RC10Talk - The Net's Largest Vintage R/C Community

WOW - I like it!!
Does anyone have one of these yet?

Hello!
Any difference between MIP RC10 4x4and Ten4?

Is Ten4 still available?

What is the rear transmission on the Ten4? The AE stock 6 gears transmission?

Thanks 🙏

Admittedly going to be a long while until I get into this one, still working out exactly what I want to do with it. C5A92806-54BD-485C-B3E3-C0C7D9E0EE3A.jpeg 0BA8FDC2-4871-4BA4-BAF1-B6DA66345508.jpeg DB2881C1-9CC4-4534-8453-CF8FA7371D6D.jpeg...

Anyone have the dimensions for the cut of the chassis? Like how much of the side to leave? Tips for cutting?

was going to tear this thing apart and convert to a dirt oval car but longer i looked at it the more i just dont know...i know for sure all electronics have been upgraded recently inc. motor thats about it on that....

but i noticed some oddities...

I'm in the middle of building a composite craft/RPM worlds buggy and trying to figure out the best body to use on it. It looks like the ultramolded chassi preference is a losi xx body, but I haven't seen if there is something recommended for the...

:? well maybe. i don't have much info on this chassis yet. maybe an andy's prototype :roll: the chassis is drilled for the 6 gear trans and traxxas trx10 (bullit) front bulkhead.

Bottom RC10 Extra Holes.jpg

Please look closely at the bottom of this RC10. The additional servo and battery mount holes appear to be factory drilled. I say that because the inside of the holes appear to be anodized. Yes some are not countersunk...

I have a chance to buy what the owner claims is a never run, Edinger RC10 with box and everything with it, motor and electronics still in bags. Only the body had been painted. His pictures support this claim, but wondering if worth the 600 dollar...

I've got a couple of Comical RC10 buggies to build. I'm starting out with the shorty Masami style build.
.
PXL_20230905_143031186~2.jpg
.
A little kickoff to the assembly work.
.
PXL_20230905_160007395~2.jpg
.
PXL_20230905_171439623~3.jpg

I had always assumed AE just copied Composite Craft's bellcrank design and modified the post to be on top instead of the bottom for the 6037 Worlds Car. However I never knew it was primarily due to Kinwald using the CC bellcranks at the 1993 IFMAR...

After their domination at the 85 race, what was the race story for Team Associated losing in 1987?
Do we have closeup pictures of what Team Associated raced with? I see that the MIP RC10 placed 4th below...

1987 IFMAR 1:10 Electric Off-Road World...

Hello, could someone tell me if the RC10 Graphite came with the short or long front arms?? I've looked at pictures and it confused me even more. The reason i aske is that i recently acquired a graphite chassis and would like to piece together my own...

Sorry, but I am having trouble searching and trying to find what is needed to upgrade my Early (80’s) RC-10 buggy.

Many upgrades back in the times, sway bars motor etc but never did anything with the wheels and tires.

I would like to know ways to...

Hey guys, posting up some pics of a build I have been putting together for a while now. Many of the vets here have helped me source things (thanks to you all). Here are some pics, hope you enjoy.

This was the first RC10GX (NIB) I ever saw auctioned off in Japan. It is the earliest version of the RC10-GX. The main difference between this and the US spec is the inclusion of Yokomo aluminum wheel adaptors for Yokomo 2.15 inch rear wheels, extra...

Will this Robinson Racing spur work on a six gear? The diff ball holes are different to the #6634 spur. SUPER_SPUR.png

Hi there ....
I am a New member from germany, building a New RC10 with JC suspension parts.
Got a New tub, stealth is like New.
Run the donation car at the last Euro Masters in GB together with Mr Drescher in the A Main ....
Looking forward to a...

Hi everyone,

I present to you my freshly built Team Associated RC10FX. This model was released in Japan only and is essentially an RC10 Championship Edition with a few extra parts not included with the American (and everywhere else except Japan)...

It's been a while since I built an RC10. So I figured it was finally time to open a NIP Lightz oval conversion I've had for many years.
There's nothing fancy on this one and I built it as more of a gearbox club racer.

- Lightz oval conversion...

I will come back and update this thread in a few weeks. But for now, I just want to show it off for guys that donated parts to the project. This is where your stuff went. If you know the back story, please keep it to yourself for now. I'll explain...

In looking for a couple of sets of Hazard wheels, all I can find available anywhere (including manufacturer's site) is yellow, and a few sites I have been to are listing the white and black versions as Discontinued. Anyone know for sure if they are...

