- Location: Northampton, PA
- Has thanked: 29 times
- Been thanked: 1059 times
Re: Scr8p's Worlds Re-re #2 / 2017 Vonats Build
The white ones from the kit are fine. Just have to dye them if you want black.
Only other option is finding old school original ones.
Only other option is finding old school original ones.
- scr8p
- Administrator
- Posts: 16625
- Joined: Wed Feb 08, 2006 2:46 am
- Location: Northampton, PA
- Has thanked: 29 times
- Been thanked: 1059 times
Re: Scr8p's Worlds Re-re #2 / 2017 Vonats Build
I found a pair of hexes from Team Losi that would work for me on this build. The raised spot on the back need to be milled off so it goes flat against the wheel spacer. But other than that, they're perfect.
- scr8p
- Administrator
- Posts: 16625
- Joined: Wed Feb 08, 2006 2:46 am
- Location: Northampton, PA
- Has thanked: 29 times
- Been thanked: 1059 times
- GoMachV
- Approved Member
- Posts: 11709
- Joined: Mon Apr 30, 2012 2:31 am
- Location: Twin Falls, ID
- Has thanked: 884 times
- Been thanked: 2891 times
Re: Scr8p's Worlds Re-re #2 / 2017 Vonats Build
Oooh nice
It's time to stand up to the bully. Support the companies that support the industry, not the ones that tear it down. Say no to Traxxas
Factory Works website
Factory Works website
- RC10th
- Approved Member
- Posts: 4511
- Joined: Sat Feb 16, 2013 2:51 pm
- Location: Australia
- Has thanked: 45 times
- Been thanked: 1233 times
Re: Scr8p's Worlds Re-re #2 / 2017 Vonats Build
Looking pretty good !
I was old school - when old school wasn't cool !
- Lavigna
- Approved Member
- Posts: 1334
- Joined: Wed Aug 05, 2015 8:24 am
- Location: Petaluma, CA
- Has thanked: 898 times
- Been thanked: 1098 times
Re: Scr8p's Worlds Re-re #2 / 2017 Vonats Build
Looking great. love the attention to detail. Right up my alley. In for the end result.
My Photo Gallery --->https://www.rc10talk.com/viewtopic.php?f=77&t=38934
- slotcarrod
- Approved Member
- Posts: 4415
- Joined: Wed Nov 26, 2008 3:57 am
- Location: Calgary Alberta Canada
- Has thanked: 1 time
- Been thanked: 43 times
Re: Scr8p's Worlds Re-re #2 / 2017 Vonats Build
You gonna use chassis tape right? It would be a shame to scratch it!
Rod Littau
Slotcarrod's Rumpus Room: http://www.rc10talk.com/viewtopic.php?f=77&t=16113
25 Years of the RC10: http://www.rc10talk.com/viewtopic.php?f=35&t=13059
Slotcarrod's Rumpus Room: http://www.rc10talk.com/viewtopic.php?f=77&t=16113
25 Years of the RC10: http://www.rc10talk.com/viewtopic.php?f=35&t=13059
- scr8p
- Administrator
- Posts: 16625
- Joined: Wed Feb 08, 2006 2:46 am
- Location: Northampton, PA
- Has thanked: 29 times
- Been thanked: 1059 times
Re: Scr8p's Worlds Re-re #2 / 2017 Vonats Build
Yeah, I'm gonna put something on it. The B1.5 I ran at the '15 race got hammered and I don't want this one to have the same fate.slotcarrod wrote: ↑Thu Feb 09, 2017 6:19 am You gonna use chassis tape right? It would be a shame to scratch it!
ROH73 talked about getting his vacuum forming machine fired up more this year, so maybe I'll see if he could knock out an under tray for me. I'd rather do that than chassis tape.
- klavy69
- Moderator
- Posts: 5191
- Joined: Thu May 29, 2008 8:11 pm
- Location: Fulton, IL (Land of one stop light but we DO have a windmill!)
- Has thanked: 599 times
- Been thanked: 285 times
Re: Scr8p's Worlds Re-re #2 / 2017 Vonats Build
if he doesn't get around to it get ahold of me. I have some of the last ones he made.
Todd
Peace and professionlism.....Kabunga signing off!!!
- ROH73
- Approved Member
- Posts: 623
- Joined: Sun Feb 10, 2008 5:07 am
- Location: State College, PA
- Has thanked: 2 times
- Been thanked: 19 times
Re: Scr8p's Worlds Re-re #2 / 2017 Vonats Build
I'll get to it...and that gear cover. I promise
I really like that blue; great job!
I really like that blue; great job!
-
- Similar Topics
- Replies
- Views
- Last post
-
- 52 Replies
- 9554 Views
-
Last post by scr8p
-
- 55 Replies
- 10901 Views
-
Last post by scr8p
-
- 34 Replies
- 5238 Views
-
Last post by scr8p
-
- 33 Replies
- 6797 Views
-
Last post by Worldsman
-
- 0 Replies
- 770 Views
-
Last post by phoenix
-
- 8 Replies
- 2111 Views
-
Last post by Charlie don't surf
-
- 20 Replies
- 6186 Views
-
Last post by RC10th
-
- 32 Replies
- 4666 Views
-
Last post by vintagercaddict
Who is online
Users browsing this forum: CommonCrawl [Bot], Google Adsense [Bot] and 5 guests