That does look a bit sus.
The finish looks like Goldfinger painted it.
Search found more than 1037 matches
- Tue May 14, 2024 12:16 pm
- Jump to forum
- Jump to topic
Re: rc12e - how to get started with it
What is the ground clearance supposed to be? Maybe the tires are worn down? The ground clearance back in the day was the minimum you could get away with without scraping/dragging (getting slowed down. On road oan cars are meant for smooth surface needing minimal clearance. The downside of truing th...
- Tue May 14, 2024 3:45 pm
- Jump to forum
- Jump to topic
Re: So what did you get in the post today ???
Uh oh, more red racers!
- Fri May 17, 2024 4:35 pm
- Jump to forum
- Jump to topic
Re: RC10 Classic 40th anniversary
Stealthboy2600 did a nice job with his in gunmetal gray
. https://www.rc10talk.com/viewtopic.php?p=566263#p566263
. https://www.rc10talk.com/viewtopic.php?p=566263#p566263
- Sat May 18, 2024 12:30 pm
- Jump to forum
- Jump to topic
Re: My first RC10T. But, what is it?
After reading your previous post, I went back and had a closer look. My truck has two left arms. :( I could try to find a right arm but I can't be bothered. I'll just make a shallow notch so both sides have the same droop. I probably have an extra right arm, if that's the same as the GT or the T2. ...
- Sat May 18, 2024 6:38 pm
- Jump to forum
- Jump to topic
Re: RC10 Graphite Resto
Nice collection of part for the build. The gold motor guard is a nice addition. The factory graphite is my favorite version on RC10.
- Sun May 19, 2024 5:14 pm
- Jump to forum
- Jump to topic
Re: Franken Dead Pool DS-ish Car, restomod version
So that Futaba ESC that went up in smoke was 100% my fault. Reverse polarity is a bad thing. Oops. That's ok though, I really don't like the single speed reverse and wanted Lipo protection. The DS chassis setup is working pretty well... . 1000011036.jpg . ... until I see that it gives me too long of...
- Sun May 19, 2024 6:00 pm
- Jump to forum
- Jump to topic
Re: Franken Dead Pool DS-ish Car, restomod version
You should be able to move the rear arm mounts forward to shorten the wheelbase. Looks like you're in long wheelbase setup right now. I hadn't even noticed that was where I had the rear arm mounts. Thanks for spotting it. 👍 I'm also noticing the front is a bit narrow. A set of GT long front axles i...
- Sun May 19, 2024 9:14 pm
- Jump to forum
- Jump to topic
Re: Franken Dead Pool DS-ish Car, restomod version
I forgot the cutouts in the chassis sidewalls to let me use the short wheelbase position, but some minor trimming took care of that. Now the wheelbase is a good match for the body. With the wide 7222 front axles installed, so is the front track width. . 1000011043.jpg . It's moving along nicely now....
- Mon May 20, 2024 3:49 pm
- Jump to forum
- Jump to topic
Re: Picture of the day. (Taken by you)
1 blade, ok. 2 blades? Don't even think about it.
- Mon May 20, 2024 5:33 pm
- Jump to forum
- Jump to topic
Re: Picture of the day. (Taken by you)
I would ALWAYS use that for opening boxes, just because I could!
- Mon May 20, 2024 5:37 pm
- Jump to forum
- Jump to topic
Re: Are we ready to add an RC10T ReRe section?
Now that AE is catching on, MIP needs to get with it too and rerelease what everyone wants... not just a new screwdriver
I'm sure they could have a ReRe section too.
I'm sure they could have a ReRe section too.
- Tue May 21, 2024 9:46 am
- Jump to forum
- Jump to topic
Re: Project Hyper Hornet
In addition to having springs that are too soft, the tiny front shocks are horrible leakers. A front shock upgrade is needed. I have a spare set that are the right length and seem like a natural fit. . 1000011051.jpg . However stiffer shocks = more shock tower deflection. The tweaked shock tower I p...
- Tue May 21, 2024 3:45 pm
- Jump to forum
- Jump to topic
Re: My first RC10T. But, what is it?
A few of the versions from T to T4, and GT:
. . . . . .
. . . . . .
- Tue May 21, 2024 10:07 pm
- Jump to forum
- Jump to topic
Re: Looking for a 9601 top shaft
Do you need a brand new top shaft, or just a usable top shaft?