RC10Talk - The Net's Largest Vintage R/C Community

Hey guys, doing one of those custom GT5 conversions! Whoever made this chassis kit totally botched it and I had to machine quite a few things just to make it useable but I've pretty much got the truck complete now! Just looking for some advice on where to put the battery and if anyone has a manual o...

Hey guys, hope everyone is doing well and enjoying all the new re-releases! I'm currently running my custom GT with an OS Max 18TZ and having some serious issues. The car is insane and when I had it running right, it was a blast! But after a few minutes the brakes were cooked. Attached is a YouTube ...

Thanks you guys, appreciate the love! Frankentruck all the way for me! What should I use to upload images next time??

My custom arcade GT! https://i.ibb.co/n19CyV6/3-C5-C7-ED1-5-E7-D-4-C81-889-C-322698069-E5-E.jpg https://i.ibb.co/pn89FVr/92856591-9-A33-495-F-867-B-9-A32-DFA57-E9-D.jpg Sporting an OS Max 12CVR with MiP heavyweight flywheel and MiP 2 in 1 clutch, RRP clutch bell and spur, full RRP transmission with ...

Thanks for the heads up, that’s awesome! Going to try to grab one. Would absolutely love to see a GT rerelease or GT3 but I can only dream lol

Not sure on the rarity especially being in the condition it’s in but haven’t seen many go up for sale: RPM ultra chassis

I wonder if MIP Pucks or Kyosho RB7SS outdrive spacers would work. Custom works lists theirs as in stock. Which outdrive part number did you end up using? Thanks for the heads up, I’ll order a couple spare sets! Had to cut mine up to clear the spur gear on my GT so figured I may need an extra. I fo...

Hey guys, hope y’all are doing well. Went to a hobby store a few hours away from me and found a decent little haul of NOS parts including an OS Max 12CV in a red OS box with a see through plastic lid. I’ve never seen a box like that so I asked him to set it aside for me and will be going back next w...

I’ll do some researching but I think I’ll try and get them to work, can’t find many decent options for a good price!

I love the washers, they look awesome too. Bought the complete B4 bearing carriers with axles, spacers and CVD’s for $40 USD, couldn’t find much else.

Are you using rear wheels meant for 3/16" axles? If you are and are still destroying them, you could add the little washer shim that the B4 & T4 use. It will allow you to lock the wheel in place to it when you tighten the rear axle nut. That should make it harder for the axle pin to destro...

Hey guys, forgot to add this to the main post! The reason I’m doing this swap is because ever since I installed the RPM rear oversized bearing carriers I keep destroying wheels. I’m running shiny MIP CVD’s and 3/16 axles with real 1/2x3/16 bearings and I left the shim placement stock (thick shim on ...

...even made my own T3 A-arms all by hand. Any help is appreciated, thank you! Those T3 arms are nice work. www.ebay.com/itm/294264008216 ...bolt on the hex wheels and go. Unless you enjoy being a masochist... err, I mean, machinist. :mrgreen: :lol: Thank you sir, more work than it’s worth lol and ...

Welcome to the board. There are a few different ways to get hex on to a T/T2/GT. If you have machinating experience you can make these parts work. The blocks will need to be milled down to fit in the GT front arms and the hinge pins drilled out to accept the larger 1/8" arm pins. You may need ...

Welcome to the board. There are a few different ways to get hex on to a T/T2/GT. If you have machinating experience you can make these parts work. The blocks will need to be milled down to fit in the GT front arms and the hinge pins drilled out to accept the larger 1/8" arm pins. You may need ...

Hey guys, I hope everyone is doing well! Just been researching how to get hex wheels on my two RC10GT’s and I have a few questions. I’ve seen all the posts about the T4 hex axle swap but can only find one auction on eBay for the parts I would need. So I found this complete front end set up for the T...