So I finally have just about everything together to finish and start my runner build.
here's where i'm sitting so far
Andy's arms F/R
B4 Shocks
rere chassis
RC Carbon shock towers F/R
Stealth tranny
Some alloy steering and front end blocks that I bought off here a while ago
I have B4 front end parts and rear carriers, I just ordered a screw kit from Tony's
I started with Dynotech rear arms and I had MIP CVD's for them but now I want to use the Andy's arms and the CVD's are too long. Which CVD's should I be using?
Sorry about the pics I used my ipad and not my good camera
Adams rere OIN Frankenbuild
- bully
- Approved Member
- Posts: 759
- Joined: Mon May 31, 2010 6:08 am
- Location: Perth W.A Australia
- Been thanked: 6 times
Re: Adams rere OIN Frankenbuild
Standard rc10 or b2 b3 cvds work with andys arms but unsure with b4 rear hubs. I have andys arms on my graphite with 1an half degree t2 rear hubs or 10t 0 an 3 degree hubs
- losiXXXman
- Approved Member
- Posts: 936
- Joined: Sat Aug 29, 2009 9:53 am
- Location: Cary, NC
- Been thanked: 5 times
Re: Adams rere OIN Frankenbuild
I think the formula is B44 rear cvas when using stock geometry arms and B4 hubs. Which wheels you want to use determines which rear hubs you want to use. Modern offset wheels = B4 hubs, and B44 cvas. Old school dished wheels = og hubs (or equivalent) and the B3 cvd.
- abailey21
- Approved Member
- Posts: 273
- Joined: Sun Feb 13, 2011 8:28 am
- Location: Leander TX
- Been thanked: 2 times
Re: Adams rere OIN Frankenbuild
I thought thats what I bought (B44 CVD's) of course I didn't keep the header card or write down what I used.
I might just have to go back to the Klein arms in the rear but I can't find fronts **I haven't exactly looked either**
Here's some pics of a little progress;
I'm not going to use the new screws until final assembly and I still need a rere rear bulkhead cause mines stripped and I'll need to dye the white to back to match everything but this is the closest I've been in 3 years to finishing this!
I might just have to go back to the Klein arms in the rear but I can't find fronts **I haven't exactly looked either**
Here's some pics of a little progress;
I'm not going to use the new screws until final assembly and I still need a rere rear bulkhead cause mines stripped and I'll need to dye the white to back to match everything but this is the closest I've been in 3 years to finishing this!
Create an account or sign in to join the discussion
You need to be a member in order to post a reply
Create an account
Not a member? register to join our community
Members can start their own topics & subscribe to topics
It’s free and only takes a minute
Sign in
-
- Similar Topics
- Replies
- Views
- Last post
-
- 9 Replies
- 3590 Views
-
Last post by V12
-
- 5 Replies
- 1027 Views
-
Last post by Brandon G
-
- 4 Replies
- 836 Views
-
Last post by Charlie don't surf
-
- 18 Replies
- 2931 Views
-
Last post by KrAcOn
-
- 22 Replies
- 1879 Views
-
Last post by GoldRush
-
- 184 Replies
- 15931 Views
-
Last post by RC10th
-
- 5 Replies
- 981 Views
-
Last post by Synergy
-
- 66 Replies
- 8034 Views
-
Last post by RanchoJim
Who is online
Users browsing this forum: No registered users and 14 guests