Got this in a lot a while back. I'm trying to find the specs on it, but can't find it anywhere. :? My guess is Hong Kong which is fine, but makes it hard to track down. Sorry for the blur. I should have changed a setting on the camera. Any help?...
Anyone used these? They have a 7.4v 3200 hardcase at Stormer for $59.99. I'm looking for one more less expensive Lipo. They have a couple of Maxamps 3000mah for $59.95 too. Or if anyone has any other suggestions I'm open to opinions.
Last post
Just wanted to update the lipo talk a little bit, I've been running the Yeah Racing packs for a little while now and they are great! The 3200's are now ROAR approved, so that right there should make people stop and take notice. not to mention you...
My brain is turning but I'm not getting nowhere quick
I'm sure there is a chart somewhere out there to tell us what the equivalent brushless motor turns are to brushed motor turns. Maybe this can be a quick and painless fix for me and possibly...
I just recently won a rolling RTR B4 for $51.oo USD off of ebay, :mrgreen: and I have been thinking about putting a brushless combo system in it. I don't think I will be racing it, although I have been asked by the local RC community if I wanted to....
Last post
I loved brushed motors. Brushless just doesn't have the character of nice modified wind.
or the smell... :wink:
i got a bunch of novak brushless stuff (the old ss5800, couple gtbs with a 17.5 and 6.5) and one speed passion gtb with the 17.5 spec...
ok you mamba max guys i got a used system. when everything is hooked up and i go to calibrate it to the radio all i get is the tones and a flashing red light :( and no steering. anybody got any ideas :?:
Last post
got it fixed up and runnin. tore it apart and found 2 reciever wires departed from the board. :lol:
It came in my recent Treasure Boxes. When I picked it up, water was actually DRIPPING from it. It was FULL. We immediately took the covers off, anddried it out as best we could with a towel, and its been air drying for 3 more days. He said it was...
Last post
ITS ALIIIIVE, ITS ALIVE.....MWAHAHAHAHA, ITS ALIIIIIIIVE!!!!!!!!!
I only tested it in my 10T (FIRST time to drive it also, WOOHOO!!), with a Rx, and S148 Servo, that both also came from my recent Treasure find. They also worked fine.
i bought a 3000mah nimh pack from then and charged it at 2 amps its first and second charge and 4 amps from then one and the battery was pretty hot after each charge. thought it was normal. now after about a month the pack doesnt have the punch it...
Last post
i will agree with lostwages....without proper care, NIMH batteries will take a dump on ya. I had $80 packs that I cared for like they were my children that took a crap on me after 10-20 cycles.
I just updated my charger with one capable of charging LIPO's and charging Ni-Mh's at up to 5 amps.
I've been charging all my Ni-Mh's at 5 amps-they include GP4300,GP3800 and an IB3800.
Since I've started charging these batteries,both the GP's have...
Last post
if ur bashin around and not racing, you may want to look into the a123 nano's from maxamps 3s config 9.9 is pretty sweet and ya can abuse those things to no end and they charge in about 15 minutes
Hi there I have just acquired an mtroniks pro digiMAX brushed ESC, the only problem is that I have no info or instructions. I have tried the mtroniks website with no luck. I was wondering if any body out there had any info of any kind as it would be...
Last post
Thanks very much mate, as soon as a get the thing fitted into a buggy i shall give that a try. :D
Alright, I am in the process of returning my YZ10 to life and I would love to run Lipo's as I am just going to use the car to run around (not race). I have ancient electronics (Novak T5) and old old Twister stock motor. I am looking at the Lipo...
Last post
You MUST use a lipo charger, in lipo (CC/CV) mode. Or else everything goes up in flames. Cannot allow an individual cell to go above 4.2 volts (technically 4.25v if you like standing right on the edge of the cliff, but your meter better be...
Keep seeing the loose cell lots on ebay for attractive (read as cheap) prices. I've read a couple other places that they are junk, but no one mentions their setups? I was wondering if anyone here has used them for any sort of bashing or racing? most...
Last post
i've run the 4200 for several month they where good but like evrery thing some packs where beter then others so i sold them and convert to li-po best move i done in my almost 20 years of rc so much power in those 5000mah
I got this ESC with the JRX Pro I traded some stufffor.
I dismissed it,at first-I didn't even bother to test it.
