Search found 9 matches

by advintage
Sun Jun 14, 2020 12:03 pm
Forum: RC10 Truck Forum
Topic: DuraTrax Sixpack ST 2.8 Tires on T4
Replies: 2
Views: 972

Re: DuraTrax Sixpack ST 2.8 Tires on T4

OK, so since this post did not get any answers I will go ahead and answer it myself based on the research I have done since I posted the question. Maybe this will help someones else. Basically, you can get the 2.8 or the 2.2, typically 2.2 is for buggys. The inner diameter of the plastic wheel part ...
by advintage
Mon Jun 01, 2020 1:21 pm
Forum: 21st Century Modern
Topic: Wheel nut falling off T4
Replies: 4
Views: 814

Re: Wheel nut falling off T4

I have the hex conversion on this wheel. Also, note I'm ripping in the grass too when this happens.
by advintage
Sun May 31, 2020 11:36 pm
Forum: 21st Century Modern
Topic: 3pv noticeably faster than m8?
Replies: 0
Views: 629

3pv noticeably faster than m8?

I'm looking to run 1 tx for b4 and t4(s) w/ multi receivers. Have an old airtronics m8 that I really like w/ 92836 rx, and looking to add Novak Electronics Switch Synthesized FM Module w/ XXTRA Receiver(s). Or looking to get a Futaba 3pv S-FHSS Radio System w/R203GF Receiver(s). Will the R203GF Rece...
by advintage
Sun May 31, 2020 11:24 pm
Forum: 21st Century Modern
Topic: Wheel nut falling off T4
Replies: 4
Views: 814

Wheel nut falling off T4

Running a gtb/novak 6.5 which is ballooning the tires and ripping them off too! FT nut just bought and replaced is very tight but coming off. Do I need thread locker or does the wheel falling off mean something with the drive train or tranny is not smooth?
by advintage
Sat May 09, 2020 3:25 pm
Forum: RC10 Truck Forum
Topic: DuraTrax Sixpack ST 2.8 Tires on T4
Replies: 2
Views: 972

DuraTrax Sixpack ST 2.8 Tires on T4

Was wondering if anyone has run DuraTrax Sixpack MT 2.8 Mounted Truck Tires 2WD C2 on a RC10T4? My questions, if so: do I get the 2.8 or the 2.2 and I heard you should have a half inch offset on these, so does that mean a half inch offset on the back and the front? and if with this offset does that ...
by advintage
Sat Apr 25, 2020 10:15 am
Forum: 21st Century Modern
Topic: What needs greased and oiled on RC10T4
Replies: 2
Views: 975

Re: What needs greased and oiled on RC10T4

Code: Select all

Heatshrink is a common trick to keep the pin from falling out


Nice trick, thanks!
by advintage
Fri Apr 24, 2020 5:39 pm
Forum: 21st Century Modern
Topic: What needs greased and oiled on RC10T4
Replies: 2
Views: 975

What needs greased and oiled on RC10T4

Hey, can anybody help me with a maintenance "what needs greased and oiled and when" question? I have two RC10T4 trucks that I have not run in probably five years, and they are probably both about 5 to 10 years old and I bought them used on eBay, so I was wondering before I run these what s...
by advintage
Mon Apr 20, 2020 12:20 pm
Forum: 21st Century Modern
Topic: discontinued parts for rc10t4
Replies: 4
Views: 1853

Re: discontinued parts for rc10t4

Ok, thanks! Do you know if this one also works (w/o pins) Part# ASC31367 Team Associated CVA Rebuild Kit https://www.amainhobbies.com/team-associated-cva-rebuild-kit-asc31367/p220325
by advintage
Sun Apr 19, 2020 11:28 am
Forum: 21st Century Modern
Topic: discontinued parts for rc10t4
Replies: 4
Views: 1853

discontinued parts for rc10t4

Hi, How do I get replacement parts for rc10t4 if they are discontinued? Can I use parts from newer rc10ts?

I need this part https://www.associatedelectrics.com/teamassociated/parts/details/7381-ASC7381-mip_cvd_uni-drive_rebuild_kit/

Go to advanced search