I picked this car up a couple years ago now exactly as you see it. Well actually it’s probably a little dirtier now from just sitting on a shelf in the garage.
Since there’s not too many AE parts on this one I figured we could all have a little fun...

Hi All, just after a bit of advise,

is it possible to use other shock shafts and seals in associated hard anodised shocks,

am I correct in assuming that the diameter of the imperial shock shaft will be different to a metric shock shaft and then...

Intro & Background
Hello everyone - I'm new here (as you can probably tell) so forgive me if I commit any infractions to unspoken rules. I read the forum rules and I think I've got everything down correctly.

The background to this is that my dad...

Is transmission and chassis same on rc10 ds with exception of nose plate?

Hi All,

I got a set of rims like what Jay Halsey used on his 1985 IFMAR winning buggy. What bearings or bearing inserts did he use? Does anyone have a link to where I can get what I will need?

Also, does anyone have a lead on the right tires for...

Where to begin... After acquiring parts for different projects and changing directions midway this buggy finally took form. After seeing scraps b1.5 build awhile ago i always wanted to build something similar if i ever came across a t2 for a doner....

Hi all.

Has anyone managed to paint associated shocks with good results to refresh them or change colors ?

In the process of putting together a RC10 stealth 91 replica I have to get many parts from the rc10T.
I found some in my area but the...

Really want to do a mid motor from all new available
Parts
Any suggestions for parts suppliers

Thanks in advance

Sassy Chassis ad's were plentiful in RCCA starting in 1990. I figured that I would try to source a standard RC10 chassis as the base for an all new hopped up build. There are only a couple of AE factory pieces such as the tranny brace, ball cups,...

I finally have my holiest of grails, thanks to Asa. :wink:

And to think, I nearly parted this car out and sold it out of frustration of not being able to find my Aero-foil. I'm still not sure if I'm 100% settled on the Worlds chassis, or if I...

Is there a gear diff that fits in stealth transmission

Do you notice any handling differences between the RC10 graphite team car and the RC10 team car with tub chassis (both fitted with white nylon parts throughout)?
I haven't driven either yet. Been a while...greetings all :)

Hi All,

What aftermarket tires (front and rear) will fit the original stock rims? I believe the Kyosho Sand Super tires will but want to confirm and see if any others fit. Thanks a bunch...

Years ago I got my built in 1989 JRX2 off ebay. All it said was new built in 1989 never ran, with like two blurry dark pics of a car and box. The price I paid was either a steal or gamble. When it showed up new as could be with original sales...

Hello,

I'm pretty new to the forum, at least this is my first thread.

I recently scored this RC10, that I believe is an Edinger from the mold of the gear cover and the stamp on the chassis.
It's in a great shape, besides a few scratches on the...

Hi All,
I searched the forum first so if I missed it, please post the link...

I am rebuilding an original RC10 and building a B6 (going for a retro look). I would like to get both anodized in the original Associated gold. Where might I be able to...

Just got inspired by some threads on the Tekin conversion to post an old build. As per usual I had collected parts for a long time and wanted to build a mid motor conversion for vintage racing on modern carpet tracks. In 2014 I was ready to assemble...

My original body has seen better days and I'd like to get either a new OEM body or maybe an aftermarket that fits my 1989 RC10 Graphite. Anyone know what the name/part # is for the original body & wing that came with it? I keep reading about the...

Hey guys! Years ago, I built an RC10 with the A&L C2 chassis set. I originally put a ProTech II on it with the rear of the body going over the top of the shock tower. I thought the body looked too high so I trimmed the back off to lower the body. It...

Huge shoutout to Larry Doe for all of this help in making this replica as accurate as possible. Still need to add the IFMAR tech decals, number plate and chassis protector but she's 99% of the way there.

Hey guys. I've been updating some of my RC10s. Also, I moved to a new, bigger house back in early 2021. This means that I've been able to organize all of my cars and parts. I've found that I had lots of stuff squirreled away including plenty of RC10...

Picked this one up today. This is my brother's original RC10 from the 80's. It started life as an original A stamped gold pan, but he modified it with the long arms and longer shocks in the front along with new arms in the rear. After sitting for...

Good day, folks...another question to pose, where I couldn't find an answer previously posted.

I'm (mostly) rebuilding my A-stamp, with the early gold shocks...the era when they only had a hard nylon washer to seal the caps to the bodies. I've got...