Got around to testing it today,though and it works very,very well!
Trouble is-I don't know the motor limit,or what the adjustment pots...
iam gonna start racing on an indoor carpet track and running a cobalt 27t pro so ill prolly need atleast 2 batterys what would you guys recommended for long life and good run time
Last post
all fixed. i was gonna clean it up this morning, but i had to rub it in first. :P :lol:
I have several old Tower Hobbies Timed Chargers. The fuses have blown in all of them. They call for a .75 amp fuse, but I could only find .50, and 1.0 amps fuses when I went to Town. Which should I use, or should I just wait until I get what they...
Last post
We should both have our stuff by Monday then. Thanks.
On the fuses, Radio Shack is where I found these. They looked at me like I ask for plutonium, when I ask about the .5 fuses. Have I mentioned before (I KNOW I have, lol) that I live the...
I'm running out of ESCs for my cars. I only have a super rooster left which is overkill for what I need.
What would be a good ESC WITH REVERSE for cheap. Something for stock and middle range modified motors . I need something cheap so I can buy...
Last post
Noticed these Dynamite Tazers while looking through a new catalog. No idea if they are any good, but fairly cheap and have a 1 year warranty I believe.
It can run 2s, but not 3s. That's just under 100,000 RPMs. You may have to take your car to the salt flats in Utah to have enough room for that kinda speed. I can't wait to destroy a car with it! :D
Last post
We've had good luck with the Novak Light series motors we've tried. Plenty of top end, but a little more subdued acceleration, a little easier to use off road. Kinda like a double or triple wind brushed compared to the regular brushless, which is...
I have a Castle Mamba Max with a 5700kv motor.I love it,it is everything I could ever ask for in a brushless setup. :mrgreen: :twisted:
I've been running NI-MH batteries and lately,a few of them died on me.
I just bought a really good LI-PO ready...
Last post
Orion, TrakPower, and SMC are all considered top notch stuff. They are all matched, hold balance quite well, of course a balance charger is still wise in my opinion. And they are known to actually make their claimed numbers, very good voltage under...
Okie, I have a 17.5 motor and a 5.5 motor, both Novak Brushless, the guys at RCHR are running 8.5 and 10.5, I know if I use the 5.5 it'll be too much to handle on the track on a 2wd T4.
Can the 5.5 be geared down? Enough to compare to atleast an...
Last post
You dont say if you are running LiPo or NiMh cells but...
There is a local guy over here in OZ that regularly runs a 3.5 or 4.5 motor in his B4, but he also only uses 4 or 5 cells depending on the track conditions..
I'd like to have the option to go lipo as that seems to be the better technology. I currently have 2 tekin 112 series chargers, and one CE turbo35 Gfx. (of course I have a few boat anchors/old school chargers too)
The GFX is a blue screen version...
Last post
but as you know it's a huge box, + power supply too.
I've seen many people open the case and take the Radio Shack 15 amp power supply (also removed from its case) and mount it inside...really slick deal. I've thought about picking one up myself...
I need some help here guys. I have a truck that keeps eating motors and ESC's its getting costly to fix this thing. Its an XTM electric x-cellerator (my sons truck) it has always eaten motors and escs but since the motors were junk I figured they...
Last post
go brushless and you won't need to replace any brushes
If I wanted to tune down the speed of a motor, can I use the Throttle EPA adjustment to do it??
Or would it have to be the EXP adjustment??
I want to use my 5.5 on the T4, but gearing it down can hurt the ESC, and running it as is, it's too much...
Last post
I ran the truck this weekend with the 5.5 and turned the EPA down to 70% and she was a beast out there, now it's on to acquiring a Lipo pack and I'll have my race truck set up properly.
1> I recently purchased a Lipo charger that does NOT have a balancer? Are balancers really necessary? Was it a mistake to buy a charger without a balancer?
2> Have you heard of the MYSTERY balance Chargers being sold...
Last post
In my experience (and I've had at least 15 lipo packs now). Good quality 2S packs rarely go out of balance, cheaper ones can drift and old packs even more so. Anything above 2S I would never charge without balancing.
This is in my Sons T3, so I havent paid it much attention, but I thought it has been doing better than it is. Hes gotten a little better, so I decided to check out the Truck and maybe put a 27t Stock Motor in for him. Hes been running a AE 20Power...
