How to cut and drill chassis for RPM kit?
- ra272
- Approved Member
- Posts: 312
- Joined: Fri Nov 17, 2006 9:32 am
- Location: NANCY FRANCE
- Been thanked: 7 times
How to cut and drill chassis for RPM kit?
Hello, can someone explain me precisely how to cut and drill a team car chassis to fit properly the RPM kit? has someone a template?
I'm talking about this kit:
To fit on this chassis:
Thank you very much.
I'm talking about this kit:
To fit on this chassis:
Thank you very much.
- mikedealer
- Approved Member
- Posts: 1778
- Joined: Fri May 18, 2007 12:25 am
Re: How to cut and drill chassis for RPM kit?
there is a drill and cut template out there.. i dont have one personally
- Asso_man!
- Approved Member
- Posts: 3959
- Joined: Thu Aug 03, 2006 7:49 am
- Location: EU
- Has thanked: 40 times
- Been thanked: 70 times
Re: How to cut and drill chassis for RPM kit?
I have one, if you like, I could lend it to you, but you'll be in charge of the double shipping fees (from Brussels to Nancy and back to me), just let me know
_____________________________________________
_____________________________________________
Come and visit the stable
_____________________________________________
Come and visit the stable
- scr8p
- Administrator
- Posts: 16540
- Joined: Tue Feb 07, 2006 9:46 pm
- Location: Northampton, PA
- Has thanked: 28 times
- Been thanked: 976 times
Re: How to cut and drill chassis for RPM kit?
I took a "Stealth Ready" Chassis and bolted it to the "6-Gear" Chassis, bottom to bottom, and drilled it that way. Seems to have worked just fine. Or is there some reason that shouldnt/wouldnt work (I havent actually driven it yet)?
- scr8p
- Administrator
- Posts: 16540
- Joined: Tue Feb 07, 2006 9:46 pm
- Location: Northampton, PA
- Has thanked: 28 times
- Been thanked: 976 times
Re: How to cut and drill chassis for RPM kit?
that template is to modify the rear of an rc10 chassis to use the worlds rear suspension. this is the template to drill for a stealth.MONSTER wrote:I took a "Stealth Ready" Chassis and bolted it to the "6-Gear" Chassis, bottom to bottom, and drilled it that way. Seems to have worked just fine. Or is there some reason that shouldnt/wouldnt work (I havent actually driven it yet)?
Re: How to cut and drill chassis for RPM kit?
*anybody remember who Emily Latela was*
"Ooo, wel, that quite different...... Nevermind!!"
But, should the way I did the Tranny holes be OK?
"Ooo, wel, that quite different...... Nevermind!!"
But, should the way I did the Tranny holes be OK?
- ra272
- Approved Member
- Posts: 312
- Joined: Fri Nov 17, 2006 9:32 am
- Location: NANCY FRANCE
- Been thanked: 7 times
Re: How to cut and drill chassis for RPM kit?
I think I can do my own template with this picture, thanks.
Create an account or sign in to join the discussion
You need to be a member in order to post a reply
Create an account
Not a member? register to join our community
Members can start their own topics & subscribe to topics
It’s free and only takes a minute
Sign in
-
- Similar Topics
- Replies
- Views
- Last post
-
- 5 Replies
- 970 Views
-
Last post by lowrydesign
-
- 14 Replies
- 1110 Views
-
Last post by fordtransman
-
- 7 Replies
- 474 Views
-
Last post by jcwrks
-
- 0 Replies
- 1710 Views
-
Last post by mytimac
-
- 7 Replies
- 1111 Views
-
Last post by kaszal
-
- 7 Replies
- 922 Views
-
Last post by m_vice
-
- 0 Replies
- 553 Views
-
Last post by SoAzRC
-
- 5 Replies
- 819 Views
-
Last post by acerpower1
Who is online
Users browsing this forum: No registered users and 1 guest