Search found 53 matches

Return

by Chamberlain
Wed Nov 16, 2011 8:23 pm
Jump to forum
Jump to topic

Re: JRX series set up discussion

I remember when I got my first production JRX and Rick Hohwart still had his Prototype and hadn't gotten the new produciton parts yet. We were at the Regionals in AZ 1988 Region 12 if I remember. Not sure if it changed or not. It was the qualifier for the 1989 Worlds. We were cleaning our cars and I...
by TRX-1-3
Fri Jan 22, 2021 11:14 am
Jump to forum
Jump to topic

Re: JRX2 - The project.

Amazing work on that chassis! When I saw that first picture, I thought it was dead. But you saved it. Nicely done.
by matt1ptkn
Fri Jan 22, 2021 11:40 am
Jump to forum
Jump to topic

Re: JRX2 - The project.

Well done! The printed parts and chassis repair look spectacular!
by GoMachV
Sun Jan 24, 2021 3:14 pm
Jump to forum
Jump to topic

Re: JRX2 - The project.

The brass gear wore out quickly, it was a running change by losi
by mytimac
Tue Jan 26, 2021 12:47 am
Jump to forum
Jump to topic

Re: JRX2 - The project.

I have a question for you: Why are the top shaft different between the two gearboxes? Design change from Losi or aftermarket? 20210124_110642.jpg Talked to Gil about this a few years ago. The actual issue was consistency of product. The brass gear didn't always get pressed on the to the shaft at th...
by Rlayman
Wed Jan 27, 2021 11:08 am
Jump to forum
Jump to topic

Re: Getting Closer to a build

Yup. Sacrificed the bottom plate, but no damage to the transmission or rear bulkhead. It was to be replaced anyway.
by Dadio
Wed Feb 03, 2021 5:21 pm
Jump to forum
Jump to topic

Re: My racing days Hotshot replica hopefully

Hi, I wish I had old photos like you have. Very cool! I once started with a Hotshot and I still have that car. I will always have a soft spot for the Hotshot and got really inspired by your build. Might have to get a re-re and build something crazy. :) Is that chassis available from Factory Works? ...
by mikea96
Tue Feb 09, 2021 5:28 am
Jump to forum
Jump to topic

Re: JRX2 - The project.

Looks great nice restoration.
by mikesofunny
Tue Feb 16, 2021 11:34 pm
Jump to forum
Jump to topic

Re: Looking for top shaft diemnsions

This is a XXT CR Hydradrive shaft

Edge of pin to outer end of shaft
20210216_172400.jpg
End of shaft to flat
20210216_172453.jpg
Inner end of shaft to flat
20210216_172540.jpg
Edge of E-clip groove to flat
20210216_172702.jpg
Hope this helps
by mikesofunny
Thu Feb 18, 2021 4:57 am
Jump to forum
Jump to topic

Re: Looking for top shaft diemnsions

My bad. Forgot it was flat on both sides and not D shaped. It was the 3,2 measurement i was loking for. 1/8" i guess... :wink: I have most parts for a XX slipper as spares in my old box of rc stuff. Would like to fit it to a LRM transmission but is missing the top shaft. Thinking of having one...
by adam lancia
Thu Feb 18, 2021 10:37 am
Jump to forum
Jump to topic

Re: Looking for top shaft diemnsions

No apology necessary! Good luck with your project.

mikesofunny, thanks for the extra measurements!
by matt1ptkn
Thu Feb 18, 2021 11:35 am
Jump to forum
Jump to topic

Re: Looking for top shaft diemnsions

Here are the dimensions for the LRM Hydradrive/slipper top shaft.
by GoMachV
Thu Feb 18, 2021 6:30 pm
Jump to forum
Jump to topic

Re: Novak design team - Dually

jwscab wrote: Thu Feb 18, 2021 6:24 pm that happens a lot. sometimes you see initials etched into PCBs, or even cooler, initials photolith'ed onto IC dies.
I love what Tesla did here haha
by AscotConversion
Sat Feb 20, 2021 11:17 pm
Jump to forum
Jump to topic

Re: Novak design team - Dually

REN is probably Bob Novak, and ASK is probably Adnan Khan. THP might be Tyree Phillips.
by works92
Mon Feb 22, 2021 9:48 am
Jump to forum
Jump to topic

Re: Post Pictures of your Losi Vehicles

My Losi XXcr
still doing some race up to 2010, but now in his shelf version.

Image
Image