Last post
i don't know what kind of radio it is, or you tried, but make sure all of the atv/epa adjustments are set at max. set all of the trims at 0. make sure you put a motor in the car that you know for sure works fine. then, reset the esc. if it still...
Ive had 2 969s for a while now, and my Batts have seemed to steadily go down hill. I recently sent 1 in to MRC for a check up and New Buttons (they seem to be notorious for getting hard to use), but it hasnt done any good at all. I can certainly...
Last post
Hmm, I thought the ICE Chargers DID do 2 Batts at once (no idea where I got that idea). Nevertheless, I will comtinue to reasearch/SHOP.
I'm getting my buggy ready for the vintage nationals. During my test runs on the street behind my building, I've been getting horrible reception. I don't think the car will go past 40 feet until it just goes dead. I think it gets decent reception on...
Last post
open the novak rx and blow any dirt out of it, I lived in Tucson, not quite brooklyn I know. But if any sand or dirt got into my mercury or xxl they wouldn't work. I run a 8 year old xxl in my gt and it never glitches. I love spectrum, it makes...
I ran my truck this Saturday at the VONATs track, and at certain parts of the track it would glitch like crazy, and it would be fine at the other end of the track, I'm running an Airtronics M8 with the Synth. module and switch receiver. I'm using...
Last post
It's crazy though, because I'm running the same set up on the Losi and it's nice and glitchy free, I think my problem is running the ESC wire that connect to the Receiver underneath the battery tray, close to the Metal chassis, didn't think of that,...
forgive my dumbness lol, i know little about lipos really, seems like 5k mah for under 100 would be good, but is there like a drawback to this pack as opposed to a pack for $169?
Last post
at my local track, EVERYONE and their brother is running the LRP sphere comp ESC and novak motors, they say its the best combo out there. The novak gtb's they find slow to respond they claim, and the LRP motors they say arent the greatest. thats why...
Does anyone have a good method for mounting a house transponder in a jrx-2 that doesn't involve drilling a hole in the body? there is not much room under the lid with all the electronics in place.
On my jrx-T I put a hole in the right side dirt...
Last post
Personal transponders (low profile and red in colour generally) do have the three tags - so that is what is confusing you.
Most loaner transponders from raceways and clubs look like the dummy ones shown on the losi above (albeit in red plastic)....
I was looking for some hop ups for the 10t, and found the rpm 2.65 kit on towerhobbies, it says that it'll give the truck better acceleration, I was wondering, is it worth getting? doest it make a noticeable difference in acceleration??.
I'll...
Last post
:D Ok got it all figured out, I bought the cutting fluid and a new blade, and voila, shiny new Comms!!!! yay!!! :D
Now I feel a little more confident about running the brushed motor. 8)
I am trying to repair my old Futabe MC112B ESC speed controller and need to find a cross reference parts number for the transistor. Does anyone know of a good place?
Transistor S110 I 76
Thanks,
ED
Last post
On the same topic, has anyone found a suitable replacement schottky diode that doesn't cost $2 each?
i want to impregnate my new runner with a complete fresh rack of electrics. i'm definately going brushless and i'm leaning
towards a novak system, although i'm not sure which are the best (ss, gtb ... ?). i'm a complete green gill really and the...
Last post
thanks everyone, its made everything a lot clearer!
OK, decided to actually finish one of my projects( :lol: ) but need to pick up some stuff and think I want to go lipo battery powered with it. Its a traxxas velineon bl setup on this ride(I know, I know...was a good deal at the time) and don't know...
Last post
The higher the C rating the more amps the cell will put out. 1 C is 10 times the ah of the cell.
Just to clarify as I'm not sure this wasn't a typo. I was under the impression that 1C is 1 times the amp hour rating of the cell, this is important...
I got my new motor in today, its a trinity 17t speed gems, brand new tekin rebel 2 esc. gp3300 6 cell, 12t pinion and 54t spur, no matter what i do this frekin car wants to burn up my motors, im about 5 inches from shelving it and calling it a loss....
Last post
Sometimes, it's hard to figure out the problem with just a picture. The 6 gear transmission can be a real pain sometimes. There's got to be some binding somewhere.
Does your car have dog bones...or universals? Are the wheels spaced out correctly?...
