another chassis id please drag car?
-
- Approved Member
- Posts: 1304
- Joined: Tue Dec 08, 2009 10:10 pm
- Location: seattle washington
another chassis id please drag car?
i got this this week shouldn't have but hey early christmas present
i have seen this chassis somewhere but cant remember where any help would be great
i think the front is a bit to wide maybe if i put some wider slicks on the rear ?
Paul
i have seen this chassis somewhere but cant remember where any help would be great
i think the front is a bit to wide maybe if i put some wider slicks on the rear ?
Paul
- drbelleville
- Approved Member
- Posts: 815
- Joined: Wed May 20, 2009 5:03 am
- Location: My Adopted state - Texas
- Been thanked: 1 time
Re: another chassis id please drag car?
The front end seems to be from a TRC car, and the rear pod may be comprised of Bolink side pod plates. I am not sure about the chassis, I tried looking through what I have, but did not see one like it yet. Lazerlite, Fine, etc. I am still looking though.
Maurice
Maurice
- Eau Rouge
- Approved Member
- Posts: 2225
- Joined: Sat Jul 29, 2006 11:59 pm
- Location: Aurora, Illinois
- Has thanked: 2 times
- Been thanked: 2 times
Re: another chassis id please drag car?
Parma or Bolink rear end, with a scratch-built chassis. Front end is a Delta/TRC-style beam. Way too wide, at that. There wasn't anything on the market that looked like that from any drag companies that I know of. I could be wrong. There were a lot of low-end "Street" kits out there with muscle car or hot rod bodies on them without much in the way of performance. Could be anything, or it could be something fabricated up by the original owner. Hard to say. Nothing real special, though.
What's the EXACT wheelbase?
What's the EXACT wheelbase?
-
- Approved Member
- Posts: 1304
- Joined: Tue Dec 08, 2009 10:10 pm
- Location: seattle washington
Re: another chassis id please drag car?
10"1/2Eau Rouge wrote:What's the EXACT wheelbase?
i feel daft i,m sure i saw the same chassis on a search drag rc or something but now can,t find it ]
the axel is home made and the front is a touch wide
i will keep looking i have a 10 turn and a tekin to go in it and would like to put the right front end on it .
Paul
- PBR Allstar
- Approved Member
- Posts: 805
- Joined: Mon Apr 30, 2007 10:30 pm
- Location: Sonoma, Ca
- Has thanked: 1 time
- Been thanked: 3 times
Re: another chassis id please drag car?
I have to imagine that front axle would be easy to narrow though? clamp it up and drill a couple new kingpin holes.
- PBR Allstar
- Approved Member
- Posts: 805
- Joined: Mon Apr 30, 2007 10:30 pm
- Location: Sonoma, Ca
- Has thanked: 1 time
- Been thanked: 3 times
Re: another chassis id please drag car?
What he said ^ Lots of members with milling machines here if you decide to go that route
- drbelleville
- Approved Member
- Posts: 815
- Joined: Wed May 20, 2009 5:03 am
- Location: My Adopted state - Texas
- Been thanked: 1 time
-
- Approved Member
- Posts: 1304
- Joined: Tue Dec 08, 2009 10:10 pm
- Location: seattle washington
Create an account or sign in to join the discussion
You need to be a member in order to post a reply
Create an account
Not a member? register to join our community
Members can start their own topics & subscribe to topics
It’s free and only takes a minute
Sign in
-
- Similar Topics
- Replies
- Views
- Last post
-
- 18 Replies
- 1390 Views
-
Last post by Retro-RC.co.uk
-
- 3 Replies
- 1199 Views
-
Last post by KidAgain
-
- 6 Replies
- 1930 Views
-
Last post by Basher67
-
- 4 Replies
- 858 Views
-
Last post by KidAgain
-
- 6 Replies
- 1407 Views
-
Last post by Maxell27
-
- 9 Replies
- 1637 Views
-
Last post by kenny21
-
- 18 Replies
- 4187 Views
-
Last post by Eau Rouge
-
- 8 Replies
- 2373 Views
-
Last post by Basher67
Who is online
Users browsing this forum: ahenderl, Haggy38, morrisey0 and 10 guests