RC10Talk - The Net's Largest Vintage R/C Community

Wing:

Tamiya M04 build week recently.... gave this the once-over, ready for a new home: M04_01.jpg M04_02.jpg and built these up from a big lot of parts I got a little while ago: M04_03.jpg Sadly, I don't have any spare 225mm Mini bodies other than a couple of Protoform SoCal panel wagons.... so they will...

PETG is slightly different from PET. I don't know the exact difference. For sure it's easier to handle than Lexan, because the temperature range for vacuum forming is uncritical. And it's quite easy and cheap to find. Lexan paint seem to work well. I don't know about the durability (especially compa...

OK guys, raffle time! Some of you have seen this already in my build thread. Now you have a chance to own it. Like the previous raffle, a $5.00 donation to the forum will get you 1 chance. $10.00 will get you 2, $15.00 for 3.... and so on. Only donations made between March 1st and March 31st are eli...

Finished!

Here is an RC10 buggy that I am very fond of. I purchased this many many years ago from our good friend Don, RIP buddy. A few details, it has Andy's arms up front, RPM's on the back. Anodized chassis and such. LRP Runner speed control and a Futaba S3003 servo. Thanks Don. 20230308_155028.jpg 2023030...

This is the Outlaw ll...highly modified Tamiya Bruiser...here is a build thread
https://www.rc10talk.com/viewtopic.php?t=47544

Got this old Blackfoot. Now that its in front of me, I can see all the broken parts that weren't visible in the pictures.

Original Tamiya Midnight Pumkin (not rerelease)...ran hard for many years in early 2000s...set up on 10 cells and a trinity speed gems amber motor (long before days of brushless motors and lipo batteries). Clocked it at 48mph on gps. It was a handful and took a horrible crash. It was restored with a...

Place holder

Custom Clodbuster

New Era tube chassis
Novak super rooster speed control
Jps aluminum wheels.
Proline giant trac tires
Parma hemi motor
Custom painted body
Driver with gauges/dash
Blue Anodized threaded shocks
Trinity Speed gems 2 motors (Jade15x4)

Proline rc10 hot trick truck conversion with original mip trans and steering

Unexpectedly, Pinky's litter mate came available. I really wasn't looking to get a 2nd Top Cat, but thought I should take it in on the off chance that I need one because there's a sudden Schumacher apocalypse. Apparently not everyone is drawn to the extreme level of weirdness that the Top Cat has, a...

A stream of deliveries over the last few days... Some elements for my printing ongoing projects arrived today (printer, post processing station, isopropylique acoohol and resin). This was expected with an accurate tracking... But there was a package incoming from Australia as well, which I did not e...

Here’s a look at the different motor plates.. Mini JrxT has holes for 14-16 tooth pinions and comes with a 15t. https://i.postimg.cc/mg3mnCZb/1B6530FF-64E1-41B4-8919-FBE304373D16.jpg Mini Jrx2 has holes for 17-19 tooth pinions and comes with a 17t. https://i.postimg.cc/wjYWF0pf/676916FE-A8C4-4FC3-AC...

This is my RC10 A+ chassis 6 gear buggy. It's gone through a little bit of front end evolution to replace the nose tube setup and lower the bellcranks a bit. https://www.rc10talk.com/viewtopic.php?f=35&t=47355 RC10B6 chassis, trimmed and modified Trinity Modified Litespeed Litesink Hitec Shredde...