So I just purchased my first DC only NiCD and NiMH peak charger but now I need to get a power supply for it. Can anyone suggest a good one? I really don't want to spend a lot of $$$ on it because my wife already has her sniper rifle sighted in my my...
Last post
Thanks for the suggestions wyldbill... I appreciate it. Maybe I'll take a ride to Radio Shack tomorrow and see what they have in stock.
Hey guys, I have a couple of Reedy Ultra series motors that need some new brushes. Does anyone have any suggestions or part numbers for oem or compatible substitutes? Is compatible substitutes kind of redundant? LOL! Hopefully tower hobbies has...
Last post
I hav e some original Ultra brushes of various types stashed away - howmany sets do you need?
HI, I just joined. I'm looking to buy a new charger and I would like it to charge two batteries at the same time. I want it to charge lipos to. Does anyone have an opinion on the Mega Brain 977?
Last post
Thanks everyone for the input! Has anyone seen the new duratrax chargers? I'm interested in the Onyx 230. Thanks again.
So has anyone experimented with gearing an RC10 for a brushless system? It's been stated that the 6 gear may not handle a brushless/Lipo system so well, but how have people geared the Stealth and with what battery/motor combination? I'm interested...
Last post
For BL setups, consider the Speed Passion setup. Im looking to pic up a unit through my motor builder (shameless plug: ) They seem to be very good and competitive.
At my local track, our vintage class allows for Lipo, but still running brushed...
so, is this a must have , or a wouldn't hurt to have when using lipo packs?
Last post
Over discharging does not cause fires or other dangerous situations. Overdischarging ruins the chemicals inside a LiPo to the point where it won't take a complete charge again, and will never perform the way it was when it was new. The only way...
I picked up a couple of Duratrax Piranha 1900mh 7 cell packs. i charged them up, put one in my 5700kv brushless powered truck, and headed to the parking lot across the street. After a few minutes of light running, the trucks throttle was stuttering...
Last post
i have a 2.65 transmission 21t pinion 87t spur. i have been running some 3300mh ni-mh packs with no issues.i guess i'll try gearing a little lower and
lower the timing advance when running the cheaper packs.
i'm not sure when i'm getting the...
i want to make an order from tower for a few things, but they arent selling nomadio stuff anymore, and i really need another reciever for my nomadio react. will a futaba 2.4ghz reciever work? i know the...
Last post
Has anyone used one of those Losi spektrum receivers? Have you heard any complaints? I read that they are compatible with Spektrum and are much cheaper too. How do they compare in size?
The losi rx does work fine with the standard spektrum stuff....
Have any of you used a Dynamite Tazer 15T ESC? Its pretty cheap and thought it might be ok in my buggy I just got. I can't find the specs for it so you guys can look at it. I only get to spend 100bucks for electronics and motor. I don't want stock...
Last post
Here's my thought. How much is the ESC? Put in a couple exra bucks and you can get a used Cyclone or GT7 off of ePay. These ESC's can take any motor.
Lower end ESC's suffer from slow acceleration and if you do run them with a 15T, they will heat up...
I have an Airtronics CS2P radio and the foam rubber on the transmitter steering wheel has dried out and is going to start falling apart soon. Has anyone replaced this material before and what did you use? It is currently some kind of foam material...
Last post
I recently bought an adaptor for my old KO radio to take a Tamiya wheel,dont know if anything is available for Airtronics though.
Does anybody use stick radios anymore? I went to the store today to pick one up and found my options very limited. The shopkeep told me that no one uses them. I feel like such a dinosaur.
Last post
Im still running my original faviorite from 87,Acoms tecniplus.To activate servo reverse you simply undo the gimble and spin it round.Talk about features,this things full of them.
Just a thought. I have an old Traxxas XL-1, and wonder if I can use it and a 6-Cell to make a decent compact power supply for a lathe. I dont see why not, but what do I know? I dont want to ruin anything.
Last post
Well, it just so happens, I have several Brand New MSCs I dont/wont use, and only a couple extra ESCs. So, I believe I will be hooking up one of the MSCs for my Lathe.
Although I have several ruined Stick Packs that probably have 1 or 2 good cells...
Users browsing this forum: No registered users and 9 guests
Forum permissions
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum You cannot post attachments in this forum