RC10Talk - The Net's Largest Vintage R/C Community

Dadio wrote: ↑Sat Jul 13, 2024 4:22 am

THEYTOOKMYTHUMB wrote: ↑Fri Jul 12, 2024 9:31 pm Found this cute little fella near the driveway today.

the males don't have enough force to really hurt you but the females can

But don't they ALL?

Oregon Coast, 5 days with the fam! Unbelievable!

Great test results. Learned a few things as well it is going to be a useful result. IMG_5007.jpeg The chassis was resin light. The vacuum held, but the resin from the top did not diffuse to the outside layers. The cosmetic effect of the 3 piece wasn’t great. There were lots of orphan strands of carb...

IMG_5046.jpeg This is rigid and impossibly light. Cosmetically it’s going to need a few hours of clean up but it should be just fine for my oldest who wants to make his rc10t as a model and not a running car. I’m not sure if it’s the switch in resin, design or better technique. I think I may trim i...

Good gear box mod! Next up you need a Hot Box propeller shaft splitter by ODS Racing and Development, Ishihara

Link to my Hot Trick Hotshots https://www.rc10talk.com/viewtopic.php?p=525572&hilit=hot+trick+hot+shot+x+2#p525572

I got contacted by someone searching for a Zerda bumper... I never tested it, so printed one in TPU to see... https://i.imgur.com/POiYKBH.jpeg The dimensions, profile and holes position are perfect, only the cuts profile are not perfect. I may do something about it at some point, but for the time be...

A new printer arrived home during the week... Elegoo Saturn 4 Ultra https://i.imgur.com/TlFP0Du.jpg The bed is bigger than the Photon M3, and this should become my main resin 3D printer. I don't know yet if I'll keep the Photon M3, as I have no clue if this big bed printer will work with flex resins...

Multiple fails... Cumulating new printer, new resin, new slicer (Chitubox in version 2 is slightly different than V1). this makes the thing slightly more difficult. The resin is not an easy resin, and I start to suspect the tilt makes orientation of parts slightly more difficult... I resliced my par...

Well how about that. Thanks for posting this up since I hadn't seen it yet. It only took 33 years for me to enter a build.

This time it is a success. I changed the supports settings accordingly to some tricks I found on a the sirayatech user group on facebook, added a few supports just to be sure, and it worked... AficI8ZkkiA I removed the supports and put the parts in the cure station after cleaning... https://i.imgur....

Made some updates to my original Ten4 project. Jeff helped with the conversion to use original tires. Added Factory works motor and using the cc chassis parts and screws. I installed Dhawk 3 piece wheels. Mostly silver and black with some gold. I haven’t finished tweaking the colors.

- limestang

Chased the 4014 for a little ways today. It was a couple hours from home and my timing was bad, almost missed it. Literally parked as it was coming around for the bend. Ended up stopping at the bend for a quick lube job

Milford Sound, lower South Island, New Zealand, got real lucky with the sun set and mist

Also a few other bits to add eventually, not sure about the electronics yet, I am planning to run it. Team Penguin does an undertay and gear cover, the rest is TBG, always quality. Belts (TM17) were hard to source, found tough racing, but they have a sketchy looking website and wouldn't ship to New ...

Cheers Dadio,
You cant see the swarms of sandflies that come out at some times of the day,
This was the next day at the Blue Lake, Saint Battens, Central Otago light is hard to replicate.