Ball raced steering bearing sizes
Ball raced steering bearing sizes
I'm buying one of these alu steering sets for my 10t:
http://cgi.ebay.com/Associated-RC-10GT-Blue-Bushing-steering-/200556470804?pt=Radio_Control_Parts_Accessories&hash=item2eb218e214
It says it has 5x8 delrin bushes now would this mean i need 5x8x2.5 bearings to go in there as this is the only size i can find that matches on avidrc?
I can wait if needs be but need to put in an order for quite a few bearings so wanted to get it all done in one load.
If anyone can help it would be much appreciated
http://cgi.ebay.com/Associated-RC-10GT-Blue-Bushing-steering-/200556470804?pt=Radio_Control_Parts_Accessories&hash=item2eb218e214
It says it has 5x8 delrin bushes now would this mean i need 5x8x2.5 bearings to go in there as this is the only size i can find that matches on avidrc?
I can wait if needs be but need to put in an order for quite a few bearings so wanted to get it all done in one load.
If anyone can help it would be much appreciated
- PBR Allstar
- Approved Member
- Posts: 805
- Joined: Mon Apr 30, 2007 10:30 pm
- Location: Sonoma, Ca
- Has thanked: 1 time
- Been thanked: 3 times
- PBR Allstar
- Approved Member
- Posts: 805
- Joined: Mon Apr 30, 2007 10:30 pm
- Location: Sonoma, Ca
- Has thanked: 1 time
- Been thanked: 3 times
Re: Ball raced steering bearing sizes
Just remember, running the GT bellcranks on a 10T will change the geometry a little bit. the 10T bellcranks were a little longer from the pivot to the ball studs than the GT.
Let us know how it works out.
Let us know how it works out.
-
- Approved Member
- Posts: 328
- Joined: Mon May 03, 2010 5:20 pm
- Location: Southern California, USA
Re: Ball raced steering bearing sizes
Those will be too short if mounted on a RC10T causing bump steer problems without drilling new holes in the chassis. GT holes are much closer to the front bulkhead.
Re: Ball raced steering bearing sizes
Hmmm i didnt realise this i thought the nose plates were exactly the same and that was why you could use the standard plastic gt bellcranks on the 10t. So if i'm gonna do this i gotta buy me a gt noseplate as i'm not drilling my 10t nose. Is there no other ballraced steering that will bolt on the 10t?
Glad i had some feed back from you guys before i went and bought the steering!
Glad i had some feed back from you guys before i went and bought the steering!
-
- Approved Member
- Posts: 328
- Joined: Mon May 03, 2010 5:20 pm
- Location: Southern California, USA
Re: Ball raced steering bearing sizes
The only ones I seen is from MIP vintage stuff. I was using the stock ones on my RC10T Duratrax conversion until I seen these on Ebay.
I use an A&L steering and made a custom front adjustable bracket.
Just some of the options you can do.
I use an A&L steering and made a custom front adjustable bracket.
Just some of the options you can do.
Create an account or sign in to join the discussion
You need to be a member in order to post a reply
Create an account
Not a member? register to join our community
Members can start their own topics & subscribe to topics
It’s free and only takes a minute
Sign in
-
- Similar Topics
- Replies
- Views
- Last post
-
- 5 Replies
- 1497 Views
-
Last post by Group B
-
- 4 Replies
- 318 Views
-
Last post by Bormac
-
- 1 Replies
- 694 Views
-
Last post by aip47-2008
-
- 4 Replies
- 1092 Views
-
Last post by romulus22
-
- 3 Replies
- 852 Views
-
Last post by janaya
-
- 7 Replies
- 853 Views
-
Last post by ericsp2
-
- 5 Replies
- 1032 Views
-
Last post by AscotConversion
-
- 32 Replies
- 10265 Views
-
Last post by 85Edinger
Who is online
Users browsing this forum: No registered users and 21 guests